M1B-0618 MARKIMICROWAVE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
LO/RF 6.0 to 18.0 GHz IF DC to 4.0 GHz 5.5 dB Typical Conversion Loss 33 dB Typical LO to RF Isolation Recommended for Bi-Phase Applications Broadband RF and LO For a list of recommended LO driver amps for all mixers and IQ mixers, see here. Electrical Specifications - Specifications guaranteed from -55 to +100C, measured in a 50-Ohm system. Parameter LO RF IF Min Typ Max Diode Option (GHz) (GHz) (GHz) LO drive level (dBm) 14-18 14-18 DC-2.0 6.5 9 14-18 14-18 2.0-4.0 7.5 10 Isolation (dB) LO-RF 6.0-18.0 6.0-18.0 25 33 Input 1 dB Compression (dBm) 6.0-18.0 6.0-18.0 +2 L (+7 to +10) +5 M (+10 to +13) +8 N (+13 to +16) +11 H (+16 to +19) +14 S (+19 to +22) Input Two-Tone Third Order Intercept Point (dBm) +15 M (+10 to +13) +18 N (+13 to +16) +21 H (+16 to +19) +24 S (+19 to +22) Part Number Options Please specify diode level and package style by adding to model number. Package Options Examples Microstrip 1,2 E M1B-0618 L E -2 Connectorized P (Model) (Diode Option) (Package) (I-Port Configuration) 1Connectorized test fixtures available for most microstrip packages. Consult factory. 2For non-connectorized packages, specify I-port configuration by adding –1 or –2 suffix to model number. Default is –2 configuration when not specified.
Copyright © [2019, 2020] Marki Microwave, Inc. All Rights Reserved. DOUBLE-BALANCED MIXERS BI-PHASE MODULATORS M1B-0618 Page 2 LO/RF 6.0 to 18.0 GHz IF DC to 4.0 GHz Typical Performance Ref Conversion Loss - dB4.0 5.0 6.0 7.0 Relative IF Response - dB 1.0 3.0 2.0 LO to RF/IF Isolation - dB LO/RF Port VSWR1:1 3:1 2:1
20 L-I
6.0 GHz 18.06.0 GHz 18.0 DC GHz 4.0 LO RF 6.0 GHz 18.0 Bi-Phase Insertion Loss - dB 4.0 3.0 2.0 1.0 6.0 GHz 18.0 Bi-Phase Amplitude Match - dB1.0 -1.0 Ref 6.0 GHz 18.0 Bi-Phase Deviation - Degrees -5.0 Ref 5.0 6.0 GHz 18.0 DATA SHEET NOTES: 1. Mixer Conversion Loss Plot IF frequency is 100 MHz. 2. Mixer Noise Figure typically measures within +0.5 dB of conversion loss for IF frequencies greater than 5 MHz. 3. Conversion Loss typically degrades less than 0.5 dB for LO drives 2 dB below the lowest and 3 dB above highest nominal LO drive levels. 4. Conversion Loss typically degrades less than 0.5 dB at +100°C and improves less than 0.5 dB at -55°C. 5. Maximum input power is +23 dBm at +25°C, derated linearly to +20 dBm at +100°C. 6. Specifications are subject to change without notice. Contact Marki Microwave for the most recent specifications and data sheets. 7. Standard configuration for A, B, and C outlines are with connectors and bottom spacer. 8. Catalog mixer circuits are continually improved. Configuration control requires custom mixer model numbers and specifications. Marki Microwave reserves the right to make changes to the product(s) or information contained herein without notice . Marki Microwave makes no warranty, representation, or guarantee regarding the suitability of its products for any particular p urpose, nor does Marki Microwave assume any liability whatsoever arising out of the use or application of any product. www.markimicrowave.com