DS3000PE ARTESYN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
High Line: 3000 W Low Line: 1350 W Distributed Power Bulk Front-end Single Ouptut Standard Total Output Power:
3000 W continuous
208 Vac to 264 Vac, 3000 W 1
90 Vac to 140 Vac, 1350 W
3000 W output power High power and narrow form factor 6 units can fit in a 19” inch for a total of 16.2 kW High density design: 24 W/in3 Active Power Factor Correction EN61000-3-2 harmonic compliance Inrush current control 80plus platinum efficiency N+1 or N+N redundant Hot-pluggable Active current sharing Full digital control PMBus compliant Accurate input power reporting Compatible with Artesyn’s universal PMBus GUI Two-year warranty COMPLIANCE Conducted/Radiated EMI EN55022 Class A Limits + 6 dB margin RoHS SAFETY UL/cUL DEMKO+ CB Report EN60950 BSMI CE Mark China CQC Electrical Specifications Input Input voltage range 90-140 Vac, 1350 W 208 to 264 Vac1, 3000 W Frequency 47 Hz to 63 Hz Efficiency 94.0% peak Max input current 17.5 Arms Inrush current 55 Apk Conducted EMI Class A Radiated EMI Class A Power factor >0.97, typical ITHD 10% Leakage current 0.58 mA Hold-up time 11 ms Data Sheet
Ordering Information
DS3000PE-3 Standard Airflow DS3000PE-3-001 Reverse Airflow 1 2700 W output rating at 180 Vac
Main DC Output MIN NOM MAX Nominal setting -0.30% 12 0.30% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 120 mVp-p Output current 2 A4 250 A5 Current sharing Within +/-13.8 A of each other Capacitive loading 1,000 µF 15,000 µf Start-up from AC to output 2100 ms Output rise time 2 ms 60 ms Standby DC Output Nominal setting -1% 12.0 V 1% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 120 mVp-p Output current 0.5 A 4.5 A Current sharing N/A Capacitive loading 47 µF 560 µf Start-up from AC to output 1700 ms Output rise time 2 ms 60 ms Protections Main Output Overcurrent protection2 104% 120% Overvoltage protection1 13.5 V 15.0 V Undervoltage protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output Overcurrent protection4 110% 150% Overvoltage protection3 13.5 V 15.0 V Undervoltage protection 9.6 V 11.0 V
1 Latch mode
2 Autorecovery if the overcurrent is less than 104% and last only for <500 ms.
3 Standby protection is auto-recovery
4 Minimum current for transient load response testing only. Unit is designed to operate and be wtihin regulation range at zero load. 5 Revere airflow model derates to 231.5 A
Control and Status Signals Input Signals PSON Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA PSKIL First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA A0, A1, A2 Addressing pins of the power supply for I2C communications. Refer to the addressing tables below. MIN MAX Internal pull-ups to 3.3V. It is recommended for the system to have pull-ups and decoupling on the address lines for better noise immunity. R = 22 k ohm C = 47 pF VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 4 mA ISINK Current that may be sunk by this pin 4 mA Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 k ohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 k ohm resistor. MIN MAX VIL Output logic level LOW 0.6 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA
Control and Status Signals PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 k ohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 k ohm resistor. MIN MAX VIL Output logic level LOW 0.8 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP , OCP , OTP , and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Output logic level LOW 0.8 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 4 mA ISINK Current that may be sunk by this pin at low state 4 mA BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX ISHARE Voltage Input logic level LOW 7.75 8.25 Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 0.3 ISOURCE Current that may be sourced by this pin 160 mA SCL, SDA Clock, data and addressing signals defined as per I2C requirements. The maximum system side resistor pull-up and decoupling capacitance MIN MAX VL Logic level LOW 0.8 V VH Logic level HIGH 2.0 V 5.0 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. I2C Addressing Table FRU ADDRESSING A2 A1 A0 Address HIGH LOW LOW 0 x A9 HIGH LOW HIGH 0 x AB HIGH HIGH LOW 0 x AD HIGH HIGH HIGH 0 x AF* * Default address when AO and A1 are open PMBus Addressing Address 0 x B8 0 x BA 0 x BC 0 x BE
Firmware Reporting And Monitoring Accuracy Range Output loading 5 to 20% 20 to 50% 50 to 100% Input voltage ±5% Input current ±0.55 A fixed error ±4% Input power ±10 W at < 100 W input ±5% Output voltage ±2% Output current 2.5 A fixed error ±2% Temperature ±5 degC on the operating range EIN ±15% from 10% to 20% load ±5% Fan speed ±250 RPM PMBus YES Remote ON/OFF YES Electrical Specifications LED Indicators AC GOOD LED DC GOOD LED FAULT LED Color GREEN GREEN AMBER No AC input to PSU Off Off Off AC present, STBY ON, main output OFF On Off Off Main output ON On On Off Power supply failure (OVP , OTP , FAN FAULT) Off Off Blinking Timing Specifications Description Min Max Unit Tsb_On Delay from AC being applied to standby output being within regulation 500 2000 ms Tsb_vout Delay from standby output to main output voltage being within regulation 1200 ms Tsb_ACOK Delay from standby output to ACOK assertion 40 ms Tac_on_delay Delay from AC being applied to main output being within regulation 2200 ms Tpwok_on Delay from output voltages within regulation limits to PWOK asserted 100 1200 ms Tacok_delay Delay from loss of AC to assertion of ACOK 250 ms Tpwok_hold-up Delay from loss of AC to deassertion of PWOK 10 ms Tvout_hold-up Delay from loss of AC to main output falling out of regulation 11 ms Tsb_Hold-up Delay from loss of AC to standby output being within regulation 150 ms TPWR_GOOD_Off Delay from deassertion of PWOK to output falling out of regulation 1 ms TPSON_On_Delay Delay from PSON assertion to output being within regulation 350 ms
Vout_main PWOK ACOK Vout_stby AC Input Tsb_On TAC_On_Delay Tsb_Vout TPSON_On_Delay Tsb_Hold-up TPWOK_Hold-up TVout_Hold-up TPWOK_Off TACOK_Delay TPWOK_On Tsb_ACOK Environmental Specifications Operating temperature Full power from 0 to 40 °C, derate output power by 2.5% per °C from 40 °C to 50 °C Operating altitude up to 10,000 feet Operating relative humidity 20% to 80% non-condensing Non-operating temperature -40 to +85 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 30,000 feet Vibration and shock Standard operating/non-operating random vibration/shock ROHS compliance Yes MTBF 400,000 hours Operating life Minimum of 5 years Reliability All electronic component derating analysis and capacitor life calculation is done at 25 degC ambient, maximum rated load, nominal input line voltage.
For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com www.artesyn.com WORLDWIDE OFFICES Americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 Asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. DS3000PE 30Jul2015 Connector Definitions Output Connector Part Number 75555-104 Mating Connector Part Number 75541-104REVB1 or any other Molex recommended part Pin Signal Name Amps per pin1 PB1 RETURN 150 PB2 RETURN 150 PB3 12 V 150 PB4 12 V 150 A1 PWR GOOD N/A A2 PSKILL N/A A3 PRESENT N/A B1 RETURN N/A B2 ISHARE N/A B3 RETURN N/A C1 PS_INTERRUPT N/A C2 RETURN N/A C3 ACOK N/A D1 RETURN N/A D2 PSON N/A D3 RESERVED N/A E1 SDA N/A E2 SCL N/A E3 A0 N/A F1 RESERVED N/A F2 A1 N/A F3 A2 N/A G1 RESERVED N/A G2 RESERVED N/A G3 RESERVED N/A H1 12 VSB 2 H2 12 VSB 2 H3 12 VSB 2