DS1600SPE ARTESYN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
1600 Watts Distributed Power System
Total Output Power:
1600 W continuous at high line
Wide Range Input Voltage: 90 - 264 Vac SPECIAL FEATURES 1600 W output power at high line High power and short form factor 1U power supply High density design: 40 W/in3 Active power factor correction EN61000-3-2 harmonic compliance Inrush current control 80plus platinum efficiency N+1 or N+N redundant Active current sharing Full digital control PMBus compliant Compatible with Artesyn’s universal PMBus GUI Reverse airflow option Two-year warranty COMPLIANCE Class A + 6 dB margin Conducted/ Radiated EMI RoHS compliant SAFETY UL/cUL 60950 (UL Recognized) NEMKO+ CB Report EN60950 EN60950 CE Mark China CQC Electrical Specifications Input Input voltage range 180 to 264 Vac: 1600 W 90 to 140 Vac: 800 W Frequency 47 Hz to 63 Hz Efficiency 94.0% peak Max input current 10.8 Arms Inrush current 55 Apk Conducted EMI Class A Radiated EMI Class A Power factor > 0.9 beginning at 20% load ITHD 10% Leakage current 1.75 mA Hold-up time 10 ms
Ordering Information
Model Number Nominal Main Output Standby Output Airflow Direction DS1600SPE-3 12 V @ 133.3 A 12 V @ 3.5 A Standard (forward) DS1600SPE-3-001 12 V @ 133.3 A 12 V @ 3.5 A Reverse Data Sheet
Main DC Output MIN NOM MAX Nominal setting -0.20% 12 0.20% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range5 11.4 V 12.6 V Output ripple 150 mVp-p Output current 2 A4 133.33 A Current sharing Within +/-5% of full load rating Capacitive loading 2,250 µF 14,000 µF Start-up from AC to output 2,300 ms Output rise time 2 ms 60 ms Standby DC Output Nominal setting -3% 12 3% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 150 mVp-p Adjustment range N/A Output current 0.1 A4 3.5 A Current sharing N/A Capacitive loading 47 µF 1,000 µF Start-up from AC to output 20 ms 2,000 ms Output rise time 2 ms 60 ms Protections Main Output Overcurrent protection2 115% 150% Overvoltage protection1 13.5 V 15.0 V Undervoltage Protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output Overcurrent Protection3 120% 150% Overvoltage Protection1 13.5 V 15.0 V Undervoltage Protection 10.0 V 11.0 V
1 Latch mode
2 Autorecovery if the overcurrent is less than 115% and last only for <500 ms
3 Standby protection is auto-recovery
4 Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load. 5 Maximum step size of 67 A at 0.5A/µs, with a beginning load of 8 A, and 3,350 µF capacitance
Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. System Side pull-up resistor is not required. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA PSKILL_H First break/last mate active HIGH signal which enables/disables the main output. This signal will have to be pulled to ground at the system side. MIN MAX VIL Input logic level LOW. This allows for the power supply to be tunred on 0.8 V VIH Input logic level HIGH. Immediately shuts down the power supply 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 200 mV. Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX VIL Output logic level LOW 0.6 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX VIL Output logic level LOW 0.8 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA
Control and Status Signals Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP , OCP , OTP , and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Output logic level LOW 0.8 V VIH Output logic level HIGH 2.0 V 5.0 V ISOURCE Current that may be sourced by this pin 4 mA ISINK Current that may be sunk by this pin at low state 4 mA BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX ISHARE Voltage Voltage at 100% load, stand-alone unit 7.75 8.25 Voltage at 50% load, stand-alone unit 3.85 4.15 ISOURCE Current that may be sourced by this pin 160 mA SCL, SDA, A0, A1, A2 Clock, data and addressing signals defined as per I2C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 22 pF decoupling capacitor at the system side. MIN MAX VL Logic level LOW 0.8 V VH Logic level HIGH 2.0 V 5.0 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. I2C Addressing Table A2 A1 A0 PMBus (W/R) FRU (W/R) 0 0 0 B0/B1 A0/A1 0 0 1 B2/B3 A2/A3 0 1 0 B4/B5 A4/A5 0 1 1 B6/B7 A6/A7 1 0 0 B8/B9 A8/A9 1 0 1 BA/BB AA/AB 1 1 0 BC/BD AC/AD 1 1 1 BE/BF AE/AF
Firmware Reporting And Monitoring Accuracy Range Output loading 8 to 20% 20% to 50% 50% to 100% Input voltage ±5% Input current ±0.55A ±5% Input power ±5W at <125 W input power ±1.25% Output voltage ±2% Output current ±1.2 A fixed error ±3% Temperature ±5 degC on the operating range EIN ±15% from 10% to 20% load ±5% Fan speed ±250 RPM PMBus YES Remote ON/OFF YES Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No AC input to PSU Off Main output ON Solid GREEN Standby mode and Power supply failure (OCP , OVP , OTP , FAN FAULT) Blinking AMBER
Tsb_On Delay from AC being applied to standby output being within regulation 20 2000 ms Tsb_ACOK Delay from standby output to ACOK assertion See note below 20 ms Tsb_Vout Delay from standby output to main output voltage being within regulation 300 ms TAC_On_Delay Delay from AC being applied to main output being within regulation 2300 ms TPWOK_On Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms TACOK_Delay Delay from loss of AC to assertion of ACOK 7 ms TPWOK_Hold-up Delay from loss of AC to deassertion of PWOK 10 ms TVout_Hold-up Delay from loss of AC to main output being within regulation 11 ms Tsb_Hold-up Delay from loss of AC to standby output being within regulation 150 ms TPWR_GOOD_Off Delay from deassertion of PWOK to output falling out of regulation 1 ms TPSON_On_Delay Delay from PSON assertion to output being within regulation 150 ms TPWOK_Low Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU N/A N/A Note: Tsb_hold-up: tested at 1A load on standby output T sb_ACOK: ACOK can assert earlier than the standby output Timing Diagram PSON Vout_main PWOK ACOK Vout_stby AC Input Tsb_On TAC_On_Delay Tsb_Vout TPSON_On_Delay Tsb_Hold-up TPWOK_Hold-up TVout_Hold-up TPWOK_Off TACOK_Delay TPWOK_On Tsb_ACOK
B C B A A C DIM AND TOL NEED TO BE HELD AT THE EDGE OF THE STANDOFF LOCATIONS ONLY. 6±0.3 38.5+0.9 -0.5 40.25±0.7 40.2±0.5 86.3±0.5 196.5 (4) 9.3±0.4 8.8±0.5 191.1±0.5 MODEL AIRFLOW DIRECTION DS1600SPE-3 FORWARD DS1600SPE-3-001 REVERSE (14.8)
For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com www.artesyn.com WORLDWIDE OFFICES Americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 Asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1600SPE 01Jul2016 Connector Definitions Output Connector Part Number Card-edge Mating Connector Part Number FCI 10107844-002LF or any equivalent P21-28P29-P36 P19/20 ... S24 S13 Power Supply Output Card Edge (Bottom Side) P1-P8 P9-P18 .. S1 S12 Power Supply Output Card Edge (Top Side) Output Connector Pin Configuration S1 PS_PRESENT S13 PS_ON_L S2 A1 S14 PSKILL_H S3 A0 S15 RESERVED S4 PWR_GOOD (PWOK) S16 RTN S5 ACOK (AC Input Present) S17 SDA S6 RTN S18 RTN S7 I_SHARE S19 SCL S8 RESERVED S20 RTN S9 PS_INTERRUPT_L S21 REMOTE SENSE - S10 RETURN S22 RTN S11 RESERVED S23 REMOTE SENSE + S12 RESERVED S24 A2 P1-P8 +12VOUT P19-P20 +VSB P9-P18 RETURN P21-P28 RETURN P29-P36 +12VOUT Environmental Specifications Operating temperature Ds1600SPE-3: 1600W from 0 to 50 °C, can operate up to 65°C at 2% derated power for every °C above 50°C DS1600SPE-3-001: 1600W from 0 to 40°C, can operate up to 60°C at 1% derated power for every °C above 40°C Operating altitude up to 16,400 feet, derated after 10,000 feet Operating relative humidity 5% to 95% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity 5% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating and non-operating random shock and vibration ROHS compliance Yes MTBF 1,100,000 hours using Bell Core TR-332, issue 6 specification, Method 1 Case 3 at 25 °C ambient at full load. Operating life Minimum of 5 years