DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
Ver.1.02 ADI12-8(FIT)GY 2 Installation Environment Requirements Parameter Requirement description Operating temperature 0 - 50C Storage temperature -10 - 60C Humidity 10 - 90% RH (No condensation) Floating dust particles Not to be excessive Corrosive gases None Line- Noise resistance Line-noise AC line/2kV, Signal line/1kV (IEC1000-4-4Level 3, EN61000-4-4Level 3) Static electricity resistance Contact discharge/4kV (IEC1000-4-2Level 2, EN61000-4-2Level 2) Atmospheric discharge/8kV (IEC1000-4-2Level 3, EN61000-4-2Level 3) Vibration resistance Sweep resistance 10 - 57Hz/semi-amplitude 0.15mm, 57 - 150Hz/2.0G 80minutes each in X, Y, and Z directions (JIS C0040 -compliant, IEC68-2-6-compliant) Impact resistance 15G, half-sine shock for 11ms in X, Y, and Z directions (JIS C004-compliant, IEC68-2-27-compliant) Certification RoHS,CE EMC,FCC,VCCI Module …1 First Step Guide …1 CD-ROM [F&eIT Series Setup Disk] *1…1 Interface connector plugs …2 Warranty Certificate…1 Serial number label…1 *1 The CD-ROM contains various software and User’s Manual. When connecting the Module to an external device, you can use the supplied connector plug. When wirin g the Module, strip off approximately 7 - 8 mm of the covering for the cable, and insert the bare wire by pressing the orange button on the connector plug. Releasing the orange button after the wire is inserted to fix the cable. Compatible wires are AWG 28 - 20. Removing the connector plug by grasping the cable can break the wire. The Module can be connected to an external device using a 12- pin (1 group) connector that is provided on the Module face. (1.2) 94.0 25.2 64.7 4.03.5 (1.2) [mm] ADI12- Device ID CH0 CH1 CH2 CH3 AG AG AG AG CH4 CH5 CH6 CH7 AG AG AG AG RUN STATUS 14.035.045.0 14.0 31.5 Press this section to insert the wire material. 7 - 8mm ADI12-8 Device ID CH0 CH1 CH2 CH3 AG AG AG AG CH4 CH5 CH6 CH7 AG AG AG AG - Connector used: 2.5-mm pitch, 12-pin type, 4.0A nominal current MC0.5/12-G-2.5 connector (made by Phoenix Contact Corp.) - Applicable plug: Front-operable spring gauge type FK-MC 0,5/12-ST-2,5 plug (made by Phoenix Contact Corp.) Applicable wire: AWG 28 - 20 RUN STATUS CAUTION CH0 [+] CH0 [-] AG CH1 [+] CH1 [-] AG CH2 [+] CH2 [-] AG CH3 [+] CH3 [-] AG Analog Input 0ch [+] Analog Input 0ch [-] Analog Ground Analog Input 1ch [+] Analog Input 1ch [-] Analog Ground Analog Input 2ch [+] Analog Input 2ch [-] Analog Ground Analog Input 3ch [+] Analog Input 3ch [-] Analog Ground CH0 CH1 CH2 CH3 CH4 [+] CH4 [-] AG CH5 [+] CH5 [-] AG CH6 [+] CH6 [-] AG CH7 [+] CH7 [-] AG Analog Input 4ch [+] Analog Input 4ch [-] Analog Ground Analog Input 5ch [+] Analog Input 5ch [-] Analog Ground Analog Input 6ch [+] Analog Input 6ch [-] Analog Ground Analog Input 7ch [+] Analog Input 7ch [-] Analog Ground CH4 CH5 CH6 CH7 Packing List Physical Dimensions How to Connect an Interface Connector Signal Layout on the Interface Connector
Ver.1.02 ADI12-8(FIT)GY 3 The controller module distinguishes and keeps track of the modules that are connected t o it by assigning device IDs to them. Each module, therefore, should be assigned a unique ID. A Device ID can be assigned in a 0 - 7 range, so that a maximum of eight modules can be distinguished. To connect this product to the ADI12 -8(USB)GY , assign a device ID between 1 and 3. The factory setting for the Device ID is [0]. Setup Method A device ID can be set by turning the rotary switch on the device face. To set a device ID, turn the switch knob. Device ID Factory settings: (Device ID = 0) Stack Connector Control Circuit Device ID Interface Connector CH0 - CH3 Interface Connector CH4 - CH7 Isolator 8-channel Multiplexer with Voltage Protection Instrument Amplifier A/D Converter DC/DC Converter Setting a Device ID Block Diagram