C9851 CYPRESS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 14
Technical content
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 1 of 14 http://www.cypress.com PRELIMINARY C9851 Product Features
- Six pairs of current referenced differential clocks
- Two 3V 180 ° displaced Mref clocks for DRCG
- One 66.6 MHz reference output
- One 14.318 MHz reference output
- Select logic for Differential Swing Control, Test mode, Hi-Z, Power-down, Spread spectrum, and limited frequency select
- Cypress Spread Spectrum for EMI reduction
- 48 Pin SSOP Package Product Description This device provides the necessary clocks for a differential host bus system in multi-processor servers and workstations. It also generates a 66.6MHz hub clock for interfacing with a complimentary part, the Cypress B9852. The 2 Mref clock outputs are 180 degrees out of phase and are used for interfacing with the Direct Rambus Clock Generator (DRCG), C9820, C9821, or C9822. This device integrates the Cypress spread spectrum technology for optimum EMI reduction. Frequency Selection Table SEL 100/133 SELA SELB CPU(1:6), CPU#(1:6) 3VMref, 3Vmref_b 3V66 REF 0 0 0 100 MHz 50 MHz 66.67 MHz 14.318 MHz 0 0 1 100 MHz Low Low Low 0 1 0 200 MHz 50 MHz 66.67 MHz 14.318 MHz 0 1 1 Hi-Z Hi-Z Hi-Z Hi-Z 1 0 0 133.3 MHz 66.67 MHz 66.67 MHz 14.318 MHz 1 0 1 25 MHz 50 MHz 66.67 MHz 14.318 MHz 1 1 0 200 MHz 66.7 MHz 66.67 MHz 14.318 MHz 1 1 1 REF/2 REF/4 REF REF Block Diagram Table 1 Pin Configuration VSSR Ref VDDR XIN XOUT VSSR VDDM 3VMref 3VMref_b VSSM VDD VSS VDDL 3V66 VSSL SEL100/133 MultSel0 MultSel1 VDDA VSSA SelA SelB Spread# PwrDwn# VDD VSS VDDC CPU1 CPU1# VSSC CPU2 CPU2# VDDC CPU3 CPU3# VSSC CPU4 CPU4# VDDC CPU5 CPU5# VSSC CPU6 CPU6# VDDC I_Ref VSSA VDDA OSC VCO I Control VDDA I_Ref VSSI VDDR VSSR REF CPU (1:6) CPU (1:6)# VDDM 3VMRef 3VMRef_b VSSM VDDL 3V66 VSSL Spread# SelA SelB SEL100/133 XOUT XIN MultSel(0:1) PwrDwn#
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 2 of 14 http://www.cypress.com PRELIMINARY C9851 Pin Description PIN No. Pin Name I/O Description 8 3VMref O Output clock for driving the DRCG device. See table 1, page1 for frequency selection. 9 3VMref_b O Output clock for driving the DRCG device. See table 1, page1 for frequency selection. It is 180 degrees out of phase (inverted) from the 3VMref clock. 23 Spread# PU When asserted low, this pin invokes Spread Spectrum functionality. Spread spectrum is applicable to CPU(1:6), CPU(1:6)#, 3VMref, 3VMref_b, and 3V66 clocks. This pin has a 250KΩ internal Pull-up. 45,42,39,36, 33,30 CPU(1:6) 44,41,38,35, 32,29 CPU(1:6)# O Differential host clock outputs. These outputs are used in pairs, (CPU1-1#, CPU2-2#, CPU3-3#, CPU4-4#, CPU5-5#, and CPU6-6#) for differential clocking of the host bus. CPU(1:6)# are 180 degrees out of phase with their complements, CPU(1:6). See table 1, page 1 for frequency selection.
27 I_Ref P This pin establishes the reference current for the internal current steering buffers of the
CPU clocks. A resistor is connected from this pin to ground to set the value of this current. See applications data on page 9 of this data sheet for details. 14 3V66 O Fixed 66.67 MHz clock output for driving the IMI B9852 buffer device.
24 PwrDwn# PU When asserted low, this pin Invokes power-down mode by shutting off all the clocks,
disabling all internal circuitry, and shutting down the crystal oscillator. The 3VMref, 3VMref_B, 3V66, REF and CPU clocks are driven low during this condition. It has a 250KΩ internal Pull-up. 22, 21 SelA, SelB PD Input select pins. See table 1, page 1. Each pin has a 250KΩ internal Pull-down 16 SEL100/133 PU Input select pin. See table 1, page 1. It has a 250KΩ internal Pull-up 5X O U T O Crystal Buffer output pin. Connects to a crystal only. When an external signal other than a crystal is used or when in Test mode, this pin is kept unconnected. 4X I N I Crystal Buffer input pin. Connects to a crystal, or an external single ended input clock signal. 2 REF O A buffered output clock of the signal applied at Xin. Typically, 14.31818MHz. 18, 17 MultSel (0,1) I These input select pins configure the LOH current (and thus the VOH swing amplitude) of the CPU clock output pairs. Each pin has a 250KΩ internal Pull-up. See the table 5 for current and resistor values. 3 VDDR P 3.3V power supply pins for Ref clock and crystal buffer. 46,40,34,28 VDDC P 3.3V power supply pins for CPU(1:6) / CPU(1:6)# outputs. 11, 48 VDD P 3.3V power supply pins for common supply to the core. 13 VDDL P 3.3V power supply pins for 3V66 output. 19, 25 VDDA P 3.3V power supply pins for internal current reference circuitry and internal PLL. 7 VDDM P 3.3V power supply pin for 3Vmref and 3Vmref_b outputs 1, 6 VSSR P Ground pins for the Ref clock and crystal buffer. 31, 37, 43 VSSC P Ground pins for the CPU(1:6)/CPU(1:6)# outputs. 12, 47 VSS P Ground pins for common supply to the core. 15 VSSL P Ground pin for the 3V66 output. 20, 26 VSSA P Ground pin for internal current reference circuitry and internal PLL. 10 VSSM P Ground pin for 3Vmref and 3Vmref_b outputs. Note: Definition of I/O column pneumonic on pin description table above: I = Input pin, O = output pin, P = power supply pin, PU = This indicated that a bi-directional pin contains a device internal p ull-up resistor. This will insure that this pin of the device will be seen by the internal logic as a logic 1 level. Likewise pins wit h a PD designation are guaranteed to be seen as a logic 0 level if no external level setting circuitry is present at power up.
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 3 of 14 http://www.cypress.com PRELIMINARY C9851 Maximum Ratings Maximum Input Voltage Relative to VSS: VSS - 0.5V Maximum Input Voltage Relative to VSS: VDD + 0.7V Storage Temperature: -65ºC to + 150ºC Operating Temperature: 0ºC to +70ºC Maximum ESD protection 2000V Maximum Power Supply: 5.5V This device contains circuitry to protect the inputs against damage due to high static voltages or electric field; however, precautions should be taken to avoid application of any voltage higher than the maximum rated voltages to this circuit. For proper operation, Vin and Vout should be constrained to the range: VSS<(Vin or Vout)<VDD Unused inputs must always be tied to an appropriate logic voltage level (either VSS or VDD). DC Parameters (VDDI = VDD = VDDR = VDDL = VDDM = VDDC = 3.3V ±5%, TA = 0°C to +70°C) Characteristic Symbol Min Typ Max Units Conditions Input Low Voltage VIL1 - - 0.8 Vdc Input High Voltage VIH1 2.0 - - Vdc Note 1 Input Low Current (@Vin = VSS) IIL -16 -4 µA Input High Current (@Vin = VDD) IIH 0 5 µA For internal Pull up resistors, Note 1 and Note 2 Input Low Current (@Vin = VSS) IIL 0 - µA Input High Current (@Vin = VDD) IIH 4 16 µA For internal Pull down resistors, Note 1 and Note 2 Tri-State leakage Current Ioz - - 10 µA Static Supply Current Idd - - 30 mA PwrDwn=Low Dynamic Supply Current Isdd - - 200 mA 133 MHz CPU, Note 3 Input pin capacitance Cin - - 5 pF Output pin capacitance Cout - - 6 pF Pin Inductance Lpin - - 7 nH Crystal pin capacitance Cxtal 34 36 38 pF Measured from Pin to Ground. See crystal specification section presented later in this data sheet. Crystal Startup time Txs - - 40 µS From Stable 3.3V power supply. Internal Pull-up and Pull- down resistor value Rpi 200 250 500 KΩ Note1: Applicable to input signals: Sel100/133, Sel(A:B)), Spread#, PWRDN#, MultSel(0:1) Note2: Although internal pull-up or Pull-Down resistors have a typical value of 250K, this value may vary between 200K and 500K. Note3: All outputs loaded as per the maximum capacitive table in this data sheet.
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 4 of 14 http://www.cypress.com PRELIMINARY C9851 AC Parameters (VDDI = VDD = VDDR = VDDL = VDDM = VDDC = 3.3V ±5%, TA = 0°C to +70°C)
133 MHz Host 100 MHz Host
Symbol Parameter Min Max Min Max Units Notes TPeriod CPU[(1:6), (1:6)#] period - 7.35 7.65 9.85 10.2 nS 1, 2 Tr / Tf CPU[(1:6), (1:6)#] rise and fall times 175 450 175 450 pS 2, 3 TSKEW1 skew from any CPU pair to any CPU pair - 150 - 150 pS 2, 4, 5 TSKEW2 skew from package to package - 100 - 100 pS 2, 4, 5 TCCJ CPU[(1:6), (1:6)#] Cycle to Cycle Jitter - 150 - 150 pS 2, 4, 5 Vover CPU[(1:6), (1:6)#] Overshoot Voh+0.2 Voh+0.2 V 2,10 Vunder CPU[(1:6), (1:6)#] Undershoot -0.2 -0.2 V 2, 10 Vcrossover CPU(1:6) to CPU(1:6)# crossover point 45%Voh 55%Voh 45%Voh 55%Voh V 2, 4 Tduty Duty Cycle 45 55 45 55 % 2, 4 TPeriod 3V(MREF, MREF_B) period 15.0 15.3 20.0 20.4 nS 4, 5 THIGH 3V(MREF, MREF_B) high time 5.25 - 7.5 - nS 2, 6 TLOW 3V(MREF, MREF_B) low time 5.05 - 7.3 - nS 2, 7 Tr / Tf 3V(MREF, MREF_B) rise and fall times 0.4 1.6 0.4 1.6 nS 2, 3 TSKEW 3VMREF to 3VMREF_B skew - 250 - 250 pS 2, 4, 5, 11 TCCJ 3V(MREF, MREF_B) Cycle to Cycle Jitter - 250 - 250 pS 2, 4, 5 Tduty Duty Cycle 45 55 45 55 % 2, 4 TPeriod 3V66 period 15.0 16.0 15.0 15.2 nS 1, 2, 4 THIGH 3V66 high time 5.25 - 5.25 - nS 2,6 TLOW 3V66 low time 5.05 - 5.05 - nS 2, 7 Tr / Tf 3V66 rise and fall times 0.5 2.0 0.5 2.0 nS 2, 3 TCCJ 3V66 Cycle to Cycle Jitter - 300 - 300 pS 2, 4, 5 Tduty Duty Cycle 45 55 45 55 % 2, 4 TPeriod REF period 69.8413 71.0 69.8413 71.0 nS 1, 2, 4 Tr / Tf REF rise and fall times 1.0 4.0 1.0 4.0 nS 2, 3 TCCJ REFCycle to Cycle Jitter - 1000 - 1000 pS 2, 4 Tduty Duty Cycle 45 55 45 55 % 2, 4 tpZL, tpZH Output enable delay (all outputs) 1.0 10.0 1.0 10.0 nS 9 tpLZ, tpZH Output disable delay (all outputs) 1.0 10.0 1.0 10.0 nS 9 tstable All clock Stabilization from power-up 3 3 mS Group Limits and Parameters (applicable to all settings: Sel133/100# = x) continued Note 1: This parameter is measured at the crossing points of the differential signals, and acquired as an average over 1uS duration, with a crystal center frequency of 14.31818MHz Note 2: All outputs loaded as per table 2 below. Note 3: Probes are placed on the pins, and measurements are acquired between 0.4V and 2.4V for 3.3V signals and at 20% and 80% for CPU[(1:6), (1:6)#] signals. (see Figs.7A & 7B) Note 4: Probes are placed on the pins, and measurements are acquired at 1.5V for 3.3V signals and at crossing points for CPU clocks (see Figs.7A & 7B). Note 5: This measurement is applicable with Spread ON or Spread OFF. Note 6: Probes are placed on the pins, and measurements are acquired at 2.4V (see Figs. 7A & 7B) Note 7: Probes are placed on the pins, and measurements are acquired at 0.4V. (see Figs. 7A & 7B) Note 9: As this function is available through SEL(A,B), therefore, the time specified is guaranteed by design. Note 10: Determined as a fraction of 2*(Trp-Trn) / (Trp+Trn) where Trp is a rising edge and Trn is an intersecting falling edge. Note 11: 3VMref and 3VMref_b are 180 degrees out of phase, therefore, the skew is measured between the rising edge of one and the falling edge of the other.
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 5 of 14 http://www.cypress.com PRELIMINARY C9851 Group Limits and Parameters (applicable to all settings: Sel133/100# = x) (Continued) Output name Max Load 3VMref, 3VMref_b 30 pF REF 20 pF 3V66 30 pF Table 2. Lumped Test Load Configurations The following shows lumped test load configurations for the differential Host Clock Outputs. (MULTsel1 = 0, MULTsel0 = 1) Fig.1A Test Nodes RpRs Rs 49.9ohm 49.9ohm Rp 33.2ohm 33.2ohm
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 6 of 14 http://www.cypress.com PRELIMINARY C9851 Lumped Test Load Configurations (Cont.) Fig. 1B Spread Spectrum Clock Generation (SSCG) Spread Spectrum is a modulation technique applied here for maximum efficiency in minimizing Electro-Magnetic Interference radiation generated from repetitive digital signals mainly clocks. A clock accumulates EM energy at the center frequency it is generating. Spread Spectrum distributes this energy over a small frequency bandwidth therefore spreading the same amount of energy over a spectrum. This technique is achieved by modulating the clock down from (Fig.2) its resting frequency by a certain percentage (which also determines the energy distribution bandwidth). The default of the device at power up keeps the Spread Spectrum disabled, therefore, in order to enable this function pin23, Spread#, must be connect to ground (a low state.). See table 3 for Spread bandwidth description. In Down Spread mode the center frequency is shifted down from its rested (non-spread) value by -0.25%. (ex.: assuming the center frequency is 100MHz in non-spread mode; when down spread is enabled, the center frequency shifts to 99.75MHz.). In Center Spread mode, the Center frequency remains the same as in the non-spread mode. Probe Output under Test Load Cap 2.4V 0.4V 3.3V Tr Tf 1.5V 3.3V signals tDC - -
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 7 of 14 http://www.cypress.com PRELIMINARY C9851 Spread Spectrum Clock Generation (SSCG) (Cont.) Down Spread Fig. 2 Spectrum Spreading Selection Table Unspread Spread Spectrum Parameter Frequency in MHz Down Spreading F Min (MHz) F Center (MHz) F Max (MHz) Spread (%) 100 99.5 99.75 100 - 0.5% 133.3 132.66 132.67 133 - 0.5% Table 3.
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 8 of 14 http://www.cypress.com PRELIMINARY C9851 Power Management Functions Host Swing Select Functions MultSel0 MultSel1 Board Target Trace/TermZ Reference Rr, Iref = Vdd/(3*Rr) Note2 Output Current Voh @Z, Iref = 2.32mA 0 0 60 Ohms Rf = 475 1%, Iref = 2.32mA Ioh = 5*Iref 0.7V @ 60 0 0 50 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 5*Iref 0.59V @ 50 0 1 60 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 6*Iref 0.85V @ 60 0 1 50 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 6*Iref 0.71V @ 50 1 0 60 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 4*Iref 0.56V @ 60 1 0 50 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 4*Iref 0.47V @ 50 1 1 60 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 7*Iref 0.99V @ 60 1 1 50 Ohms Rr = 475 1%, Iref = 2.32mA Ioh = 7*Iref 0.82V @ 50 Note1: The entries in boldface are the primary system configurations of interest. The outputs should be optimized for these configurations. Note2: Rr refers to the resistance placed in series with the Iref input and Vss. Table 4
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 9 of 14 http://www.cypress.com PRELIMINARY C9851 Buffer Characteristics Current Mode CPU Clock Buffer Characteristics The current mode output buffer detail and current reference circuit details are contained elsewhere in this datasheet. The following parameters are used to specify output buffer characteristics: 1. Output impedance of the current mode buffer circuit - Ro (see Figure 3). 2. Minimum and maximum required voltage operation range of the circuit – Vop (see Figure 3). 3. Series resistance in the buffer circuit – Ros (see Figure 3). 4. Current accuracy at given configuration into nominal test load for given configuration. Figure 3 Host Clock (HCSL) Buffer Characteristics Characteristic Minimum Maximum Ro 3000 Ohms (recommended) N/A Ros Unspecified Unspecified Vout N/A 1.2 Volt Iout is selectable depending on implementation. The parameters above apply to all configurations. Vout is the voltage at the pin of the device. The various output current configurations are shown in the host swing select functions table. For all configurations, the deviation from the expected output current is +/- 7% as shown in the table current accuracy (page 12). 1.2V0V Iout Iout Ros Ro VDD3 (3.3V +/- 5%) Vout = 1.2V max Vout
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 10 of 14 http://www.cypress.com PRELIMINARY C9851 Current Accuracy Conditions Configuration Load Min Max Iout VDD = nominal (3.30V) All combinations of M0, M1 and Rr shown in host Swing Select Function Table 5, p. 8 Nominal test load for given configuration -7% Inom + 7% Inom Iout VDD = 3.30 +/- 5% All combinations of M0, m1 and Rr shown in Host Swing Select Function Table 5, p. 8 Nominal test load for given configuration -12% Inom + 12% Inom Note: Inom refers to the expected current based on the configuration of the device. Buffer Characteristics for REF Characteristic Symbol Min Typ Max Units Conditions Pull-Up Current Min IOH min -12 -53 mA VOH=VDDmin-0.5V (2.64V) Pull-Up Current Max IOH max -27 -92 mA VOH=VDDmin/2 (1.56V) Pull-Down Current Min IOL min 92 7 m A V O L = 0 . 4 V Pull-Down Current Max IOL max 26 79 mA VOL=VDDmin/2 (1.56V) Buffer Characteristics for 3V66, Mref, Mref_b Characteristic Symbol Min Typ Max Units Conditions Pull-Up Current Min IOH min -11 -83 mA VOH=VDD-0.5V (2.64V) Pull-Up Current Max IOH max -30 -184 mA V OH=VDD/2 (1.56V) Pull-Down Current Min IOL min 93 8 m A V O L = 0 . 4 V Pull-Down Current Max IOL max 28 148 mA VOL=VDD/2 (1.56V) 3.3V Output Rise Edge Rate Trh 1/1 - 4/1 V/nS 3.3V +/- 5% @ 0.4V – 2.4 V 3.3V Output Fall Edge Rate Tfh 1/1 - 4/1 V/nS 3.3V +/- 5% @ 2.4V – 0.4 V
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 11 of 14 http://www.cypress.com PRELIMINARY C9851 Suggested Oscillator Crystal Parameters Characteristic Symbol Min Typ Max Units Conditions Frequency F o 14.17 14.31818 14.46 MHz Tolerance T C - - +/-100 PPM Note 1 Frequency Stability T S - - +/- 100 PPM Stability (T A -10 to +60C) Note 1 Operating Mode - - - - Parallel Resonant, Note 1 Load Capacitance C XTAL - 20 - pF The crystal’s rated load. Note 1 Effective Series Resistance (ESR) RESR - 40 - Ohms Note 2 Note1: For best performance and accurate frequencies from this device, It is recommended but not mandatory that the chosen crystal meets or exceeds these specifications Note 2: Larger values may cause this device to exhibit oscillator startup problems To obtain the maximum accuracy, the total circuit loading capacitance should be equal to CXTAL. This loading capacitance is the effective capacitance across the crystal pins and includes the clock generating device pin capacitance (CFTG), any circuit trace capacitance (CPCB), and any onboard discrete load capacitance (CDISC). The following formula and schematic illustrates the application of the loading specification of a crystal (CXTAL)for a design. CL = (CXINPCB + CXINFTG + CXINDISC) X (CXOUTPCB + CXOUTFTG + CXOUTDISC) (CXINPCB + CXINFTG + CXINDISC) + (CXOUTPCB + CXOUTFTG + COUTDISC) Where: CXTAL = the load rating of the crystal CXOUTFTG = the clock generators XIN pin effective device internal capacitance to ground CXOUTFTG = the clock generators XOUT pin effective device internal capacitance to ground CXINPCB = the effective capacitance to ground of the crystal to device PCB trace CXOUTPCB = the effective capacitance to ground of the crystal to device PCB trace CXINDISC = any discrete capacitance that is placed between the XIN pin and ground CXOUTDISC = any discrete capacitance that is placed between the XOUT pin and ground CXINPCB CXOUTPCB CXOUTDISC CXINDISC CXINFTG CXOUTFTG XIN XOUT Clock Generator As an example, and using this formula for this datasheet’s device, a design that has no discrete loading capacitors (CDISC) and each of the crystal to device PCB traces has a capacitance (CPCB) to ground of 4pF (typical value) would calculate as: CL = (4pF + 36pF + 0pF) X (4pF + 36pF + 0pF) = 40 X 40 = 1600 = 20pF (4pF + 36pF + 0pF) + (4pF + 36pF + 0pF) 40 + 40 80 Therefore to obtain output frequencies that are as close to this data sheets specified values as possible, in this design example, you should specify a parallel cut crystal that is designed to work into a load of 20pF
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 12 of 14 http://www.cypress.com PRELIMINARY C9851 Package Drawing and Dimensions (48 Pin TSSOP)
48 Pin TSSOP Outline Dimensions
SYMBOL MIN NOM MAX MIN NOM MAX A1 0.002 - 0.006 0.05 - 0.15 B 0.007 - 0.011 0.17 - 0.27 C 0.004 - 0.008 0.09 - 0.20 e 0.02 BSC 0.50 BSC a 0º - 8º 0º - 8º
48 Pin SSOP Outline Dimensions
SYMBOL MIN NOM MAX MIN NOM MAX A2 0.088 - 0.092 2.24 - 2.34 B 0.008 - 0.0135 0.203 - 0.343 C 0.005 - 0.010 0.127 - 0.254 e 0.025 BSC 0.635 BSC H 0.395 - 0.420 10.03 - 10.67 L 0.020 - 0.040 0.508 - 1.016 a 0º - 8º 0º - 8º a B e A D E H L C
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. ** 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 13 of 14 http://www.cypress.com PRELIMINARY C9851
Ordering Information
Part Number Package Type Production Flow C9851BY 48 Pin SSOP Commercial, 0ºC to +70ºC C9851BT 48 Pin TSSOP Commercial, 0ºC to +70ºC Marking: Example: Cypress C9851 Date Code, Lot # C9851BY Package Y = SSOP T = TSSOP Revision Device Number Notice Cypress Semiconductor Corporation reserves the right to make changes to its products in order to improve design, performance or reliability. Cypress Semiconductor Corporation assumes no responsibility for the use of its products in life supporting and medical applications where the failure or malfunction of the product could cause failure of the life supporting and medical systems. Products are not authorized for use in such applications unless a written approval is requested by the manufacturer and an approval is given in writing by Cypress Semiconductor Corporation for the use of its products in the life supporting and medical applications.
Clock Generator for Pentium III Server and Workstation Applications Cypress Semiconductor Corporation 525 Los Coches St. Document#: 38-07068 Rev. 05/04/2001 Milpitas, CA 95035. Tel: 408-263-6300, Fax: 408-263-6571 Page 14 of 14 http://www.cypress.com PRELIMINARY C9851 Document Title: C9851 Clock Generator for Pentium®III Server and Workstation Applications Document Number: 38-07068 Rev. ECN No. Issue Date Orig. of Change Description of Change 107104 06/12/01 IKA Convert from IMI to Cypress