M1963 ENERCON | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 9
Technical content
Page 1 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in
Applications
1-PHASE AC/DC POWER SUPPLY PRODUCT HIGHLIGHTS
- HIGH POWER FACTOR
- TRIPLE OUTPUT
- 1-PHASE AC/DC POWER SUPPLY
- UP TO 130 W
Page 2 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Military (Airborne, ground-fix, shipboard), Ruggedized, Telecom, Industrial Power Supply Special Features
- Miniature size
- High efficiency
- High power factor (up to 96%)
- Input / Output isolation
- Fixed switching freq. (450 kHz for output converters)
- EMI filters included
- Remote inhibit (On/Off)
- Limited inrush current
- Non-latching protections: o Overload/short-circuit o Over temperature Out Option Voltage Range Max Current Max Power 1 A 0.8-12 V 5 A 60 W B 0.8-40 V 3.5 A 2 A 0.8-12 V 5A 60 W B 0.8-40 V 3.5 A 3 A 0.6-5 V 8 A 40 W * Compliance dependent on specific configuration, and is achieved when using shielded interconnection cable. Electrical Specifications AC Input Single-phase 85 to
265 VAC
Less than ±1% (no load to full load, –40 C to +85 C at baseplate). Ripple and Noise 100150 mVp-p, typical (max. 1%) without external capacitance. DC Output Total output power: up to 130 W Efficiency 83% Typical (at nominal input voltage, full load, room temperature) Turn on Transient Voltage overshoot at during power on is less than 3% nominal voltage. Isolation Input to Output: 500 VDC Input to Case: 500 VDC Output to Case:
100 VDC Output to Output:
100 VDC
Designed to meet* MIL-STD-461F CE102, CS101, CS114, CS115, CS116 RE102, RS103. CE101, RE101 and RS101 optional. Input Current Harmonics Meets current harmonics requirements of MIL-STD- 1399:300B and EN 61000-3-2 Classes A, B and D.
Page 3 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Protections * Input
- Inrush Current Limiter Peak value of up to 5 times of maximum steady-state input current for inrush currents lasting longer than 50 µs. Output
- Overvoltage protection Passive transorbs selected at 120% ± 10% of nominal voltage.
- Overload / short- circuit protection Continuous protection (constant current) for unlimited time. General
- Over temperature protection: Shutdown at baseplate temperature of +105 C ± 5 C. Automatic recovery when baseplate temperature returns to +95 C ± 5 C. Reliability 100,000 hours, calculated per MIL-STD-217F Notice 2 at +85C baseplate, Ground Fix conditions. Environmental Stress Screening (ESS) 100% of delivered units undergo testing in minimum ambient temperature and maximum baseplate temperature, in addition to testing at room temperature. Additional testing such as random vibration and thermal cycling can be added upon request - consult factory for details and quote if required. * Thresholds and protections can be modified / removed – please consult factory. Vibration Method 514.5 General minimum integrity exposure IAW Figure 514.5C-17 1 hour per axis. Shock Method 516.5 20 g, 11 ms terminal peak saw-tooth Salt Fog Method 509.4 Environmental Conditions Designed to Meet MIL-STD-810F Temperature Methods 501.4 & 502.4 Operating: –40 C to +85 C (at baseplate) Storage: – 55 C to +125 C (ambient) Altitude Method 500.4 Procedures I – up to 70,000 ft. (non-operational) Procedure II – up to 40,000 ft. (operational) Humidity Method 507.4 Up to 95% RH
Page 4 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Typical Efficiency Typical Power Factor Test Conditions: Input: 115 Vrms Outputs: 5 VDC / 8 A, +12 VDC / 3.5 A, -12 VDC / 3.5 A Loss @ 230V/50Hz Loss @ 115V/60Hz Efficiency @ 230V/50Hz Efficiency @ 115V/60Hz 0 10 20 30 40 50 60 70 80 90 100 110 120 Output Power [W] 85% 80% 75% 70% 65% 60% 55% 50% 45% 40% 35% 30% 25% 20% 230V/50H z 115V/60H z Output Power [W] 90 100 110 120 0.9 0.8 0.7 0.6 0.5 0.4 Efficienc y Power Factor Loss [W]
Page 5 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Typical test results PWRGOOD Signal Resist after 5V source PWRGOOD Voltage
1 MΩ 31mV
100 KΩ 0.14V 10KΩ 0.36V 1KΩ 1V Pin Assignment Connector type: M24308/24-39F or eq. Mating connector type: M24308/2-3F or eq. Pin No. Function P Pin No. Function P
1 LINE (IN) ~
2 N/C 14 N/C
3 N/C 15 NEUTRAL (IN) 0
4 INHIBIT + 16 N/C
5 SIGNAL RTN – 17 SYNC +
6 PWR GOOD RTN – 18 PWR GOOD +
7 OUT 3 + 19 OUT 3 +
8 OUT 3 RTN – 20 OUT 3 +
9 OUT 3 RTN – 21 OUT 3 RTN –
10 OUT 2 + 22 OUT 2 +
11 OUT 2 RTN – 23 OUT 2 RTN –
12 OUT 1 + 24 OUT 1 +
13 OUT 1 RTN – 25 OUT 1 RTN –
Page 6 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Functions and Signals INHIBIT (pin 4) Description: The INHIBIT signal is used to turn the power supply ON and OFF. Operation: Applying “1” or leaving open will turn the power supply ON. Applying “0” or shorting this pin to its return line will turn the power supply OFF. For constant operation, leave this pin unconnected. Signal Type: 5V TTL or dry contact (open/short). Return line: This signal is referenced to SIGNAL RTN (pin 5). SYNC (pin 17) Description: The SYNC signal can be used to allow the power supply switching frequency to synchronize with a system clock. Operation: Apply a square wave clock with frequency in the range of 450 kHz ± 10 kHz and duty-cycle of 50% ± 10%., TTL level. If not required, leave open. The power supply will work at 450 kHz ± 10 kHz (internal clock). Signal Type: 5V TTL Return line: This signal is referenced to SIGNAL RTN (pin 5). PWR GOOD (pin 18) Description: The PWR GOOD signal indicates the status of the output voltage. Operation: When the output voltages rise above 90% ± 5% of its nominal value, pin 18 will be pulled down to pin 6 through a 100 Ω ± 1% resistor and three phototransistors. When one of the output voltages falls below 90% ± 5% of its nominal value, pin 18 will be in high impedance mode. If not used, leave the signal unconnected. This signal is the series connection of three opto-couplers and a 100 Ω resistor to limit the current. Signal Type: Isolated open collector. Return line: This signal is referenced to PWR GOOD RTN (pin 6) and is floating from all other pins. WARNING: Mind the polarity! Connecting a reverse polarity voltage source with current limit higher than 30mA to this signal will result in permanent damage to the converter. SIGNAL RTN (pin 5) Description: Both INHIBIT and SYNC signals are referenced to this pin.
Page 7 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Typical Connection Diagram Note: PWR GOOD- the load for the pull-up resistor and the auxiliary voltage shown in this diagram should be less than 1mA. The system designer must select the actual values such that no damage can occur to the internal components of the power supply – consult factory for more information
Page 8 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Outline Drawing Notes 1. Dimensions are in inches [mm] 2. Tolerance is: .XX .02 in .XXX .010 in 3. Weight: approx. 14.46 oz [410 g] Note: Specifications are subject to change without prior notice by the manufacturer. Heat Dissipation Area 18.7 in2 [120.64 cm²]
Page 9 of 9 Aug 10, 2021 | Rev (g) | Doc: DS_M1963 Series M1963 Series– AC/DC Power Supply Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Label position