FM24C16B_13 CYPRESS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 13
Technical content
Features
16K bit Ferroelectric Nonvolatile RAM Organized as 2,048 x 8 bits High Endurance (1012) Read/Write Cycles 38 year Data Retention NoDelay™ Writes Advanced High-Reliability Ferroelectric Process Fast Two-wire Serial Interface Up to 1MHz maximum bus frequency Direct hardware replacement for EEPROM Supports legacy timing for 100 kHz & 400 kHz Low Power Operation 5V operation 100 A Active Current (100 kHz) 4 A (typ.) Standby Current Industry Standard Configuration Industrial Temperature -40 C to +85 C 8-pin “Green”/RoHS SOIC (-G)
Description
The FM 24C16B is a 16 -kilobit nonvolatile memory employing an advanced ferroelectric process. A ferroelectric random access memory or FRAM is nonvolatile and performs reads and writes like a RAM. It provides reliable data retention for 38 years while eliminating the co mplexities, overhead, and system level reliability problems caused by EEPROM and other nonvolatile memories. The FM 24C16B performs write operations at bus speed. No write delays are incurred. Data is written to the memory array in the cycle after it has been successfully transferred to the device. The next bus cycle may commence immediately without the need for data polling. The FM 24C16B is capable of supporting 10 12 read/write cycles, or a million times more write cycles than EEPROM. These capabilities make the FM 24C16B ideal for nonvolatile memory applications requiring frequent or rapid writes. Examples range from data collection where the number of write cycles may be critical, to demanding industrial controls where the long write time of EEPROM can c ause data loss. The combination of features allows the system to write data more frequently, with less system overhead. The FM24C16B provides substantial benefits to users of serial EEPROM, and these benefits are available as a hardware drop -in replaceme nt. The FM 24C16B is available in an industry standard 8 -pin SOIC package and uses a familiar two-wire protocol. The specifications are guaranteed over the ind ustrial temperature range from -40°C to +85°C. Pin Configuration Pin Names Function SDA Serial Data/Address SCL Serial Clock WP Write Protect VSS Ground VDD Supply Voltage
Ordering Information
FM24C16B-G “Green”/RoHS 8-pin SOIC FM24C16B-GTR “Green”/RoHS 8-pin SOIC, Tape & Reel NC NC NC VSS VDD WP SCL SDA
Figure 1. Block Diagram output driver includes slope control for falling edges. A pull-up resistor is required. the falling edge and clocked-in on the rising edge. all addresses may be written. This pin is internally pulled down.
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 8 of 13 Electrical Specifications Absolute Maximum Ratings Symbol Description Ratings VDD Power Supply Voltage with respect to VSS -1.0V to +7.0V VIN Voltage on any signal pin with respect to VSS -1.0V to +7.0V and VIN < VDD+1.0V * TSTG Storage Temperature -55C to +125C TLEAD Lead Temperature (Soldering, 10 seconds) 260 C VESD Electrostatic Discharge Voltage - Human Body Model (AEC-Q100-002 Rev. E) - Charged Device Model (AEC-Q100-011 Rev. B) - Machine Model (AEC-Q100-003 Rev. E) 4kV 1.25kV 100V Package Moisture Sensitivity Level MSL-1 * Exception: The “VIN < VDD+1.0V” restriction does not apply to the SCL and SDA inputs. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, and the functional operation of the device at these or any other conditions above those listed in the operational section of this specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. DC Operating Conditions (TA = -40 C to + 85 C, VDD = 4.5V to 5.5V unless otherwise specified) Symbol Parameter Min Typ Max Units Notes VDD Main Power Supply 4.5 5.0 5.5 V IDD VDD Supply Current @ SCL = 100 kHz @ SCL = 400 kHz @ SCL = 1 MHz 100 200 400 ISB Standby Current 4 10 A 2 ILI Input Leakage Current ±1 A 3 ILO Output Leakage Current ±1 A 3 VIL Input Low Voltage -0.3 0.3 VDD V VIH Input High Voltage 0.7 VDD VDD + 0.3 V VOL Output Low Voltage @ IOL = 3 mA 0.4 V RIN Input Resistance (WP pin) For VIN = VIL (max) For VIN = VIH (min) VHYS Input Hysteresis 0.05 VDD V 4 Notes 1. SCL toggling between VDD-0.3V and VSS, other inputs VSS or VDD-0.3V. 2. SCL = SDA = VDD. All inputs VSS or VDD. Stop command issued. 3. VIN or VOUT = VSS to VDD. Does not apply to WP pin. 4. This parameter is characterized but not tested. 5. The input pull-down circuit is strong (40K) when the input voltage is below VIL and much weaker (1M) when the input voltage is above VIH.
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 9 of 13 AC Parameters (TA = -40 C to + 85 C, VDD = 4.5V to 5.5V unless otherwise specified) Symbol Parameter Min Max Min Max Min Max Units Notes fSCL SCL Clock Frequency 0 100 0 400 0 1000 kHz 1 tLOW Clock Low Period 4.7 1.3 0.6 s tHIGH Clock High Period 4.0 0.6 0.4 s tAA SCL Low to SDA Data Out Valid 3 0.9 0.55 s tBUF Bus Free Before New Transmission 4.7 1.3 0.5 s tHD:STA Start Condition Hold Time 4.0 0.6 0.25 s tSU:STA Start Condition Setup for Repeated Start 4.7 0.6 0.25 s tHD:DAT Data In Hold Time 0 0 0 ns tSU:DAT Data In Setup Time 250 100 100 ns tR Input Rise Time 1000 300 300 ns 2 tF Input Fall Time 300 300 100 ns 2 tSU:STO Stop Condition Setup 4.0 0.6 0.25 s tDH Data Output Hold (from SCL @ VIL) 0 0 0 ns tSP Noise Suppression Time Constant on SCL, SDA 50 50 50 ns Notes : All SCL specifications as well as start and stop conditions apply to both read and write operations. 1 The speed-related specifications are guaranteed characteristic points from DC to 1 MHz. 2 This parameter is periodically sampled and not 100% tested. Capacitance (TA = 25 C, f=1.0 MHz, VDD = 5V) Symbol Parameter Max Units Notes CI/O Input/Output Capacitance (SDA) 8 pF 1 CIN Input Capacitance 6 pF 1 Notes 1 This parameter is periodically sampled and not 100% tested. Power Cycle Timing VDD min.VDD SDA,SCL tVR tPDtPU tVF Power Cycle Timing (TA = -40C to +85C, VDD = 4.5V to 5.5V unless otherwise specified) Symbol Parameter Min Max Units Notes tPU Power Up (VDD min) to First Access (Start condition) 1 - ms tPD Last Access (Stop condition) to Power Down (VDD min) 0 - s tVR VDD Rise Time 30 - s/V 1 tVF VDD Fall Time 30 - s/V 1 Notes 1. Slope measured at any point on VDD waveform.
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 10 of 13 AC Test Conditions Equivalent AC Load Circuit Input Pulse Levels 0.1 VDD to 0.9 VDD Input rise and fall times 10 ns Input and output timing levels 0.5 VDD Diagram Notes All start and stop timing parameters apply to both read and write cycles. Clock specifications are identical for read and write cycles. Write timing parameters apply to slave address, word address, and write data bits. Functional relationships are illustrated in the relevant data sheet sections. These diagrams illustrate the timing parameters only. Read Bus Timing tSU:SDA Start tR tF Stop Start tBUF tHIG H 1/fSCL tLO W tSP tSP Acknowledge tHD:DAT tSU:DAT tAA tDH SCL SDA Write Bus Timing tSU:STO Start Stop Start Acknowledge tAA tHD:DAT tHD:STA tSU:DAT SCL SDA Data Retention Symbol Parameter Min Max Units Notes TDR @ +85ºC 10 - Years @ +80ºC 19 - Years @ +75ºC 38 - Years 5.5V Output 1700 100 pF
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 11 of 13 Mechanical Drawing 8-pin SOIC (JEDEC Standard MS-012 variation AA) Pin 1 4.90 ±0.10 0.10 0.25 1.35 1.75 0.33 0.51 1.27 0.10 mm 0.25 0.50 0.40 1.27 0.19 0.25 - 8 Recommended PCB Footprint 7.70 0.651.27 2.00 3.70 Refer to JEDEC MS-012 for complete dimensions and notes. All dimensions in millimeters. Legend: XXXXXX= part number, P= package type R=rev code, LLLLLLL= lot code RIC=Ramtron Int‟l Corp, YY=year, WW=work week Example: FM24C16B, “Green” SOIC package, Year 2010, Work Week 49 FM24C16B-G A00002G1 RIC1049 XXXXXXX-P RLLLLLLL RICYYWW
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 12 of 13
Revision History
1.0 11/10/2010 Initial Release 1.1 12/20/2010 Changed VIH (max) to VDD+0.3V. 1.2 2/15/2011 Changed tPU and tVF spec limits. 1.3 7/19/2011 Added ESD ratings. 3.0 1/6/2012 Changed to Production status. Changed tVF spec. Document History Document Title: FM24C16B 16Kb Serial 5V F-RAM Memory Document Number: 001-84450 Revision ECN Orig. of Change Submission Date Description of Change ** 3902082 GVCH 02/25/2013 New Spec *A 3924523 GVCH 03/07/2013 Changed tPU spec value from 10ms to 1ms
FM24C16B - 16Kb 5V I2C F-RAM Document Number: 001-84450 Rev. *A Page 13 of 13 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive cypress.com/go/automotive Clocks & Buffers cypress.com/go/clocks Interface cypress.com/go/interface Lighting & Power Control cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers cypress.com/go/usb PSoC® Solutions psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 5 Cypress Developer Community Community | Forums | Blogs | Video | Training Technical Support cypress.com/go/support RAMTRON is a registered trademark and NoDelay™ is a trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are the property of their respective owners. © Cypress Semi conductor Corporation, 2011 -2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress p roduct. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted n or intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypr ess. Furthermore, Cypress does not authorize its products for use as critical components in lif e-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life -support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. This Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non -exclusive, non -transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the so le purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or re presentation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does no t assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life -support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life -support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agr eement.