M811 ENERCON | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 7
Technical content
Page 1 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in M811 SERIES DC/DC POWER SUPPLY PRODUCT HIGHLIGHTS
- MINIATURE, HIGH DENSITY
- EIGHT OUTPUTS
- UP TO 145 W
- DC/DC POWER SUPPLY
Page 2 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in
Applications
Military (airborne, mobile, shipboard), Ruggedized, Telecom, Industrial Power Supply Special Features
- Miniature size
- High efficiency
- Wide input range
- Input / Output isolation
- Outputs groups isolation
- Fixed switching frequency (~250 kHz)
- External synchronization capability
- Remote inhibit
- EMI filters included
- Non-latching protections:
- Overload / short-circuit protection
- Input under/over-voltage lockout
- Over temperature shutdown Environmental Conditions Meets or exceeds MIL-STD-810G Temperature: Operating –55 C to +85 C (at baseplate) Storage –55 C to +125 C Reliability 150,000 hours, calculated IAW MIL -HDBK- 217F Notice 2 at +85 C baseplate, Ground Fixed conditions. Electrical Specifications DC INPUT Voltage range: 18 to 70 VDC Transient protection: protected against abnormal surge IAW MIL-STD-1275A (100 V / 50 ms) and MIL-STD-704A (80 V / 0.1 s) Efficiency: Up to 80% EMC: Designed to meet MIL-STD-461F* CE101, CE102, CS101, CS114, CS115, CS116, RE101, RE102, RS101, RS103 Isolation: Input to Output: 200 VDC Input to Case: 200 VDC DC OUTPUTS Voltage regulation: ≤ ±1% (low to high line voltage, no load to full load, –55 C to +85 C) Ripple and Noise: 50 mVp-p, typ. (max. 1%) Overcurrent protection: current limit (CC) beyond threshold. Over voltage protection: Passive protection. Over temperature protection: Shutdown if baseplate temperature exceeds +105 C ± 5 C; Automatic recovery upon baseplate cooldown to below +95 C ± 5 C. Isolation: Output and Case: 100 VDC *EMC compliance achieved when tested with 5 μH LISNs , shielded harness and static resistive load.
Page 3 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Operational Block Diagram
Page 4 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Outputs Configuration Range Output # Voltage Range Current Range Power Range 1 2.5 to 28 VDC 0 to 3 A 0 to 40 W 2 1.5 to 28 VDC 0 to 4 A 0 to 40 W 3 2.5 to 28 VDC 0 to 3 A 0 to 20 W 4 2.5 to 28 VDC 0 to 5 A 0 to 30 W 5 2.5 to 28 VDC 0 to 8 A 0 to 30 W 6 1.25 to 28 VDC 0 to 5 A 0 to 15 W 7 2.5 to 28 VDC 0 to 2.5 A 0 to 15 W 8 -2.5 to -28 VDC 0 to 2.5 A 0 to 15 W Total 0 to 145 W Outputs Isolation (Ground RTN groups)
- All outputs are isolated form the input.
- Outputs are separated into the following four galvanically isolated groups: o Group A: Output #1 o Group B: Output #2, #4, #5 and #6 o Group C: Output #3 o Group D: Outssputs #7 and #8
Page 5 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Pin Assignment Connector type: M55302/61-A36 or eq. Mating connector type: M55302/62-A36M (solder cup termination) or M55302/66- 32M (#22 AWG crimp termination) or eq. Pin # Function P Pin # Function P Pin # Function P
1 INPUT +
13 OUT 1 +
25 OUT 5 +
2 INPUT +
14 OUT 2 +
26 OUT 2,4,5,6
RTN –
3 INPUT RTN –
15 INHIBIT +
27 OUT 2,4,5,6
RTN –
4 INPUT RTN –
16 OUT 8 –
28 OUT 2,4,5,6
RTN –
5 OUT 2,4,5,6
RTN –
17 OUT 7,8 RTN
29 OUT 4 +
6 OUT 6 +
18 OUT 7 +
30 CHASSIS
7 OUT 5 +
19 INPUT +
31 OUT 2 +
8 OUT 5 +
20 INPUT +
32 SIGNAL RTN –
9 OUT 2,4,5,6
RTN –
21 INPUT RTN –
33 SYNC +
10 OUT 2,4,5,6
RTN –
22 INPUT RTN –
34 OUT 7,8 RTN
11 OUT 4 +
23 OUT 2,4,5,6
RTN –
35 OUT 3 +
12 OUT 1 RTN –
24 OUT 6 +
36 OUT 3 RTN –
Page 6 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Signals Description INHIBIT (pin 31) The INHIBIT signal is used to turn the power supply ON and OFF. TTL “1”or OPEN – Power supply active (output turned on). TTL “0” or SHORT to SIGNAL RTN – Power supply inhibited (output turned off). If this function is not required, leave this pin unconnected. This signal is referenced to SIGNAL RTN (pin 32) SYNC (pin 33) The SYNC signal is used to synchronize the power supply's switching frequency to system's clock. If this function is not required, leave this pin unconnected - the power supply will use its internal clock. External clock frequency can be between 240 kHz to 260 kHz, with duty cycle of 40% to 60%. Valid clock voltage level is between 5 to 12 V. This signal is referenced to SIGNAL RTN (pin 32) SIGNAL RTN (pin 32) Both INHIBIT and SYNC signals are referenced to this pin. This pin is referenced to INPUT TN (pins 3, 4, 21 and 22).
Page 7 of 7 Nov 9, 2021 | Rev g | Doc: DS_M811 Series M811 SERIES DC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Outline Drawing Heat Dissipation Surface Area Surface Area 3.947 in² (2,547 mm²) Notes 1. Dimensions are in inches [mm] 2. Tolerance is: .XX .02 in .XXX .01 in 3. Weight: Approx. 14 oz [400 g] Note: Specifications are subject to change without prior notice by the manufacturer