LSTD205-6DBK-XX

LSTD205-6DBK-XX LIGITEK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only TRIPLE DIGIT SMD DISPLAY (0.20") LSTD205/6DBK-XX DATA SHEET DOC.NO : QW0905- LSTD205/6DBK-XX R E V . : A DATE : 17 – May. – 2013 發行 DCC 立碁電子

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 1 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Package Dimensions PART NO. NOTE: Dimension in millimeters (inches), And tolerance are 0.25mm (.01") specified. DATE CODE Recommended Soldering Pad Dimensions 6.80 13.00 2.54X5=12.70 3.102.54X4=10.16 2.00 0.54

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 2 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Internal Circuit Diagram 11 7 LSTD205DBK-XX (Common Cathode) A B C D E F G DP DIG1 DIG2 DIG1-DIG3 DIG3 LSTD206DBK-XX (Common Anode) 611 97413 1 0 82 DIG.1 DIG.3 DIG.1 DIG.3 ABCDEF G D P ABCDEF G D P ABCDEF G D P ABCDEF G D P DIG.2 ABCDEF G D P 611 97413 1 0 82 DIG.2 ABCDEF G D P

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 3 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Electrical Connection PIN NO. LSTD205DBK-XX PIN NO. LSTD206DBK-XX

1 Anode D 1 Cathode D

2 Anode DP 2 Cathode DP

3 Anode E 3 Cathode E

4 Anode C 4 Cathode C

5 Common Cathode DIG2 5 Common Cathode DIG2

6 Common Cathode DIG3 6 Common Cathode DIG3

7 Anode B 7 Cathode B

8 Anode G 8 Cathode G

9 Anode A 9 Cathode A

10 Anode F 10 Cathode F

11 Common Cathode DIG1 11 Common Cathode DIG1

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 4 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25°C Parameter Symbol Ratings UNIT Power Dissipation PD 120 mW Peak pulse current Duty 1/10@10KHz I FP 100 mA Forward Current Per Chip I F 30 mA Debating liner from 25°C per segment --- 0.3 mA / °C Storage Temperature T stg -40 ~ +105 °C Operating Temperature T opr -40 ~ +105 °C Typical Electrical & Optical Characteristics (Ta=25°C) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Intensity IV ---- 20 mcd IF=20mA Spectral Line Half-Width ΔΡ ---- 30 ---- nm IF=20mA Forward Voltage VF ---- 3.2 4.0 V IF=20mA Reverse Current Ir ---- ---- 10 μA VR=5V Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2.The luminous intensity data did not including ±15% testing tolerance.

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 5 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Electro-Optical Characteristics Curve (25 ℃ Free Air Temperature Unless Otherwise Specified) DBK: SUPER BRIGHT BLUE (InGaN) CURVE

TEL:02-7703-6000 FAX ：02-7703-6286 No. 238, Bo-ai St., Shulin District, New Taipei City 238, Taiwan R.O.C www.ligitek.com © 2011 LIGITEK All Rights Reserved Page 6 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SMT REFLOW SOLDERING INSTRUCTIONS ≦5 SEC. 100SEC.MAX. 255-260 °C 217 °C 200 °C 150 °C 60-120SEC. TEMPERATURE TIME SMT Soldering Profile Pb free reflow soldering Profile 3 °C/SEC.MAX. 3 °C/SEC.MAX. 6 °C/SEC.MAX. SOLDERING IRON Basic spec is ≦4 sec when 260°C. If temperature is higher, time should be shorter (+10°C→1 sec). Power dissipation of Iron should be smaller than 15W, and temperature should be controllable. Surface temperature of the device should be under 230°C. REWORK Customer must finish rework within 3 sec. under 350 . ℃ The head of soldering iron cannot touch copper foil.