DS1100SLPE-3-001 ARTESYN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
1100 Watts Distributed Power System
Total Output Power:
1100 W continuous
Wide Input Voltage: 90 to 264 Vac SPECIAL FEATURES 1100 W output power High-power and short form factor 1U power supply High-density design: 26 W/in3 Active Power Factor Correction EN61000-3-2 harmonic compliance Inrush current control 80plus Platinum Efficiency N+1 or N+N Redundant Hot-pluggable Active current sharing Full digital control PMBus compliant Accurate input power reporting Compatible with Artesyn’s Universal PMBus GUI Reverse airflow option Two-year warranty COMPLIANCE EMI Conducted/Radiated Class A Limits + 6 dB margin EN61000-4 Electromagnetic compatibility ROHS 6/6 SAFETY UL/cUL 60950 (UL Recognized) DEMKO+ CB Report EN60950 CE Mark China CCC BSMI Electrical Specifications Input Input range 90 - 264 Vac Frequency 47 Hz to 63 Hz Efficiency 94.0% peak Max input current 14.5 Arms Inrush current 55 Apk Conducted EMI Class A +6 dB margin Radiated EMI Class A +6 dB margin Power factor > 0.9 beginning at 20% load ITHD 10% Leakage current 1.75 mA Hold-up time 16 ms at full load Output Main DC Output Standby DC Output MIN NOM MAX MIN NOM MAX Nominal setting -1% 12 +1% -1% 3.3 1% Dynamic load regulation range 11.64 V 12.36 V 3.14 V 3.46 V Output ripple 180 mVp-p 45 mVp-p Output current 0.5 A1 90.0 A 0.1 A 3.0 A Current sharing Within ±5.625A of each other from 25% to 100% load N/A Capacitive loading 500 uF 11,000 uF 100 uF 680 uF Start-up from AC to output 2200 ms 1700 ms Output rise time 5 ms 50 ms 2 ms 60 ms Note: Outputs shall be isolated from the chassis ground by at least 50 V. 1Minimum starting current for transient load response testing only. Unit is designed to operate and be within output regulation at zero load. Data Sheet
Overcurrent protection2 107% 130% Overvoltage protection1 13.5 V 15.0 V Overtemperature protection Yes, autorecovery Fan fault protection Yes Standby Output Over-current protection3: 110% 150% Over-voltage protection1 3.6 V 3.9 V
1 Latch mode
2 No shutdown if the overcurrentis within the range and does notlast for more than 200 ms, otherwise latch will occur
3 Autorecovery
Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 3.6 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA PSKILL_H First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 3.6 V ISOURCE Current that may be sourced by this pin 2 mA ISINK Current that may be sunk by this pin at low state 0.5 mA VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 100 mV
Ordering Information
Model Number Nominal Main Output Standby Output Airflow Direction DS1100SLPE-3 12 V 3.3 V @ 3 A Std (forward) DS1100SLPE-3-001 12 V 3.3 V @ 3 A Reverse1 1 Derating may apply. I2C Addressing A1 Pin A0 Pin PMBus (w/r) 0 0 B0/B1 0 1 B2/B3 1 0 B4/B5 1 1 B6/B7
Control and Status Signals Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 10 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be onnected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX VIL Input logic level LOW 0.6 V VIH Input logic level HIGH 2.0 V 3.6 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 10 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 3.6 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP , OCP , OTP , and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH 2.0 V 3.6 V ISOURCE Current that may be sourced by this pin 4 mA ISINK Current that may be sunk by this pin at low state 4 mA
Control and Status Signals BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies con# gured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX ISHARE Voltage Input logic level LOW 7.75 8.25 Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 1.0 ISOURCE Current that may be sourced by this pin 160 mA SCL, SDA Clock and data signals de# ned as per I2C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. VL Input logic level LOW 0.8 V VH Input logic level HIGH 2.0 V 3.6 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED Fail LED Color Green Amber/Green No input to PSU Off Off Input present, STBY ON, main output OFF On Blinking Amber, at least 1 Hz Main output ON On green Power supply warning (hi-temp) On Blinking Amber/Green, at 2:1 ratio, at least 1 Hz Power supply warning (slow fan) Off Blinking Amber/Green, at 1:1 ratio, at least 1Hz Power supply failure (OVP , OTP , FAN FAULT) On Amber Firmware Reporting And Monitoring Accuracy Range Output loading <10% 10% to 20% 20% to 100% Input voltage ±5% Input current ±1 A fixed error ±10% ±5% Input power 30 W fixed error up to 120 W ±15% ±10% Output voltage ±5% ±2% Output current 0.8 A fixed error ±15% ±5% Temperature ±5 °C Fan speed Actual ±250 RPM PMBus YES Remote ON/OFF YES
Tsb_On Delay from AC being applied to standby output being within regulation 2500 ms Tsb_ACOK Delay from standby output to ACOK assertion 1500 ms Tsb_Vout Delay from standby output to main output voltage being within regulation 1000 ms TAC_On_Delay Delay from AC being applied to main output being within regulation 3000 ms TPWR_GOOD_On Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms TACOK_Delay Delay from loss of AC to assertion of ACOK 20 ms TPWR_GOOD_Hold-up Delay from loss of AC to deassertion of PWOK 5 ms TVout_Hold-up Delay from loss of AC to main output being within regulation 16 ms Tsb_Hold-up Delay from loss of AC to standby output being within regulation 25 ms TPWR_GOOD_Off Delay from deassertion of PWOK to output falling out of regulation 1 700 ms TPSON_On_Delay Delay from PSON assertion to output being within regulation 400 ms Timing Diagram PSON Vout_main PWOK ACOK Vout_stby AC Input Tsb_On TAC_On_Delay Tsb_Vout TPSON_On_Delay Tsb_Hold-up TPWOK_Hold-up TVout_Hold-up TPWOK_Off TACOK_Delay TPWOK_On Tsb_ACOK
Output Connector Part Number TEI 2-1926736-2 Mating Connector Part Number TEI 2-1926739-5, 1892787-6 or equivalent Output Connector Pin Configuration A1 3.3 VSB Standby Output B1 3.3 VSB Standby Output C1 3.3 VSB Standby Output D1 3.3 VSB Standby Output E1 3.3 VSB Standby Output A2 SGND Signal Ground B2 SGND Signal Ground C2 Reserved D2 Reserved E2 Reserved A3 A2/A_Select Optional address line B3 A0 I2C Address C3 SDA I2C Data D3 -Remote_Sense Wire drop compensation E3 +Remote_Sense Wire drop compensation A4 SCL I2C Clock B4 PSON_L Enable/Inhibit C4 PS_INTERRUPT_L Alert for failure D4 A1 I2C Address E4 ACOK Input indicator A5 PSKILL_L First break/lastmate pin B5 ISHARE Current share bus C5 PWOK Output indicator D5 Reserved E5 PS_PRESENT_L Power supply present P1-P5 +12 V Return Main output return contact P6-P10 12 V Main output power contact
For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com www.artesyn.com WORLDWIDE OFFICES Americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 Asia (HK) 14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. DS1100SLPE 29Jul2015 Environmental Specifications Operating temperature DS1100SLPE-3 DS1100SLPE-3-001 Full power at -5 to 55 °C, can operate up to 65 °C at 660 W derated power Full power at -5 to 45 °C, can operate up to 55 °C at 660 W derated power Operating altitude up to 10,000 feet Operating relative humidity 20% to 90% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating random shock and vibration ROHS compliance Yes MTBF >500,000 hours using Telcordia Issue 2, Method 1 Case 1 at 40 °C ambient at full load. Operating life Minimum of 7 years at typical operating conditions Reliability All electronic component derating analysis and capacitor life calculation is done at 40 degC ambient, 80% of maximum rated load, nominal input line voltage.