ACPM-7822 AVAGO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Features

  • Thin Package (0.9mm typ)
  • Excellent Linearity
  • 3-mode power control with Vbp and Vmode Bypass / Mid Power Mode / High Power Mode
  • High Efficiency at max output power
  • 10-pin surface mounting package
  • Internal 50ohm matching networks for both RF input and output
  • Lead-free, RoHS compliant, Green

Applications

  • Digital Japan CDMA Band (3GPP2 Band Class 3)

Ordering Information

ACPM-7822-TR1 1000 178mm (7”) Tape/Reel ACPM-7822-BLK 100 Bulk Component Image

No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value. Operation of any single parameter outside these conditions with the remaining parameters set at or below nominal values may result in permanent damage. Description Min. Typ. Max. Unit RF Input Power (Pin) 0 10.0 dBm DC Supply Voltage (Vcc1, Vcc2) 0 3.4 5.0 V Enable Voltage (Ven) 0 2.6 3.3 V Mode Control Voltage (Vmode) 0 2.6 3.3 V Bypass Control (Vbp) 0 2.6 3.3 V Storage Temperature (Tstg) -55 25 +125 °C Recommended Operating Condition Description Min. Typ. Max. Unit DC Supply Voltage (Vcc1, Vcc2) 3.2 3.4 4.2 V Enable Voltage (Ven) Low High 1.35 2.6 0.5 2.9 V V Mode Control Voltage (Vmode) Low High 1.35 2.6 0.5 2.9 V V Bypass Control Voltage (Vbp) Low High 1.35 2.6 0.5 2.9 V V Operating Frequency (fo) 898 925 MHz Ambient Temperature (Ta) -30 25 85 °C Operating Logic Table Power Mode Ven Vbp Vmode Pout High Power Mode High High Low ~ 28 dBm Mid Power Mode High High High ~ 18 dBm Bypass Mode High Low X ~ 11 dBm Shut Down Mode Low Low Low –

Electrical Characteristics

Conditions: Vcc=3.4V, Ven=2.6V, T=25°C, Zin/Zout=50ohm, IS-95 RL, unless otherwise specified. Characteristics Condition Min. Typ. Max. Unit Operating Frequency Range 898 – 925 MHz Gain High Power Mode, Pout=28dBm 23 28 dB Mid Power Mode, Pout=18dBm 13 19 dB Bypass Mode, Pout=11dBm 8 11.5 dB Power Added Efficiency High Power Mode, Pout=28dBm 35.3 37.7 % Mid Power Mode, Pout=18dBm 15.3 22.3 % Bypass Mode, Pout=11dBm 8.0 11.9 % Total Supply Current High Power Mode, Pout=28dBm 492 525 mA Mid Power Mode, Pout=18dBm 82 120 mA Bypass Mode, Pout=11dBm 29 43 mA Quiescent Current High Power Mode 93 120 mA Mid Power Mode 23 30 mA Bypass Mode 3 5 mA Enable Current 100 µA Mode Control Current 100 µA Bypass Control Current 100 µA Total Current in Power-down mode Ven=0V, Vmode=0V, Vbp=0V 0.2 5 µA Adjacent Channel Power Ratio 900 kHz offset

1.98 MHz offset

High Power Mode, Pout=28dBm -50 -57 -45 -53 dBc dBc 900 kHz offset Mid Power Mode, Pout=18dBm -51 -64 -46 -54 dBc dBc 900 kHz offset Bypass Mode, Pout=11dBm -59 -69 -46 -54 dBc dBc Harmonic Suppression Second Third High Power Mode, Pout=28dBm -30 -40 dBc dBc Input VSWR High Power Mode 2:1 2.5:1 Stability (Spurious Output) In-Band Load VSWR <= 5:1, All Phase Forwarded Power Fixed, All Power Modes, with Input Filter -60 dBc Noise Power in Rx Band (843-870 MHz) High Power Mode, Pout=28dBm -135 -132 dBm/Hz Noise Power in GPS Band (1575.42 MHz) High Power Mode, Pout=28dBm -145 -141 dBm/Hz Ruggedness No Damage Pout<28dBm & Pin<10dBm, All phase High Power Mode 10:1 VSWR

(Vcc=3.4V, Ven=2.6, Vbp, Vmode= 0V or 2.6V, T=25°C, Zin/Zout=50ohm, IS-95 RL) Total Current vs. Output Power Gain vs. Output Power Adjacent Channel Power Ratio 1 vs. Output Power Adjacent Channel Power Ratio 2 vs. Output Power Power Added Efficiency vs. Output Power 0 5 10 15 20 25 30 Pout (dBm) 100 200 300 400 500 0 5 10 15 20 25 30 Pout (dBm) Current (mA) 898MHz 915MHz 925MHz 30Gain (dB) -70 -65 -60 -55 -50 -45 -40 -35 0 5 10 15 20 25 30 Pout (dBm) ACPR1 (dBc) -80 -75 -70 -65 -60 -55 -50 0 5 10 15 20 25 30 Pout (dBm) ACPR2 (dBc) 0 5 10 15 20 25 30 Pout (dBm) PAE (%) 898MHz 915MHz 925MHz 898MHz 915MHz 925MHz 898MHz 915MHz 925MHz 898MHz 915MHz 925MHz

All dimensions are in millimeter X-RAY TOP VIEW 1.90 1.70 0.85 1.20 1.90 0.40 0.40 PIN Description Pin # Name Description

1 Ven PA Enable

2 Vmode Mode Control

3 Vbp Bypass Control

4 RFin RF Input

5 Vcc1 DC Supply Voltage

6 Vcc2 DC Supply Voltage

7 GND Ground

8 RFout RF Output

9 GND Ground

10 GND Ground

All dimensions are in millimeter 4 ± 0.1 4 ± 0.1 Pin 1 Mark 0.6 0.9 ± 0.1 Marking Specification Pin 1 Mark AVAGO ACPM-7822 PYYWW AAAAA Manufacturing Part Number Lot Number P Manufacturing info YY Manufacturing Year WW Work Week AAAAA Assembly Lot Number

Solder Paste Stencil Aperture 0.25 0.85 0.4 0.6 0.5 0.1 Ø 0.3mm on 0.6mm pitch 0.7 0.5 0.55 0.85 2.4 1.8 0.6 0.5 1.6 2.0 0.85 0.4 PCB Design Guidelines The recommended PCB land pattern is shown in figures on the left side. The substrate is coated with solder mask between the I/O and conductive paddle to protect the gold pads from short circuit that is caused by solder bleeding/bridging. Stencil Design Guidelines A properly designed solder screen or stencil is required to ensure optimum amount of solder paste is deposited onto the PCB pads. The recommended stencil layout is shown here. Reducing the stencil opening can potentially generate more voids. On the other hand, stencil openings larger than 100% will lead to excessive solder paste smear or bridging across the I/O pads or conductive paddle to adjacent I/O pads. Considering the fact that solder paste thickness will directly affect the quality of the solder joint, a good choice is to use laser cut stencil composed of 0.100mm(4mils) or 0.127mm(5mils) thick stainless steel which is capable of producing the required fine stencil outline.

Evaluation Board Schematic

1 Ven

2 Vmode

3 Vbp

4 RFin

5 Vcc1 Vcc2 6

2.2uF Ven 100pF 2.2uF 680pF Evaluation Board Description

A0 4.40±0.10 B0 4.40±0.10 K0 1.70±0.10 D0 1.55±0.05 D1 1.60±0.10 P0 4.00±0.10 P1 8.00±0.10 Dimension Millimeter P2 2.00±0.05 P10 40.00±0.20 E 1.75±0.10 F 5.50±0.05 W 12.00±0.30 T 0.30±0.05

Plastic Reel Format (all dimensions are in millimeters) Reel Drawing NOTES: 1. Reel shall be labeled with the following information (as a minimum). a. manufacturers name or symbol b. Avago Technologies part number c. purchase order number d. date code e. quantity of units 2. A certificate of compliance (c of c) shall be issued and accompany each shipment of product. 3. Reel must not be made with or contain ozone depleting materials. 4. All dimensions in millimeters (mm) 50 min. 12.4 +2.0 -0.0 18.4 max. min wide (ref) Slot for carrier tape insertion for attachment to reel hub (2 places 180° apart) BACK VIEW FRONT VIEW 178 Shading indicates thru slots +0.4 -0.2 21.0 ± 0.8 13.0 ± 0.2 1.5 min.

ESD (Electrostatic Discharge) Electrostatic discharge occurs naturally in the environ- naturally in the environ-naturally in the environ - ment. With the increase in voltage potential, the outlet of neutralization or discharge will be sought. If the acquired discharge route is through a semiconductor device, de- through a semiconductor device, de-through a semiconductor device, de- de-de- structive damage will result. ESD countermeasure methods should be developed and used to control potential ESD damage during handling in a factory environment at each manufacturing site. MSL (Moisture Sensitivity Level) Plastic encapsulated surface mount package is sensitive to damage induced by absorbed moisture and temperature. Avago Technologies follows JEDEC Standard J-STD 020B. Each component and package type is classified for moisture sensitivity by soaking a known dry package at various temperatures and relative humidity, and times. Moisture Classification Level and Floor Life MSL Level Floor Life (out of bag) at factory ambient =< 30°C/60% RH or as stated

1 Unlimited at =< 30°C/85% RH

6 Mandatory bake before use. After bake, must be reflowed within the time limit specified on the label Note : 1. The MSL Level is marked on the MSL Label on each shipping bag. After soak, the components are subjected to three con - secutive simulated reflows. The out of bag exposure time maximum limits are deter - mined by the classification test describe below which cor- responds to a MSL classification level 6 to 1 according to the JEDEC standard IPC/JEDEC J-STD-020B and J-STD-033. ACPM-7822 is MSL3. Thus, according to the J-STD-033 p.11 the maximum Manufacturers Exposure Time (MET) for this part is 168 hours. After this time period, the part would need to be removed from the reel, de-taped and then re-baked. MSL classification reflow temperature for the ACPM-7822 is targeted at 260°C +0/-5°C. Figure and table on next page show typical SMT profile for maximum temperature of 260 +0/-5°C.

Reflow Profile Recommendations Typical SMT Reflow Profile for Maximum Temperature = 260 +0/-5°C Time Temperature Tp TL tp tL t 25°C to Peak Ramp-up ts Tsmin Ramp-down Preheat Critical Zone TL to Tp Tsmax Typical SMT Reflow Profile for Maximum Temperature = 260 +0/ -5°C Profile Feature Sn-Pb Solder Pb-Free Solder Average ramp-up rate (TL to TP) 3°C/sec max 3°C/sec max Preheat – Temperature Min (Tsmin) – Temperature Max (Tsmax) – Time (min to max) (ts) 100°C 150°C 60-120 sec 150°C 200°C 60-180 sec Tsmax to TL – Ramp-up Rate 3°C/sec max Time maintained above: – Temperature (TL) – Time (TL) 183°C 60-150 sec 217°C 60-150 sec Peak temperature (Tp) 240 +0/-5°C 260 +0/-5°C Time within 5°C of actual Peak Temperature (tp) 10-30 sec 20-40 sec Ramp-down Rate 6°C/sec max 6°C/sec max Time 25°C to Peak Temperature 6 min max. 8 min max.

Packages described in this document must be stored in sealed moisture barrier, antistatic bags. Shelf life in a sealed moisture barrier bag is 12 months at <40°C and 90% relative humidity (RH) J-STD-033 p.7. Out-of-Bag Time Duration After unpacking the device must be soldered to the PCB within 168 hours as listed in the J-STD-020B p.11 with factory conditions <30°C and 60% RH. Baking It is not necessary to re-bake the part if both conditions (storage conditions and out-of bag conditions) have been satisfied. Baking must be done if at least one of the con - ditions above have not been satisfied. The baking condi - tions are 125°C for 12 hours J-STD-033 p.8. CAUTION Tape and reel materials typically cannot be baked at the temperature described above. If out-of-bag exposure time is exceeded, parts must be baked for a longer time at low temperatures, or the parts must be de-reeled, de-taped, re-baked and then put back on tape and reel. (See moisture sensitive warning label on each shipping bag for information of baking). Board Rework Component Removal, Rework and Remount If a component is to be removed from the board, it is recommended that localized heating be used and the maximum body temperatures of any surface mount component on the board not exceed 200°C. This method will minimize moisture related component damage. If any component temperature exceeds 200°C, the board must be baked dry per 4-2 prior to rework and/or component removal. Component temperatures shall be measured at the top center of the package body. Any SMD packages that have not exceeded their floor life can be exposed to a maximum body temperature as high as their specified maximum reflow temperature. Removal for Failure Analysis Not following the above requirements may cause moisture/ reflow damage that could hinder or completely prevent the determination of the original failure mechanism. Baking of Populated Boards Some SMD packages and board materials are not able to withstand long duration bakes at 125°C. Examples of this are some FR-4 materials, which cannot withstand a 24 hr bake at 125°C. Batteries and electrolytic capacitors are also temperature sensitive. With component and board temperature restrictions in mind, choose a bake tem - perature from Table 4-1 in J-STD 033; then determine the appropriate bake duration based on the component to be removed. For additional considerations see IPC-7711 andIPC-7721. Derating due to Factory Environmental Conditions Factory floor life exposures for SMD packages removed from the dry bags will be a function of the ambient envi - ronmental conditions. A safe, yet conservative, handling approach is to expose the SMD packages only up to the maximum time limits for each moisture sensitivity level as shown in next table. This approach, however, does not work if the factory humidity or temperature is greater than the testing conditions of 30°C/60% RH. A solution for addressing this problem is to derate the exposure times based on the knowledge of moisture diffusion in the component package materials ref. JESD22-A120). Recommended equivalent total floor life exposures can be estimated for a range of humidities and temperatures based on the nominal plastic thickness for each device. Table on next page lists equivalent derated floor lives for humidities ranging from 20-90% RH for three tempera - ture, 20°C, 25°C, and 30°C. Table on next page is applicable to SMDs molded with novolac, biphenyl or multifunctional epoxy mold compounds. The following assumptions were used in cal- culating this table: 1. Activation Energy for diffusion = 0.35eV (smallest known value). 2. For ≤60% RH, use Diffusivity = 0.121exp ( -0.35eV/kT) mm2/s (this used smallest known Diffusivity @ 30°C). 3. For >60% RH, use Diffusivity = 1.320exp ( -0.35eV/kT) mm2/s (this used largest known Diffusivity @ 30°C).

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. AV02-1777EN - February 17, 2009 Recommended Equivalent Total Floor Life (days) @ 20°C, 25°C & 30°C For ICs with Novolac, Biphenyl and Multifunctional Epoxies (Reflow at same temperature at which the component was classified) Maximum Percent Relative Humidity Package Type and Body Thickness Moisture Sensitiv- ity Level 5% 10% 20% 30% 40% 50% 60% 70% 80% 90% Body Thickness ≥3.1 mm Including PQFPs >84 pin, PLCCs (square) All MQFPs or All BGAs ≥1 mm Level 2a ∞ 103 30°C 25°C 20°C Level 3 ∞ 30°C 25°C 20°C Level 4 ∞ 30°C 25°C 20°C Level 5 ∞ 30°C 25°C 20°C Level 5a ∞ 30°C 25°C 20°C Body 2.1 mm ≤ Thickness <3.1 mm including PLCCs (rectangular) 18-32 pin SOICs (wide body) SOICs ≥20 pins, PQFPs ≤80 pins Level 2a ∞ 148 30°C 25°C 20°C Level 3 ∞ 30°C 25°C 20°C Level 4 ∞ 30°C 25°C 20°C Level 5 ∞ 30°C 25°C 20°C Level 5a ∞ 0.5 0.5 30°C 25°C 20°C Body Thickness <2.1 mm including SOICs <18 pin All TQFPs, TSOPs or All BGAs <1 mm body thickness Level 2a ∞ 30°C 25°C 20°C Level 3 ∞ 30°C 25°C 20°C Level 4 ∞ 30°C 25°C 20°C Level 5 ∞ 30°C 25°C 20°C Level 5a ∞ 0.5 30°C 25°C 20°C