M185 ENERCON | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
Page 1 of 5 Feb 15, 2023 | Rev f | Doc: DS_M185 Series M185 SERIES AC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in M185 SERIES AC/DC POWER SUPPLY PRODUCT HIGHLIGHTS
- MINIATURE
- HIGH DENSITY
- AC/DC CONVERTER
- QUAD OUTPUT
- UP TO 150W
Page 2 of 5 Feb 15, 2023 | Rev f | Doc: DS_M185 Series M185 SERIES AC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in
Applications
Military, Ruggedized, Telecom, Industrial Special Features
- Four (4) DC outputs
- High efficiency
- Wide input range
- Input / Output isolation
- Fixed internal switching frequency (250 kHz)
- External synchronization ability
- EMI filters included
- Input undervoltage lockout (< 75 VAC) Environmental Conditions Meets or exceeds MIL- STD-810D Temperature: Operating -40°C to +90°C (baseplate) Storage -55°C to +125°C Reliability 150,000 hours, calculated per MIL-STD-217F Notice 2 at +85°C baseplate, ground fixed. Protections Current limiting (indefinite): Outputs 1 through 3: Foldback Output 4: Hiccup Over Voltage Protection: Outputs 1 through 3: Passive transorb. Output 4: Crowbar. Over Temperature Protection: Shutdown at baseplate temperature above +105C 5C. Automatic recovery at baseplate temperature below +95C 5C Electrical Specifications AC INPUT Input range: 90-265VAC, 400Hz, Single-Phase (85- 265VAC, 50/60/400Hz Single-Phase option available) Power Factor: 0.98 Efficiency: up to 75% EMC: Meet MIL-STD-461F*: CE101, CE102, CS101, CS114, CS115, CS116, RE101, RE102, RS101, RS103 Isolation: Input to Outputs: 500 VDC Input to Case: 500 VDC DC OUTPUT (floating from each other) Outputs range: Output Voltage Current Power 1 3.3 to 24VDC 0 to 5A 0 to 30W 2 3.3 to 24VDC 0 to 5A 0 to 30W 3 3.3 to 24VDC 0 to 10A 0 to 60W 4 1.8 to 15VDC 0 to 30A 0 to 100W Line/Load regulation: Up to ±1% (no load to full load, –40C to +85C) Ripple and Noise: 50mVp-p, typical (max. 1%) Isolation: Outputs to Case: 100VDC
- Compliance achieved with shielded harness and static resistive load.
Page 3 of 5 Feb 15, 2023 | Rev f | Doc: DS_M185 Series M185 SERIES AC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Pin Assignment Input Connector (P1): Connector type: M24308/24-37F or eq. Mates with: M24308/4-1F or M24308/23-7 or eq. Pin No. Function Pin No. Function 1 CHASSIS 6 N.C. 2 N.C. 7 NEUTRAL 3 NEUTRAL 8 N.C. 4 N.C. 9 PHASE
5 PHASE
Output Connector (J2): Connector type: M24308/23-46F or eq. Mates with: M24308/2-4F or eq. Pin No. Function Pin No. Function Pin No. Function
1 INHIBIT 14 OUT #4 (+) 27 SENSE RTN OUT #4
2 SYNC 15 OUT #4 (+) 28 OUT #4 RTN (–)
3 OUT #3 RTN (–) 16 OUT #4 (+) 29 OUT #4 RTN (–)
4 OUT #3 (+) 17 OUT #4 (+) 30 OUT #4 RTN (–)
5 OUT #3 (+) 18 OUT #4 (+) 31 OUT #4 RTN (–)
6 OUT #2 (+) 19 SENSE OUT #4 32 OUT #4 RTN (–)
7 N.C. 20 INHIBIT RTN 33 OUT #4 (+)
8 OUT #1 (+) 21 SYNC RTN 34 OUT #4 (+)
9 OUT #4 RTN (–) 22 OUT #3 RTN (–) 35 OUT #4 (+)
10 OUT #4 RTN (–) 23 OUT #3 RTN (–) 36 OUT #4 (+)
11 OUT #4 RTN (–) 24 OUT #3 (+) 37 OUT #4 (+)
12 OUT #4 RTN (–) 25 OUT #2 RTN (–)
13 OUT #4 RTN (–) 26 OUT #1 RTN (–)
Note: All pins with identical function/designation should be connected together for best performance.
Page 4 of 5 Feb 15, 2023 | Rev f | Doc: DS_M185 Series M185 SERIES AC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Functions and Signals INHIBIT signal The INHIBIT signal is used to turn the power supply ON and OFF. TTL “1” or OPEN will turn on the power supply (For normal operation leave the signal not connected). TTL “0” or SHORT will turn off the power supply. This signal is referenced to INHIBIT RTN pin and is isolated from all other pins. SYNC signal The SYNC signal is used to allow the power supply frequency to sync with the system frequency. The system frequency should be 250 kHz ± 10 kHz. When not connected the power supply will work at 250 kHz ± 10 kHz. This signal is referenced to SYNC RTN pin and is isolated from all other pins. SENSE The SENSE is used to achieve accurate load regulation at load terminals of output #4. This is done by connecting the pins directly to the load terminals. The remote sense correction function is limited to voltage drop between converter’s output and load terminals of 2% to 5%, or up to 0.5V, the least of the two. When not used, connect SENSE to OUT #4 and SENSE RTN to OUT #4 RTN. Do not leave SENSE and SENSE RTN pins unconnected. These pins can be tied internally to avoid external connection, if function is not required – consult factory.
Page 5 of 5 Feb 15, 2023 | Rev f | Doc: DS_M185 Series M185 SERIES AC/DC POWER SUPPLY Switzerland sales@enercon-europe.com Israel sales@enercon.co.il India sales@mpsindia.in Outline Drawing Note: Specifications are subject to change without prior notice by the manufacturer. Notes 1. Dimensions are in inches [mm] 2. Tolerance is: .XX .02 in .XXX .01 in 3. Weight: 40 oz (1 150 g)