DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 12
Technical content
One Channel H-Bridge Power Driver AM1058A
- Features and Benefits Wide supply voltage range up to 11V Maximum continuous current output up to 1.1A Low standby mode current (<1μA) Low quiescent operation current Low MOSFETs On-resistance 0.55Ω@Io=0.6A SOP-8 package for small size PCB layout Provide four operation modes: forward/reverse/stop/brake Over current protection Over temperature protection
- Applications Toys Small Appliances RC servo /Robotics Consumer Products IoT electronic lock
- Description The AM1058A is one channel H -Bridge driver , It provides integrated motor -driver solution for t oys, robotics, consumer products and other low voltage or battery-powered motion control applications. The output driver block consists of N-channel and P-channel power MOSFETs configured as an H -bridge to dri ver DC motor. The AM1058A maximum operational voltage is 11 V. It can supply up to 1.1 A of output continuous current and 2.5A of output peak current. There are internal shutdown function for over-temperature protection and over-current protection (I OCP = 2.5 A). Package material is Pb -Free for the purpose of environmental protection and for sustainable development of the Earth. Ordering Information Orderable Part Number Package Marking AM1058A SOP-8 AM1058A AMtek semiconductors Nov 2017 V 1.2 - 1 -
Absolute Maximum Ratings (TA =25℃) Parameter Symbol Limits Unit Power Supply voltage VCC 12 V Output peak current Iomax 2.5 A Operate temperature range Topr -20～+85 ℃ Storage temperature range Tstg -40～+150 ℃ *Based on 25x25 mm2 FR4 PCB (1 oz.) at single side PCB Recommended operating conditions (TA =25℃) (Set the power supply voltage taking allowable dissipation into considering) Parameter Symbol Min Typ Max Unit Power supply voltage VCC 2.0 11 V IN_A and IN_B VIN_X -0.3 Vcc+0.3 V H-bridge output continuous current IOUT 0 1.1 * A Externally applied PWM frequency FIN_X 0.02 65 KHZ *Based on 25x25mm2 FR4 PCB (1 oz.) at single side PCB The output continuous current can be increased when FR4 PCB (1 oz.) size is increased. AMtek semiconductors Nov 2017 V 1.2 - 2 -
Electrical Characteristics ( Unless otherwise specified, TA = 25℃,VCC=6V) Parameter Symbol Limit Unit Conditions Min Typ Max Power Supplies Quiescent operation current ICC 35 μA Input signal IN_A/B= L/H or H/L or H/H, No load on OUT_A/B Standby mode current ISTB 1 μA Input signal IN_A/B= L/L, No load on OUT_A/B PWM inputs Input H level voltage VIN_xH 2.0 VCC V Input L level voltage VIN_xL 0 0.7 V Input H level current IIN_x 30 μA VCC = 6 V , V IN_x = 3 V Input frequency FIN_x 0.02 65 kHz Input pulldown resistance RIN_x 100 kΩ H-bridge FETs On-resistance Rds(on) 0.53 Ω IO = 200mA Upper and Lower total On-resistance Rds(on) 0.55 Ω IO = 600mA Upper and Lower total TSD Protections Thermal shutdown protection TSDp 150 ℃ Thermal shutdown release TSDr 100 ℃ AMtek semiconductors Nov 2017 V 1.2 - 3 -
Block Diagram VCC GND OUT_A OUT_B Level Shifter Level Shifter High-side / Low-side Driver MG1 MG2 MG4 MG3 IN_A IN_B TSD MG3MG1 MG4MG2 OCP Input Logic Descriptions Function truth table IN_A IN_B OUT_A OUT_B Mode L L Hi-Z Hi-Z Stop L H L H Reverse H L H L Forward H H L L Brake ※Low standby mode current function when IN_A = IN_B = Low level AMtek semiconductors Nov 2017 V 1.2 - 4 -
Pin configuration SOP-8 IN_A IN_B VCC NC OUT_B NC OUT_A GND TOP VIEW Pin Descriptions PIN No Pin Name I/O Description
1 IN_A I Input Half Bridge A
2 NC - No connector
3 IN_B I Input Half Bridge B
4 VCC - Power Supply pin
5 OUT_B O Output Half Bridge B
6 GND - Ground pin
7 OUT_A O Output Half Bridge A
8 NC - No connector
semiconductors Nov 2017 V 1.2 - 5 -
Application IN_A IN_B VCC NC OUT_B NC OUT_A GND IN_A IN_B 0.1μF 10μF~220μF 0.1μF 0.1μF M Circuit Descriptions The function descriptions of capacitors on the application circuit: C1、C2: Power supply VCC pin capacitor: 1) The capacitor can reduce the power spike when the motor is in motion. To avoid the IC directly damaged by the VCC peak voltage. It also can stabilize the power supply voltage and reduce its ripples. 2) The C1 capacitor can compensate power when motor starts running. 3) The capacitor value (μF) determines the stability of the VCC during motor in motion. In general, 10μF capacitor is enough in low voltage power (VCC). If the large voltage power or a heavy loading motor is used, then a larger capacitor would be needed. 4) On the PCB configuration, the C1、C2 must be mounted as close as possible to VCC pin (PIN4). C3: The across-output capacitor ; C4: The across-motor capacitor 1) The capacitors can reduce the power spike of motor when operating. Therefore, a 0.1μF capacitor is recommended. 2) On the PCB configuration, the C3 must be mounted as close as possible to OUT_A&B (PIN 5&PIN 7). 3) The C4 capacitor single-ended can be welded on the motor shell. 4) The C3、C4 capacitor must be added to the general application. AMtek semiconductors Nov 2017 V 1.2 - 6 -
Operating Mode Descriptions H-Bridge basic operating mode： a) Forward mode Definition：When IN_A=H ，IN_B=L，then OUT_A=H ，OUT_B=L b) Reverse mode Definition：When IN_A=L，IN_B=H ，then OUT_B=H ，OUT_A=L c) Brake mode Definition：When IN_A=IN_B= H ，then OUT_A=OUT_B=L d) Stop mode Definition：When IN_A=IN_B= L，then OUT_A=OUT_B= Hi-Z M ON OFF OFF ON M OFF ON ON OFF M OFF OFF ON ON M OFF OFF OFF OFF a) Forward mode b) Reverse mode c) Brake mode d) Stop mode Protection Mechanisms Descriptions 1) Over-temperature protection If the IC junction temperature exceeds 150 ﾟC (Typ.), the internal over-temperature protection function will be triggered, partial FETs in the H-bridge are disabled, that will ensure the safety of customers' products. If the IC junction temperature falls to 100 ﾟ C(Typ.), the IC resumes automatically. 2) Over-current protection (OCP) While the IC conducts a large current, 2.5A (Typ), the internal over -current protection function will be triggered. The device enter protection mode of auto-recover to avoid damaging IC and system. While the IC output short to ground or output A and B short together, the additional internal protection function will be triggered. The device enter protection mode of auto- recover to avoid damaging IC and system. AMtek semiconductors Nov 2017 V 1.2 - 7 -
Thermal Information θja junction-to-ambient thermal resistance 62.5℃/W Ψjt junction-to-top characterization parameter 5.8℃/W Θja is obtained in a simulation on a JEDEC-standard 1s0p board as specified inJESD-51. The Θja number listed above gives an estimate of how much temperature rise is expected if the device was mounted on a standard JEDEC board. When mounted on the actual PCB, the Θja value of JEDEC board is totally different than the Θja value of actual PCB. Ψjt is extracted from the simulation data to obtain Θja using a procedure described in JESD -51, which estimates the junction temperature of a device in an actual PCB. The thermal characterization parameter, Ψjt, is proportional to the temperature difference between the top of the package and the junction temperature. Hence, it is useful value for an engineer verifying device temperature in an actual PCB environment as described in JEDEC JESD-51-12. When Greek letters are not available, Ψjt is written Psi-jt. Definition: Tj Tt PTT dtjjt /)( −=ψDEFINITION : Where : Ψjt (Psi-jt) = Junction-to-T op(of the package) °C/W Tj= Die Junction T emp. °C Tt = Top of package T emp at center. °C Pd = Power dissipation. Watts AMtek semiconductors Nov 2017 V 1.2 - 8 -
Practically, most of the device heat goes into the PCB, there is a very low heat flow through top of the package, So the temperature difference between Tj and Tt shall be small, that is any error caused by PCB variation is small. This constant represents that Ψjt is completely PCB independent and could be used to predict the Tj in the environment of the actual PCB if Tt is measured properly. How to predict Tj in the environment of the actual PCB Step 1 : Used the simulated Ψjt value listed above. Step 2 : Measure Tt value by using Thermocouple Method We recommend use of a small ~40 gauge(3.15mil diameter) thermocouple. The bead and thermocouples wires should touch the top of the package and be covered with a minimal amount of thermally conductive epoxy. The wires should be heat-insulated to prevent cooling of the bead due to heat loss into wires. This is important towards preventing “too cool” Tt measurements, which would lead to the calculated Tj also being too cool. IR Spot Method An IR Spot method should be utilized only when using a tool with a small enough spot area to acquire the true top center “hot spot”. Many so-called “small spot size” tools still have a measurement area of 0~100+mils at “zero” distance of the tool from the surface. This spot area is too big for many smaller packages and likel y would result in cooler readings than the small thermocouple method. Consequently, to match between spot area and package surface size is important while measuring Tt with IR sport method. Step 3 : calculating power dissipation by P ≅(VCC–|Vo_Hi – Vo_Lo|) x Iout + VCC x Icc Step 4 : Estimate Tj value by Tj = Ψjt x P+Tt Step 5: Calculated Θja value of actual PCB by the known Tj Θja(actual) = (Tj-Ta)/P AMtek semiconductors Nov 2017 V 1.2 - 9 -
Maximum Power Dissipation (de-rating curve) under JEDEC PCB & actual PCB AMtek semiconductors Nov 2017 V 1.2 - 10 -
Packaging outline --- SOP-8 Unit : mm SYMBOL MILLIMETERS INCHES Min. Max. Min. Max. A -- 1.75 -- 0.069 A1 0.10 0.225 0.004 0.009 A2 1.30 1.50 0.051 0.059 A3 0.60 0.70 0.024 0.028 b 0.39 0.48 0.015 0.019 c 0.21 0.26 0.008 0.010 D 4.70 5.10 0.185 0.201 E 5.80 6.20 0.228 0.244 E1 3.70 4.10 0.146 0.161 e 1.27 TYP . 0.05 TYP . h 0.25 0.50 0.010 0.020 L 0.50 0.80 0.020 0.031 L1 1.05 TYP 0.041 TYP . AMtek semiconductors Nov 2017 V 1.2 - 11 -
Marking Identification NOTE: Row1 ： Logo Row2 ： Device Row3 ： Wafer Lot No、Assembly Year、Assembly Date Code Example : Wafer Lot No is 88888 + last number of assembly year is 5 (F=5) + produce at the week 12 Then mark 〝88888F12〞 Assembly Year Code： ( Year_A=0,B=1,C=2,D=3,E=4,F=5,G=6,H=7,I=8,J=9, e.g. : 2015 =F ) Row4 ： Product designate code, we type A to discriminate. AMtek semiconductors Nov 2017 V 1.2 - 12 -