M200

M200 CYPRESS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 17

Technical content

Datasheet sections

• 2 Configurable PLLs

Features

■ Device Operating Voltage Options: ❐ MoBL Clock M200 Family: 1.8 V ❐ MoBL Clock M500 Family: 2.5 V, 3.0 V, or 3.3 V ■ Selectable clock output voltages for both MoBL Clock M200 and M500: ■ Fully integrated ultra low power phase-locked loops (PLLs) ■ Input reference clock frequency range: 1–48 MHz ■ Output clock frequency range: 3–50 MHz ■ Three I2C™ programmable output clocks ■ Programmable output drive strengths ■ 150 ps typical cycle-to-cycle jitter ■ Optional Spread Spectrum for EMI reduction ■ 16-pin (3 × 3 × 0.6 mm) QFN Package ■ Industrial temperature range Benefits ■ Suitable for cell phone, portable, and consumer electronics

applications

■ Multiple high-performance PLLs allow synthesis of unrelated frequencies ■ Application compatibility in multiple output voltage levels ■ Optional Spread Spectrum capable PLLs with Lexmark or Linear profile for maximum EMI reduction ■ PLLs can be programmed for system frequency margin tests ■ Meets critical timing requirements in complex system designs ■ Individually enable or disable each output using I2C ■ Ease of output clock selection using programmable crossbar switches Logic Block Diagram PLL1 PLL2 (SS) Output Dividers and Drive Strength Control Crossbar Switch PD#/OE CLK1 CLK3 CLK2 VDD_CLK1 VDD_CLK3VDD_CLK2 REF SEL MUX and Control Logic I2C EXCLKIN SCL SDA [+] Feedback

Figure 1. Pin Diagram - 16 LD QFN

16 LD QFN

Table 1. Pin Definitions - MoBL Clock M200 Family (VDD = 1.8 V Supply)

1 VSS Power GND

4 PD#/OE Input Multifunction Programmable pin: Output Enable or Power Down

5 VSS Power GND

6 SCL Input I 2C-Bus Clock Line

7 SDA Input/Output I 2C-Bus Data Line

8 VSS Power GND

12 DNU DNU Do Not Use this pin

13 VSS Power GND

Figure 2. Pin Diagram - 16 LD QFN Table 2. Pin Definitions - MoBL Clock M500 Family (VDD = 2.5 V, 3.0 V or 3.3 V Supply)

2 Configurable PLLs

from a single input reference clock. in-system control of these programmable features. the DC and AC specifications. These devices have three clock outputs, CLK1, CLK2 and CLK3. source selection is done using three out of three crossbar switch. Lexmark or Linear modulation profile. PD# turn-on time is limited by the turn-on time of the PLLs. Disabled outputs are first driven to a low state before turning off. clock outputs can be programmed to be sensitive to this OE pin. and outputs, but preserves the contents of the volatile registers. reduced relative to the Keep Alive Mode. and fall times for different drive strength settings. Application Engineer (FAE) or sales representative. Table 3. Output Drive Strength

Figure 3. Data Transfer Sequence on the Serial Bus Figure 4. Data Frame Architecture Figure 5. Data Valid and Data Transition Periods

1 Bit

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 9 of 17 Absolute Maximum Conditions Parameter Description Condition Min Max Unit VDD Supply Voltage for MoBL Clock M5xx –0.5 4.4 V VDD Supply Voltage for MoBL Clock M2xx –0.5 2.8 V VDD_CLKX Supply Voltage for MoBL Clock M2xx/M5xx –0.5 4.4 V VIN Input Voltage for MoBL Clock M5xx Relative to V SS –0.5 V DD + 0.5 V VIN Input Voltage for MoBL Clock M2xx Relative to V SS –0.5 2.2 V TS Temperature, Storage Non Functional –65 +150 °C ESDHBM ESD Protection (Human Body Model) JEDEC EIA/JESD22-A114-E 2000 – V UL-94 Flammability Rating V-0 @1/8 in. – 10 ppm MSL Moisture Sensitivity Level 3 Recommended Operating Conditions The Recommended Operating Conditions table for MoBL Clock M2xx/M5xx family. Parameter Description Min Typ Max Unit VDD VDD Operating voltage for MoBL Clock M5xx 2.25 – 3.60 V VDD VDD Operating voltage for MoBL Clock M2xx 1.65 1.80 1.95 V VDD_CLKX Output Driver Voltage for MoBL Clock M2xx/M5xx 1.43 – 3.60 V TAI Industrial Ambient Temperature –40 – 85 °C CLOAD Maximum Load Capacitance – – 15 pF tPU Power up time for all VDDs to reach minimum specified voltage (power ramps must be monotonic) 0.05 – 500 ms [+] Feedback

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 10 of 17 Parameter Description Conditions Min Typ Max Unit VOL Output Low Voltage I OL = 2 mA, drive strength = [00] – – 0.4 V IOL = 3 mA, drive strength = [01] IOL = 7 mA, drive strength = [10] IOL = 12 mA, drive strength = [11] VOH Output High Voltage I OH = –2 mA, drive strength = [00] V DD_CLKX – 0.4 –– V IOH = –3 mA, drive strength = [01] IOH = –7 mA, drive strength = [10] IOH = –12 mA, drive strength = [11] VOLSD Output Low Voltage, SDA I OL = 4 mA – – 0.4 V VIL1 Input Low Voltage of PD#/OE, SDA and SCL pins – – 0.2 × V DD V VIL2 Input Low Voltage of EXCLKIN pin – – 0.1 × V DD V VIH1 Input High Voltage of PD#/OE, SDA and SCL pins 0.8 × VDD –– V VIH2 Input High Voltage of EXCLKIN for MoBL Clock M5xx 0.9 × VDD –– V VIH3 Input High Voltage of EXCLKIN pin MoBL Clock M2xx 0.9 × VDD –2 . 2 V IIH Input High Current, PD#/OE V IH = VDD – – 10 µA IIL Input Low Current, PD#/OE V IL = 0 V – – 10 µA RDN Pull Down Resistor of clocks (CLK1-CLK3) in off-state Clock outputs in off-state by setting PD# = Low 100 160 250 k  IDD [1, 2] Supply Current All outputs running, C LOAD = 0 – 15 – mA IDDS [1] Standby Current PD# = Low, I2C circuit not in Keep Alive Mode –3 – µ A CIN [2] Input Capacitance SCL, SDA, and PD#/OE inputs – – 7 pF Notes 1. This parameter is configuration dependent. The specif ied value is for the drive level setting of [1,1]. 2. Parameters are guaranteed by design and characterization. Not 100% tested in production. All parameters specified with fully loaded outputs. [+] Feedback

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 11 of 17 Notes 3. This parameter is configuration dependent. The specif ied value is for the drive level setting of [1,1]. 4. Parameters are guaranteed by design and characterization. Not 100% tested in production. All parameters specified with fully loaded outputs. Parameter Description Conditions Min Typ Max Unit FCLK Clock Output Frequency All clock outputs 3 – 50 MHz FREF Driven Reference Frequency EXCLKIN Clock 1 – 48 MHz DC Output Clock Duty Cycle Duty Cycle as defined in Figure 9 on page 12 t1/t2, 50% of VDD_CLKX 45 50 55 % TRF1 [4] Output Clock Rise/Fall Time Measured from 20% to 80% of VDD_CLKX, as shown in Figure 10 on page 12, CLOAD = 15 pF, drive strength [00] – 6.8 10.0 ns TRF2 [4] Output Clock Rise/Fall Time Measured from 20% to 80% of VDD_CLKX, as shown in Figure 10 on page 12, CLOAD = 15 pF, drive strength [01] –3 . 4 5 . 0 n s TRF3 [4] Output Clock Rise/Fall Time Measured from 20% to 80% of VDD_CLKX, as shown in Figure 10 on page 12, CLOAD = 15 pF, drive strength [10] –2 . 0 3 . 0 n s TRF4 [4] Output Clock Rise/Fall Time Measured from 20% to 80% of VDD_CLKX, as shown in Figure 10 on page 12, CLOAD = 15 pF, drive strength [11] –1 . 0 1 . 5 n s TCCJ [3, 4] Cycle-to-cycle Jitter EXCLK IN = CLKx = 48 MHz, CLOAD = 15 pF, 2 PLLs and 1 output for each PLL enabled, drive strength = [11] –1 5 0 – p s TLOCK [4] PLL Lock Time – 1 3 ms [+] Feedback

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 13 of 17 All product offerings are factory programmed customer specific devices with customized part numbers. The Possible Configurations table shows the available device types, but not complete part numbers. Contact your local Cypress FAE of Sales Representative for more information. Possible Configurations Note 5. xx indicates factory programmed parts based on customer specific configuration. For more details, contact your local Cypress FAE or Sales Representative

Ordering Information

Part Number [5] Frequency Configuration Other Programmable Features Package Production Flow Pb-Free M200LFXI Factory Generic Configuration With EXCLKIN = 19.2 MHz CLK1 = 48.0 MHz CLK2 = 27.0 MHz VDD = 1.8 V Power Down = Enabled Keep Alive = Disabled Spread Spectrum = Disabled Output Drive Strength = [11] 16-pin QFN Industrial, –40 °C to 85 °C M200LFXIT Factory Generic Configuration With EXCLKIN = 19.2 MHz CLK1 = 48.0 MHz CLK2 = 27.0 MHz VDD = 1.8 V Power Down = Enabled Keep Alive = Disabled Spread Spectrum = Disabled Output Drive Strength = [11] 16-pin QFN- Tape & Reel Industrial, –40 °C to 85 °C M500LFXI Factory Generic Configuration With EXCLKIN = 19.2 MHz CLK1 = 48.0 MHz CLK2 = 27.0 MHz VDD = 2.5 V/3.0 V/3.3 V Power Down = Enabled Keep Alive = Disabled Spread Spectrum = Disabled Output Drive Strength = [11] 16-pin QFN Industrial, –40 °C to 85 °C M500LFXIT Factory Generic Configuration With EXCLKIN = 19.2 MHz CLK1 = 48.0 MHz CLK2 = 27.0 MHz VDD = 2.5 V/3.0 V/3.3 V Power Down = Enabled Keep Alive = Disabled Spread Spectrum = Disabled Output Drive Strength = [11] 16-pin QFN- Tape & Reel Industrial, –40 °C to 85 °C Part Number [5] Frequency Configuration Other Programmable Features Package Production Flow M2xxLFXI Customer Specific Configuration VDD = 1.8 V 16-pin QFN Industrial, –40°C to 85°C M2xxLFXIT Customer Specific Configuration VDD = 1.8 V 16-pin QFN- Tape & Reel Industrial, –40°C to 85°C M5xxLFXI Customer Specific Confi guration VDD = 2.5 V/3.0 V/3.3 V 16-pin QFN Industrial, –40°C to 85°C M5xxLFXIT Customer Specific Configuration VDD = 2.5 V/3.0 V/3.3 V 16-pin QFN- Tape & Reel Industrial, –40°C to 85°C [+] Feedback

Figure 11. 16-Lead Chip On Lead 3 × 3 mm QFN Package

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 15 of 17 Acronyms Document Conventions Units of Measure Acronym Description EMI electromagnetic interference FAE field application engineer OE output enable PLL phase locked loop QFN quad flat no leads Symbol Unit of Measure °C degree Celsius k kilo ohms kHz kilo Hertz MHz Mega Hertz µA micro Amperes mA milli Amperes ms milli seconds mm milli meter ns nano seconds  ohms % percent pF pico Farads ppm parts per million ps pico seconds Vv o l t s [+] Feedback

MoBL® Clock M200/M500 Document Number: 001-29139 Rev. *C Page 16 of 17 Document History Page Document Title: MoBL® Clock M200/M500 Two-PLL Programmable Clock Generator for Portable Applications Document Number: 001-29139 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 1535744 See ECN RGL/AESA New Data Sheet *A 2748211 08/10/09 TSAI Posting to external web. *B 2899297 03/25/10 CXQ Moved ‘xx’ parts to Possible Configurations table. Updated Package Diagram *C 3095377 11/25/ 2010 BASH Added Ordering Code Definitions. Added Acronyms and Units of Measure. Minor edits and updated in new template. [+] Feedback

Document Number: 001-29139 Rev. *C Revised November 25, 2010 Page 17 of 17 Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. MoBL is a registered trademark of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders. MoBL® Clock M200/M500 © Cypress Semiconductor Corporation, 2007-2010. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subj ect to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to t he materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ prod uct in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive cypress.co m/go/automotive Clocks & Buffers cypress.com/go/clocks Interface cypress. com/go/interface Lighting & Power Control cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory Optical & Image Sensing cypress.com/go/image PSoC cypress.com/go/psoc Touch Sensing cyp ress.com/go/touch USB Controllers cypress.com/go/USB Wireless/RF cypress.com/go/wireless PSoC Solutions psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 5 [+] Feedback