LPQ201-M ARTESYN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
200 Watts
Total Power: 100 - 200 Watts Input Voltage: 90 - 264 Vac # of Outputs: Quad SPECIAL FEATURES Medical and ITE safeties Active power factor correction 3” x 5” footprint Less than 1U high EN61000-3-2 compliant Remote sense Power fail Adjustable outputs Built-in Class B EMI filter Overvoltage protection Overload protection Thermal overload protection LPX200 enclosure kit available RoHS compliant SAFETY TUV 60950, 60601-1 UL 60950, 60601-1 CSA 60950, 60601-1 CB Certificate & report CE Mark (LVD) Electrical Specifications Input Input ra nge 90 - 264 Vac; 120 - 300 Vdc Frequency 47 - 63 Hz Inrush current 50 A max., cold start @ 25 °C, 230 Vac input Efficiency 84% typical at full load EMI/RFI FCC Class B conducted; CISPR22 Class B conducted; EN55022 Class B conducted; VDE0878PT3 Class B conducted Safety ground leakage current 275 μA @ 50/60 Hz, 264 Vac input Output Maximum power 100 W for convection; 200 W with 30CFM forced air Adjustment range All outputs -20%, +10%, except for the 3.3 V output which will be Hold-up time 16 ms @ 200 W load, 120 Vac input Overload protection Short circuit protection on all outputs. V1, V2 & V3 overload protected @ 110 - 160%. V4 is 150 - 250% above rating Overvoltage protection 30 - 50% above nominal output on V1 (and V2 on LPQ201-M) Logical Control Power failure Active low logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense Compensates for 0.4 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Data Sheet
LPQ200-M Series Data Sheet Environmental Specifications Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50 °C to 70 °C. -20 °C start up Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10 - 95% Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated 516,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore
Ordering Information
Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30CFM Forced Air Peak Load Regulation2 Ripple P/P (PARD)3 LPQ201-M +3.3 V 0 A 13 A 18 A 20 A ± 2% 50 mV +5 V 0 A 13 A 18 A 20 A ± 2% 50 mV +12 V 0 A 5 A 9 A 10 A ± 5% 120 mV -12 V 0 A 1 A 2 A 2.5 A ± 5% 120 mV LPQ202-M +5 V 0 A 13 A 18 A 20 A ± 2% 50 mV +12 V 0 A 5 A 9 A 10 A ± 5% 120 mV +24 V 0 A 1.5 A 3 A 3.5 A ± 5% 240 mV -12 V 0 A 1 A 2 A 2.3 A ± 5% 120 mV Pin Assignments Connector LPQ200-M SK1 PIN 1 Neutral PIN 3 Line SK2 PIN 1 V1 OUT PIN 2 V2 OUT PIN 3 GND OUT PIN 4 GND OUT PIN 5 GND OUT PIN 6 GND OUT PIN 7 V3 OUT PIN 8 V4 OUT SK3 PIN 1 +V1 Remote sense PIN 2 -V1 Remote sense PIN 3 N/C PIN 4 N/C PIN 5 +Power fail PIN 6 Common PIN 7 N/C PIN 8 Common PIN 9 +V2 Remote Sense (LPQ201-M only) PIN 10 -V2 Remote Sense (LPQ201-M only) Mating Connectors AC Input (SK1) Molex 09-50-3031 (connector) PINS: 08-52-0072 AC Ground Molex 01-90020001 DC Output (SK2) Terminal block Wire size based on Cable Ampacity/AWG Control Signals (SK3) Molex 90142-0010 (USA) PINS: 90119-2110 or AMP: 87977-3 PINS: 87309-8 Artesyn Embedded Technologies Connector Kit #70-841-027, includes all of the above. 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. 4. Mounting hole MH1 is safety ground connection. 5. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C unless otherwise stated. 6. This power supply requires mounting on metal standoffs 0.20” (5 m) in height. 7. Warranty: 2 years 8. Weight: 1.5 lbs/0.68 kg 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users.
LPQ200-M Series Data Sheet WORLDWIDE OFFICES Americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 Asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com LPQ200-M DS 17Mar2016 Mechanical Drawing 100W Output Voltage Adjust POTs 2.55 (64.8) 3.00 (76.2) 0.224 (5.7) (4X) 0.224 (5.7) (4X) 5.00 (127) 4.55 (115.6) PIN - 5 PIN - 10 PIN - 1 PIN -8 SK3 SK2 Ø4 (4X) Mounting Hole V4 Adjust POT PIN - 1 Ground Tab PIN - 3 SK 1 0.06 (1.5) (2X) 0.098 (2.5) MH1 Saety Gnd V1 Pot Adj V2 Pot Adj. V3 Pot Adj