AP2820 BCDSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 18

Technical content

Features

  • Low MOSFET on Resistance: 60mΩ
  • Compliant to USB Specifications
  • Available 2 Versions of Load Ability: Guarantee 2.0A Continuous Load for A/B/C/D Version Guarantee 2.5A Continuous Load for E/F/G/H Version
  • Logic Level Enable Pin: Available with Active-high or Active-low Version
  • Operating Voltage Range: 2.7V to 5.5V
  • Low Supply Current: 75μA (Typ.) (For A/B/C/D versions) 80μA (Typ.) (For E/F/G/H versions)
  • Low Shutdown Current: 1.0μA (Max)
  • Under-voltage Lockout
  • Soft Start-up
  • Over-current Protection
  • Over Temperature Protection
  • Load Short Protection with Fold-back
  • No Reverse Current When Power Off
  • Deglitched FLAG Output with Open Drain
  • With Output Shutdown Pull-low Resistor for A/C/E/G Versions
  • UL Approved (File No. E339337)
  • Nemko CB Scheme IEC60950-1, Ref. Certif No. NO62093

Figure 1. Package Types of AP2820

Figure 2. Pin Configuration of AP2820 (Top View)

1 GND Ground

Figure 3. Functional Block Diagram of AP2820

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited

Ordering Information

Range Condition Part Number Marking ID Packing Type SOIC-8 -40 to 85°C Active High with Auto Discharge (Continuous 2.0A) AP2820AM-G1 2820AM-G1 Tube AP2820AMTR-G1 2820AM-G1 Tape & Reel Active High without Auto Discharge (Continuous 2.0A) AP2820BM-G1 2820BM-G1 Tube AP2820BMTR-G1 2820BM-G1 Tape & Reel -40 to 85°C Active Low with Auto Discharge (Continuous 2.0A) AP2820CM-G1 2820CM-G1 Tube AP2820CMTR-G1 2820CM-G1 Tape & Reel Active Low without Auto Discharge (Continuous 2.0A) AP2820DM-G1 2820DM-G1 Tube AP2820DMTR-G1 2820DM-G1 Tape & Reel -40 to 85°C Active High with Auto Discharge (Continuous 2.5A) AP2820EM-G1 2820EM-G1 Tube AP2820EMTR-G1 2820EM-G1 Tape & Reel Active High without Auto Discharge (Continuous 2.5A) AP2820FM-G1 2820FM-G1 Tube AP2820FMTR-G1 2820FM-G1 Tape & Reel -40 to 85°C Active Low with Auto Discharge (Continuous 2.5A) AP2820GM-G1 2820GM-G1 Tube AP2820GMTR-G1 2820GM-G1 Tape & Reel Active Low without Auto Discharge (Continuous 2.5A) AP2820HM-G1 2820HM-G1 Tube AP2820HMTR-G1 2820HM-G1 Tape & Reel Package M: SOIC-8 MM: MSOP-8 Condition For Continuous 2.0A Versions A: Active High with Auto Discharge B: Active High without Auto Discharge C: Active Low with Auto Discharge D: Active Low without Auto Discharge For Continuous 2.5A Versions E: Active High with Auto Discharge F: Active High without Auto Discharge G: Active Low with Auto Discharge H: Active Low without Auto Discharge G1: Green TR: Tape & Reel Blank: Tube

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited Ordering Information (Continued) Package Temperature Range Condition Part Number Marking ID Packing Type MSOP-8 -40 to 85°C Active High with Auto Discharge (Continuous 2.0A) AP2820AMM-G1 2820AMM-G1 Tube AP2820AMMTR-G1 2820AMM-G1 Tape & Reel Active High without Auto Discharge (Continuous 2.0A) AP2820BMM-G1 2820BMM-G1 Tube AP2820BMMTR-G1 2820BMM-G1 Tape & Reel -40 to 85°C Active Low with Auto Discharge (Continuous 2.0A) AP2820CMM-G1 2820CMM-G1 Tube AP2820CMMTR-G1 2820CMM-G1 Tape & Reel Active Low without Auto Discharge (Continuous 2.0A) AP2820DMM-G1 2820DMM-G1 Tube AP2820DMMTR-G1 2820DMM-G1 Tape & Reel -40 to 85°C Active High with Auto Discharge (Continuous 2.5A) AP2820EMM-G1 2820EMM-G1 Tube AP2820EMMTR-G1 2820EMM-G1 Tape & Reel Active High without Auto Discharge (Continuous 2.5A) AP2820FMM-G1 2820FMM-G1 Tube AP2820FMMTR-G1 2820FMM-G1 Tape & Reel -40 to 85°C Active Low with Auto Discharge (Continuous 2.5A) AP2820GMM-G1 2820GMM-G1 Tube AP2820GMMTR-G1 2820GMM-G1 Tape & Reel Active Low without Auto Discharge (Continuous 2.5A) AP2820HMM-G1 2820HMM-G1 Tube AP2820HMMTR-G1 2820HMM-G1 Tape & Reel BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant and green.

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited Absolute Maximum Ratings (Note 1) Parameter Symbol Value Unit Power Supply Voltage V IN 6.0 V Operating Junction Temperature Range TJ 150 ºC Storage Temperature Range T STG -65 to 150 ºC Lead Temperature (Soldering, 10sec) T LEAD 260 ºC Thermal Resistance Junction to Ambient θJA SOIC-8 135 oC/W MSOP-8 150 CDM (Charge Device Model) 1000 V ESD (Human Body Model) 2000 V Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional op eration of the device at these or any other conditions beyond those indicated under “Recommended Operating Co nditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Min Max Unit Supply Voltage V IN 2.7 5.5 V Operating Ambient Temperature Range TA -40 85 °C

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited

Electrical Characteristics

(VIN=5.0V , CIN=2.2μF, COUT=1.0μF, Typical TA=25°C, Bold typeface applies over -40°C≤TA≤85°C ranges, unless otherwise specified) Parameter Symbol Condition Min Typ Max Unit Input V oltage Range V IN 2.7 5.5 V Switch On Resistance R DS(ON) V IN=5V , IOUT=2.0A 60 80 mΩ Current Limit I LIMIT V OUT=4.0V 2.2 2.7 3.2 A Supply Current I SUPPL Y V IN=5V , No Load 75 105 μA Fold-back Short Current I SHORT V OUT=0 1.18 A Shutdown Supply Current I SHUTDOWN Chip Disable, Shutdown Mode 0.1 1 μA Enable High Input Threshold V ENH 1.6 5.5 V Enable Low Input Threshold V ENL 0 1.0 V Enable Pin Input Current I EN Force 0V to 5V at EN Pin -1.0 1.0 μA Under V oltage Lockou t Threshold V oltage VUVLO V IN Increasing from 0V 2.2 2.5 2.7 V Under V oltage Hysteresis V UVLOHY 0.2 V Reverse Current I REVERSE Chip Disable, V OUT>VIN 0.1 1.0 μA Output Pull Low Resistance after Shutdown RDISCHARGE AP2820A, AP2820C Only 100 200 Ω Output Turn-on Time t ON From Enable Active to 90% o f Output 500 μs FLAG Pin Delay Time t DFLG From Over Current Fault Condition to Flag Active 5 10 15 ms FLAG Pin Low V oltage V FLG I SINK=5mA 35 70 mV FLAG Pin Leakage Current I LEAKAGE FLAG Disable, Force 5.0V 1.0 μA Thermal Shutdown Temperature TOTSD 150 °C Thermal Shutdown Hysteresis T HYOTSD 30 °C

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited Electrical Characteristics (Continued) For E/F/G/H Versions (VIN=5.0V , CIN=2.2μF, COUT=1.0μF, Typical TA=25°C, Bold typeface applies over -40°C≤TA≤85°C ranges, unless otherwise specified) Parameter Symbol Condition Min Typ Max Unit Input V oltage Range V IN 2.7 5.5 V Switch On Resistance R DS(ON) V IN=5V , IOUT=2.5A 60 80 mΩ Current Limit I LIMIT V OUT=4.0V 2.8 3.4 4.2 A Supply Current I SUPPL Y V IN=5V , No Load 80 110 μA Fold-back Short Current I SHORT V OUT=0 1.18 A Shutdown Supply Current I SHUTDOWN Chip Disable, Shutdown Mode 0.1 1 μA Enable High Input Threshold V ENH 1.6 5.5 V Enable Low Input Threshold V ENL 0 1.0 V Enable Pin Input Current I EN Force 0V to 5V at EN Pin -1.0 1.0 μA Under V oltage Lockou t Threshold V oltage VUVLO V IN Increasing from 0V 2.2 2.5 2.7 V Under V oltage Hysteresis V UVLOHY 0.2 V Reverse Current I REVERSE Chip Disable, V OUT>VIN 0.1 1.0 μA Output Pull Low Resistance after Shutdown RDISCHARGE AP2820E, AP2820G Only 100 200 Ω Output Turn-on Time t ON From Enable Active to 90% o f Output 500 μs FLAG Pin Delay Time t DFLG From Over Current Fault Condition to Flag Active 5 10 15 ms FLAG Pin Low V oltage V FLG I SINK=5mA 35 70 mV FLAG Pin Leakage Current I LEAKAGE FLAG Disable, Force 5.0V 1.0 μA Thermal Shutdown Temperature TOTSD 150 oC Thermal Shutdown Hysteresis T HYOTSD 30 oC

Figure 8. Current Limit vs. Ambient Temperature Figure 9. Current Limit vs. Ambient Temperature

Note 2: 2.2μF input capacitor is enough in most application cases. Figure 28. Typical Application of AP2820

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited Mechanical Dimensions S O I C - 8 U n i t : m m ( i n c h ) R0.150(0.006)

High-side Power Distribution Switch with Enable and Flag AP2820 Jul. 2012 Rev 1. 7 BCD Semiconductor Manufacturing Limited Mechanical Dimensions (Continued) M S O P - 8 U n i t : m m ( i n c h ) 4.700(0.185) 5.100(0.201) 0.410(0.016) 0.650(0.026) 0.000(0.000) 0.200(0.008) 3.100(0.122) 2.900(0.114)

BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifi- cations herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others. - Wafer Fab Shanghai SIM-BCD Semiconductor Manufacturing Limited 800, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 BCD Semiconductor Manufacturing Limited MAIN SITE REGIONAL SALES OFFICE Shenzhen Office Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. Shenzhen Office Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office Room E, 5F, Noble Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Tel: +86-755-8826 7951 Fax: +86-755-8826 7865 Taiwan Office BCD Semiconductor (Taiwan) Company Limited 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Taiwan Tel: +886-2-2656 2808 Fax: +886-2-2656 2806 USA Office BCD Semiconductor Corporation 30920 Huntwood Ave. Hayward, CA 94544, U.S.A Tel : +1-510-324-2988 Fax: +1-510-324-2788 - IC Design Group Advanced Analog Circuits (Shanghai) Corporation 8F, Zone B, 900, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com BCD Semiconductor Manufacturing Limited IMPORTANT NOTICE BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifi- cations herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others. - Wafer Fab Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.

800 Yi Shan Road, Shanghai 200233, China

Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 MAIN SITE REGIONAL SALES OFFICE Shenzhen Office Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd., Shenzhen Office Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan District, Shenzhen, China Tel: +86-755-8826 7951 Fax: +86-755-8826 7865 Taiwan Office BCD Semiconductor (Taiwan) Company Limited 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Taiwan Tel: +886-2-2656 2808 Fax: +886-2-2656 2806 USA Office BCD Semiconductor Corp. 30920 Huntwood Ave. Hayward, CA 94544, USA Tel : +1-510-324-2988 Fax: +1-510-324-2788 - Headquarters BCD Semiconductor Manufacturing Limited No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, 200241, China Tel: +86-21-24162266, Fax: +86-21-24162277