LDGM9033-TR2 LIGITEK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
LDGM9033/TR2DOC. NO : QW0905- REV : DATE : A LDGM9033/TR2 DATA SHEET LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT TAPE AND REEL Lead-Free Parts Pb 12 - Jul - 2010 發行 DCC 立碁電子
2.5 3.05±0.5 5.8±0.5 2.0 4.3±0.5 1.4 Note : The tolerances unless mentioned is ±0.2mm,Angle ± 0.5. Unit=mm. Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. 12±0.3 9.3 Polarity Carrier Type Dimensions 0.7 0.4±0.1 LDGM9033/TR2 Package Dimensions PART NO. 2.8 6.43 5.5 3.05ψ1.554.0 1.75 0.34.0 0.5±0.1 2.0 ψ1.9 Cathode Page1/7 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO.LDGM9033/TR2 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 2/7Page Reel Dimensions 16.0±1.0 74.0±1.514.2±1.0 1500 devices Quantity/Reel 12.0mm tape,7"reel
Description
Part No. ψ178±2.0
V150ESD Electrostatic Discharge Luminous intensity @20mA(mcd) 1100 Min. Forward voltage @20 mA(V) Dominant wave length λDnm Spectral halfwidth △λnm Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. LDGM9033/TR2 PART NO GreenInGaN/GaN MATERIAL Emitted 525Water Clear Lens COLOR 4.0363.5 Typ. Max. Typical Electrical & Optical Characteristics (Ta=25 ℃) Operating Temperature Storage Temperature Tstg Topr -20 ~ +80 -30 ~ +100 Viewing angle 2θ 1/2 (deg) 180020 Typ. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25 ℃ Forward Current Peak Forward Current Duty 1/10@10KHz Power Dissipation Reverse Current @5V LDGM9033/TR2 Parameter PART NO. PD Ir IFP IF 120 100 Symbol DGM Ratings mW μA mA mA UNIT Page 3/7 Peak wave length λPnm 518 Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded.
Fig.3 Forward Voltage vs. Temperature Fig.5 Relative Intensity vs. Wavelength Ambient Temperature(℃) Relative Intensity@20mA Wavelength (nm) Forward Voltage@20mA Normalize @25℃ Fig.4 Relative Intensity vs. Temperature Ambient Temperature(℃) Relative Intensity@20mA Normalize @25℃ Typical Electro-Optical Characteristics Curve Forward Voltage(V) Fig.1 Forward current vs. Forward Voltage Forward Current(mA) Forward Current(mA) Fig.2 Relative Intensity vs. Forward Current Relative Intensity Normalize @20mA LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 1.0 0.1 1.0 100 1000 1.0101001000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40-200204060 1.0 1.1 1.2 450550600 0.0 0.5 1.0 2.03.04.05.0 80100 0.8 0.9 -20-40 4020080100 60 2.0 0.0 0.5 1.0 1.5 2.5 3.0 500 DGM CHIP PART NO. 4/7 PageLDGM9033/TR2
Note: 1.Wave solder and reflow soldering can be only made one time for each other. PART NO. LDGM9033/TR2 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/7 1. Hand Solder Basic spec is ≦ 280℃ 3 sec one time only. Recommended Soldering Conditions 2. Wave Solder Preheat 180~200°C 120 sec.Max. 1~5°C/sec Above 220 °C 60 sec.Max. 120 ~ 180 sec 120 3-2 PB-Free Reflow Solder 60 ~ 120 sec Temp. (℃) 240 3-1. LEAD Reflow Solder 150 Preheat Rising +5℃/sec Time5sec 1~5°C/sec 260°C MaX. 10sec.Max Cooling -5℃/sec 120 ~ 150℃ Preheat 245±5℃ within 5 sec Soldering heat Max. 260℃
(A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5℃ ~ 35℃,RH60%, they should be treated at 60℃±5 ℃fo r 15hrs. LDGM9033/TR2 PART NO. Circuit model B LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 6/7Page
PART NO. Page LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only LDGM9033/TR2 7/7 Reliability Test: Classification Endurance Test Environmental Test Low Temperature Storage Test 1.Ta=-40℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) (10min) (10min) 2.total 10 cycles 30mins 5mins 30mins 5mins
2.10 Cyeles
1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Coverage ≧95% of the dipped surface 1.T=260¢XC Max. 10sec.Max. 2. 6 Min Temperature Cycling IR Reflow Thermal Shock Test High Temperature High Humidity Storage Test Solderability Test 1.Ta=65℃±5℃ 2.RH=90%~95% 3.t=1000hrs ±2hrs MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-750D:2031.2 J-STD-020 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 JIS C 7021: B-12 MIL-STD-202F:103B JIS C 7021: B-11 Test Condition 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) Test Item Operating Life Test High Temperature Storage Test MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 MIL-STD-883D:1008 JIS C 7021: B-10 Reference Standard