DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
460 Watts
Total Output Power: 460 Watts +12 Vdc Stand-by Output Wide Range Input Voltage: 90 - 264 Vac Special FeatureS Active power factor correction EN61000-3-2 harmonic compliance Active AC inrush control 1U X 2U form factor +12 Vdc output +12 Vdc stand-by Hot plug operation N + 1 redundant Active current sharing Built-in cooling fan I2C communication interface bus PMBus compliant EEPROM for FRU data Two years warranty SaFety UL/cUL 60950 (UL Recognized) NEMKO 60950 Cb Certificate and report CE Mark (LVD) Electrical Specifications Input Input ra nge: 90 - 264 Vac Frequency: 47 - 63 Hz, single phase AC Inrush current: 30 Apk maximum inrush current Efficiency: 92% typical at high line 50% load Conducted EMI: FCC Subpart J EN55022 Class A Radiated EMI: FCC Subpart J EN55022 Class A Power factor: 0.99 typical Leakage current: 1.0 mA @ 240 Vac Hold up time: 10 ms minimum Output Main DC voltage: +12.3 V @ 36.0 A Stand-By: +12 V @ 2.3 A Adjustment range: Factory Set Regulation: 11.85 - 12.45 Vdc 11.40 - 12.6 Vdc Overcurrent: +12 Vdc; latches off if overcurrent lasts over 1 second, Trip point 120% - 150% of rated current. Overvoltage: +12 Vdc; 13.6 - 15.0 Vdc +12 Vsb; 13.6 - 15.0 Vdc Turn-on delay: 1 - 1.5 seconds Main output rise time: 10 - 30 mS, monotonic rise Data Sheet
PS_PRESENT (S4): Used to sense the number of power supplies in the system (operational or not) and provide hot plug insertion and removal functionality by controlling main outputs during hot plug insertion and removal by employing following circuitry. When the unit is removed from the system the fast shut down signal quickly turns OFF main outputs and discharges output capacitors. This signal is the shortest gold finger pin on the signal connector to allow for last make, first break configuration. PSOK (S6): Combined indicator of AC input and main 12 V DC output. This is a three level signal to indicate different stages as follows. AC not OK and DC not OK – Signal status shall be LOW (< 0.6 V) AC OK and DC not OK – Signal status shall be LOW (< 0.6 V) AC OK and DC OK – Signal status shall be HIGH (> 3.0 V) AC not OK and DC OK – Signal status shall be Middle Level (Between 2 V and 2.5 V) DC OK threshold is defined as when the 12 V output is greater than 11.5 V. DC not OK threshold is defined as when the 12 V output is less than 11.4 V & greater than 11.3 V. I-Mon (S7): Provides both the load sharing function (as a feedback for output regulation droop function) and 12 V output current information. PS INTERRUPT (S4): The signal behavior in response to certain operating condition changes in the power supply as defined in the Firmware Specification section. This signal shall be pulled up to maximum 5 V logic level external to the PS. PS ON (S8): Required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the main 12 V DC output. When this signal is not pulled low by the system, or left open, the 12 V output is turned off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. Refer to On/Off Timing for timing dia- gram in TRN. When in off or standby condition, the main 12 V DC output will be less than 50 mV with respect to output return. Environmental Specifications Operating temperature: -10 °C to 50 °C Storage temperature: -40 °C to +85 °C Altitude, operating: 10,000 ft. Electromagnetic susceptibility/Input transients: -EN61000-3-2 RoHS & lead-free compliant No tantalum caps. Humidity: 5 to 90% RH, non-condensing Shock and vibration specificatons: Complies with Astec Std. Specifications MTBF (Demonstrated): 500K Hrs at full load, 50 °C
Ordering Information
Model Number Nominal Output Voltage Set Point Set Point Tolerance Total Regulation Minimum Current Maximum Current Output Ripple P/P Over Current Stand-by Air Flow DS460S-3-004 DS460S-3-005 *Overcurrent latches off if overcurrent lasts over 1 second, otherwise it is auto recovery.
EMI GASKET (8X) 3.5 7.6 0.8 (2X) 4.2 198.1 ± 0.6 187.8 70.86 43.2SanAce (40 x 40 x 28 mm FAN) Model No. 9GA0412P3J01 196.9 ± 0.65 39.9± 0.5 11.129.5 ± 0.6 PROGRAMMING WINDOWS (COVERLABEL REMOVED) 136.9 (2X)
0.8 HEMM ING
40.5 REF
0.7 RAMP TO FAN TOP OF FAN TO CHASSIS BOTTOM 9.9 8 25 (2X) 136.9 (6X) 86.4 ± 0.55 7.75 ± 0.65 LATCH(BLACK) 3.2 HANDLE MODEL (TEXT AS ORIENTED) LABEL LOCATION 243.2 43.2 Weight: 1.88 lbs
Output Connector - Power Blades PB1 V o PB2 Vo PB3 Vo PB4 RTN PB5 RTN PB6 RTN PB7 RTN PB8 RTN PB9 Vo PB10 Vo Earth Ground Power Supply Output Card Edge (Top Side) PB5 S1S8 PB4 PB3 PB2 PB1 Power Supply Output Card Edge (Bottom Side) PB6 PB7 PB8 PB9 PB10 S9 S16 Output Connector - Signal Blades S1 VSB S2 VSB S3 Reserved S4 PS INTERRUPT S5 PS PRESENT S6 PSOK S7 I-MON S8 PSON# S9 SCL* S10 SDA S11 GND S12 ADD0 S13 ADD1 S14 ADD2 S15 RTN S16 RTN *Supports I 2C standard mode (100 kHz) only
2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 europe (uK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc. www.artesyn.com DS460S-DS Rev. 08.13.14 Power/Signal Mating Connectors and Pin Types Reference On Power Supply Mating Connector or Equivalent AC Input Connector IEC320-C13 IEC320-C14 Output Connector PCB card edge (0.062”) Molex 459840007 (top mount) Molex 459841122 (bottom mount)