A625308 AMICC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Preliminary 32K X 8 BIT CMOS SRAM PRELIMINARY ( December , 2000, Version 0. 2 ) AMIC Technology, Inc. Document Title 32K X 8 BIT CMOS SRAM

Revision History

Rev. No. History Issue Date Remark

0.0 Initial issue June 30, 1998 Preliminary

0.1 Erase 28 - pin DIP package type May 21, 1999

0.2 Erase 55ns part December 1, 2000

Preliminary 32K X 8 BIT CMOS SRAM PRELIMINARY ( December , 2000, Version 0. 2 ) 1 AMIC Technology, Inc.

Features

n External Operating Voltage: 4.5 V to 5.5V n Access times: 70 ns (max.) n Current: A625308 - L series: Operating: 70mA (max.) Standby: 100 µA (max.) A625308 - S series: Operating: 70mA (max.) Standby: 25 µA (max.) n Full static operation, no clock or refreshing required n All inputs and o utputs are directly TTL compatible n Common I/O using three - state output n Data retention voltage: 2.0V (min.) n Available in 28 - pin SOP and TSOP (forward and reverse type) packages General Description The A625308 is a low operating current 262,144 - bit static random access memory organized as 32,768 words by 8 bits and operates on a single 5V power supply. Inputs and three - state outputs are TTL compatible and allow for direct interfacing with common system bus structures. Minimum standby power is drawn by this device when CE is at a high level, independent of the other input levels. Data retention is guaranteed at a power supply voltage as low as 2.0V. Pin Configurations n SOP n TSOP A14 A12 I/O 0 I/O 1 I/O 2 GND I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CE OE A11 A13 WE VCC A10 A625308M 14 15 A625308V A11 2 A13 A14 A12 I/O 6 I/O 5 I/O 4 I/O 3 VSS I/O 2 I/O 1 I/O 0 A10 VCC I/O 7 OE WE CE A625308R A4 2 VCC A13 A11 I/O 0 I/O 1 I/O 2 VSS I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 A10 A14 A12 WE OE CE

PRELIMINARY ( December , 2000, Version 0. 2 ) 2 AMIC Technology, Inc. Block Diagram ROW DECODER

512 X 512

Pin No. Symbol Description 1 - 10, 21, 23 - 26 A0 - A14 Address Input 11 - 13, 15 - 19 I/O 0 - I/O 7 Data Inputs/Outputs

14 GND Ground

20 CE Chip Enable

22 OE Outpu t Enable

27 WE Write Enable

28 VCC Power Supply

Pin No. Symbol Description

1 OE Output Enable

2 - 5, 8 - 17, 28 A0 - A14 Address Input

7 VCC Power Supply

6 WE Write Enab le

18 - 20, 22 - 26 I/O 0 - I/O 7 Data Inputs/Outputs

21 GND Ground

27 CE Chip Enable

PRELIMINARY ( December , 2000, Version 0. 2 ) 3 AMIC Technology, Inc. Recommended DC Operating Conditions (T A = 0 °C to + 70 °C) Symbol Parameter Min. Typ. Max. Unit VCC Supply Voltage 4.5 5.0 5.5 V GND Ground 0 0 0 V V IH Input High Voltage 2.2 3.5 VCC + 0.3 V V IL Input Low Voltage - 0.3 0 +0.8 V Absolute Maximum Ratings* *Comments Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections o f this specification is not implied and exposure to absolute maximum rating conditions for extended periods may affect device reliability. Symbol Parameter A625308-70L A625308-70S Unit Conditions Min. Max. Min. Max. ILI Input Leakage Current - 1 - 1 µA V IN = GND to VCC ILO Output Leakage Current - 1 - 1 µA CE = V IH or OE = V IH or WE = V IH V I/O = GND to VCC ICC Active Power Supply Current - 15 - 15 mA CE = V IL, I I/O = 0mA ICC1 Dynamic Operating Current - 70 - 70 mA Min. Cycle, Duty = 100% CE = V IL, I I/O = 0mA ICC2 Dynamic Operating Current - 15 - 15 mA CE = V IL, V IH = VCC V IL = 0V, f = 1 MHz I I/O = 0 mA

PRELIMINARY ( December , 2000, Version 0. 2 ) 4 AMIC Technology, Inc. Symbol Parameter A625308-70L A625308-70S Unit Conditions Min. Max. Min. Max. ISB Supply Current - 3 - 2 mA CE = V IH ISB1 Standby Power - 100 - 25 µA CE ≥ VCC - 0.2V V IN ≥ 0V V OL Output Low Voltage - 0.4 - 0.4 V I OL = 2.1mA V OH Output High Voltage 2.4 - 2.4 - V I OH = - 1.0mA Truth Table Mode CE OE WE I/O Operation Supply Current Standby H X X High Z ISB, I SB1 Output Disable L H H High Z ICC, I CC1, I CC2 Read L L H D OUT ICC, I CC1, I CC2 Write L X L D IN ICC, I CC1, I CC2 Note: X: H or L Capacitance (T A = 25 °C, f = 1.0 MHz) Symbol Parameter Min. Max. Unit Conditions C IN* Input Capacitance 6 pF V IN = 0V C I/O* Input/Output Capacitance 8 pF V I/O = 0V * These parameters are sampled and not 100% tested.

PRELIMINARY ( December , 2000, Version 0. 2 ) 5 AMIC Technology, Inc. AC Characteristics (T A = 0 °C to +70 °C, VCC = 5.0V ± 10%) Symbol Parameter A625308-70L/70S Unit Min. Max. Read Cycle tRC Read Cycle Time 70 - ns tAA Address Access Time - 70 ns tACE Chip Enable Access Time - 70 ns tOE Output Enable to Output Valid - 35 ns tCLZ Chip Enable to Output in Low Z 10 - ns tOLZ Output Enable to Output in Low Z 5 - ns tCHZ Chip Disable to Output in High Z - 25 ns tOHZ Output Disable to Output in High Z - 25 ns tOH Output Hold from Address Change 5 - ns Write Cycle tWC Write Cycle Time 70 - ns tCW Chip Enable to End of Write 60 - ns tAS Address Set up Time 0 - ns tAW Address Valid to End of Write 60 - ns tWP Write Pulse Width 50 - ns tWR Write Recovery Time 0 - ns tWHZ Write to Output in High Z - 30 ns tDW Data to Write Time Overlap 30 - ns tDH Data Hold from Write Time 0 - ns tOW Output Active from End of Write 5 - ns Notes: tCHZ, t OHZ and t WHZ are defined as the time at which the outputs achieve the open circuit condition and are not referred to output voltage levels.

PRELIMINARY ( December , 2000, Version 0. 2 ) 6 AMIC Technology, Inc. Timing Waveforms Read Cycle 1 (1) tRC tAA tOH Address D OUT tOHZ5 tCHZ5 tACE tCLZ5 tOLZ5 tOE CE OE Read Cycle 2 (1, 2, 4) tRC tOH tAA tOH Address D OUT

PRELIMINARY ( December , 2000, Version 0. 2 ) 7 AMIC Technology, Inc. Timing Waveforms (continued) Read Cycle 3 (1, 3, 4) tCLZ 5 tACE tCHZ 5 CE D OUT Notes: 1. WE is high for Read Cycle. 2. Device is continuously enabled, CE = V IL. 3. Address valid prior to or coincident with CE transition low. 4. OE = V IL. 5. Transition is measured ±500mV from steady state. This parameter is sampled and not 100% tested. Write Cycle 1 (6) (Write Enable Controlled) tWC Address CE D IN tOW 7 tDHtDW tWHZ 7 tWP2tAS1 (4) tCW5 tAW tWR3 WE D OUT

PRELIMINARY ( December , 2000, Version 0. 2 ) 8 AMIC Technology, Inc. Timing Waveforms (continued) Write Cycle 2 (6) (Chip Enable Controlled) tWC Address CE D IN tDHtDW (4) tCW5 tAW tWR3 WE D OUT tWHZ7 tWP2 tAS1 Notes: 1. t AS is measured from the address valid to the beginning of Write. 2. A Write occu rs during the overlap (t WP) of a low CE and a low WE . 3. t WR is measured from the earliest of CE or WE going high to the end of the Write cycle. 4. If the CE low transition occurs simultaneously with the WE low transition or after the WE transition, outputs remain in a high impedance state. 5. t CW is measured from the later of CE goi ng low to the end of Write. 6. OE level is high or low. 7. Transition is measured ±500mV from steady. This parameter is sampled and not 100% tested.

PRELIMINARY ( December , 2000, Version 0. 2 ) 9 AMIC Technology, Inc. Figure 1. Output Load Figure 2. Output Load for tCLZ

PRELIMINARY ( December , 2000, Version 0. 2 ) 10 AMIC Technology, Inc.

Ordering Information

Part No. Access Time (ns) Operating Current Max. (mA) Standby Current Max. (µA ) Package A625308M - 70L 70 100 28L SOP A625 308M - 70S 70 25 28L SOP A625308V - 70L 70 100 28L TSOP (Forward) A625308V - 70S 70 25 28L TSOP (Forward) A625308R - 70L 70 100 28L TSOP (Reverse) A625308R - 70S 70 25 28L TSOP (Reverse)

PRELIMINARY ( December , 2000, Version 0. 2 ) 11 AMIC Technology, Inc.

Package Information

SOP (W.B.) 28L Outline Dimensions unit: inches /mm E H L L 1 c See Detail F Detail FB 1528 A 1 A 2 A S D Seating Plane D y ey θ Dimensions in inches Dimensions in mm Symbol Min Nom Max Min Nom Max D - 0.713 0.728 - 18.11 18.49 θ 0° - 8° 0° - 8° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. 3. Dimension S includes end flash.

PRELIMINARY ( December , 2000, Version 0. 2 ) 12 AMIC Technology, Inc. D 1 E e D L A A 2 c Detail "A" D y Detail "A" S A 1 b θ TSOP 28L TYPE I (8 X 13.4mm) Outline Dimensions unit: inches/mm Dimensions in inches Dimensions in mm Symbol Min Nom Max Min Nom Max c 0.005 - 0.008 0.12 - 0.21 e 0.022 BSC 0.55 BSC S 0.017 TYP 0.425 TYP Notes: 1. The maximum value of dimension D 1 includes end flash. 2. Dimension E does not include resin fins. 3. Dimension S includes end flash.