ZJ080NA-08A CHIMEI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 24
Technical content
Datasheet sections
- 8.1 Packaging Material Table
- 8.2 Packaging Quantity
- 8.3 Packaging Drawing
Customer: Model Name: ZJ080NA-08A Date: 2012/05/17 Version: 01 ■■ ■■ Preliminary Specification □□ □□ Final Specification For Customer’s Acceptance Approved by Comment Approved by Reviewed by Prepared by Stanley Leung 2012/05/21 Wenyi Wang 2012/05/18 Sunny Sun 2012/5/17
Pre-Spec. 01 2012/05/17 Initial Release.
- General Specifications No. Item Specification Remark 1 LCD size 8.0 inch(Diagonal)
2 Driver element a-Si TFT active matrix
3 Resolution 1024 x 3(RGB) x 600
4 Display mode Normally White
5 Dot pitch 0.1725(W) x 0.1656(H) 6 Active area 176.64(W) x 99.36(H)mm 7 Module size 192.8(W) x 116.9(H) x 6.4(D)mm Note 1
8 Surface treatment Plain
9 Color arrangement RGB-stripe
10 View Direction(Gray Inversion) 6:00 O’ Clock
11 Interface Digital
12 Backlight power consumption 3.56W (Typ.)
13 Panel power consumption TBD W(Typ)
14 Weight TBD (Typ)
Note 1: Refer to Mechanical Drawing.
- Pin Assignment 2.1. TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface. The recommended model is FH12A-40S-0.5SH manufactured by Hirose. Pin No. Symbol I/O Function Remark
1 VCOM P Common Voltage
2 VDD P Power Voltage for digital circuit
3 VDD P Power Voltage for digital circuit
4 NC --- No connection
5 Reset I Global reset pin
6 STBYB I
Standby mode, Normally pulled high STBYB = “1”, normal operation STBYB = “0”, timing controller, source driver will turn off, all output are High-Z
7 GND P Ground
8 RXIN0- I - LVDS differential data input
9 RXIN0+ I + LVDS differential data input
10 GND P Ground
11 RXIN1- I - LVDS differential data input
12 RXIN1+ I + LVDS differential data input
13 GND P Ground
14 RXIN2- I - LVDS differential data input
15 RXIN2+ I + LVDS differential data input
16 GND P Ground
17 RXCLKIN- I - LVDS differential clock input
18 RXCLKIN+ I + LVDS differential clock input
19 GND P Ground
20 RXIN3- I - LVDS differential data input
21 RXIN3+ I + LVDS differential data input
22 GND P Ground
23 NC --- No connection
24 NC --- No connection
25 GND P Ground
26 NC --- No connection
27 DIMO O Backlight CABC controller signal output
28 SELB I 6bit/8bit mode select Note1
29 AVDD P Power for Analog Circuit
30 GND P Ground
31 LED- P LED Cathode
32 LED- P LED Cathode
33 L/R I Horizontal inversion Note3
34 U/D I Vertical inversion Note3
35 VGL P Gate OFF Voltage
36 CABCEN1 I CABC H/W enable Note2
37 CABCEN0 I CABC H/W enable Note2
38 VGH P Gate ON Voltage
39 LED+ P LED Anode
40 LED+ P LED Anode
I: input, O: output, P: Power Note1: If LVDS input data is 6 bits ,SELB must be set to High; If LVDS input data is 8 bits ,SELB must be set to Low. Note2: When CABC_EN=”00”, CABC OFF. When CABC_EN=”01”, user interface image. When CABC_EN=”10”, still picture. When CABC_EN=”11”, moving image. When CABC off, don’t connect DIMO, else connect it to backlight. Note3: When L/R=”0”, set right to left scan direction. When L/R=”1”, set left to right scan direction. When U/D=”0”, set top to bottom scan direction. When U/D=”1”, set bottom to top scan direction.
Note: Definition of scanning direction. Refer to the figure as below: Up Left Right Down
- Operation Specifications 3.1. Absolute Maximum Rating ( GND=AVSS=0V, Note 1) Values Item Symbol Min. Max. Unit Remark VDD -0.3 5.0 V AVDD 6.5 13.5 V VGH -0.3 42 V VGL -20.0 0.3 V Power voltage VGH-VGL - 40.0 V TOP -20 80 ℃ Operation Temperature Storage Temperature TST -30 80 ℃ LED Reverse Voltage VR - 5 V each LED LED Forward Current I F - 60 mA each LED Note 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. Note 2: VR Conditions: Zener Diode 60mA
3.1.1. Typical Operation Conditions (GND=AVSS=0V, Note 1) Values Item Symbol Min. Typ. Max. Unit Remark VDD 3.0 3.3 3.6 V Note 2 AVDD 10.8 11 11.2 V VGH 19.7 20 20.3 V Power voltage Input signal voltage V COM 2.7 (3.7) 4.7 V Note 3 Input logic high voltage VIH 0.7VCC - V CC V Input logic low voltage V IL 0 - 0.3V CC V Note 4 Note 1: Be sure to apply V CC and VGL to the LCD first, and then apply VGH. Note 2: VCC setting should match the signals output voltage (refer to Note 3) of customer’s system board . Note 3:Typical Vcom is only a reference value, it must be optimized according to each LCM. Please use VR and base on below application circuit. Note 4: RESET,STBYB,SELB,L/R,U/D,CABCEN0,CABCEN1.
3.1.2. Current Consumption (GND=AV SS=0V) Values Item Symbol Min. Typ. Max. Unit Remark IGH - 0.25 1.0 mA VGH =20V IGL - 0.25 1.0 mA VGL = -6.8V IDD - 38 60 mA DVDD =3.3V Current for Driver IAVDD - 20 30 mA AVDD =11V 3.1.3. Backlight Driving Conditions Values Item Symbol Min. Typ. Max. Unit Remark Voltage for LED backlight VL - 9.9 10.5 V Note 1 Current for LED backlight IL - 360 420 mA LED life time - - 20,000 - Hr Note 2 Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and I L = 360mA. Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and IL =360mA. The LED lifetime could be decreased if operating IL is lager than 360mA.
3.2. Power Sequence a. Power on: b. Power off: VDD STBYB RESET A VDD VGL VGH LVDS Signal B/L >50ms >=0ms >100ms >=0ms Normal signal VCOM <20ms VDD STBYB RESET A VDD VGL VGH LVDS Signal B/L >120ms >50us >40us >20us <20ms <500us >500us Normal signal VCOM >35ms
3.3. Timing Characteristics 3.3.1. AC Electrical Characteristics Values Parameter Symbol Min. Typ. Max. Unit Remark Clock frequency RxFCLK 20 - 71 MHz Input data skew margin T RSKM 500 - - ps Clock high time T LVCH - 4/(7* R xFCLK) - ns Clock low time TLVCL - 3/(7* R xFCLK) - ns 3.3.2. Input Clock and Data Timing Diagram
3.3.3. DC Electrical Characteristics Values Parameter Symbol Min. Typ. Max. Unit Remark Differential input high Threshold voltage RxVTH - - +0.1 V Differential input low Threshold voltage RxVTL -0.1 - - V RXVCM=1.2V Input voltage range (singled-end) RxVIN 0 - 2.4 V Differential input common mode voltage RxVCM |VID|/2 - 2.4-|V ID|/2 V Differential voltage |VID| 0.2 - 0.6 V Differential input leakage current RVxliz -10 - +10 uA
3.3.4. Timing Values Item Symbol Min. Typ. Max. Unit Remark Clock Frequency fclk 40.8 51.2 67.2 MHz Frame rate =60Hz Horizontal display area thd 1024 DCLK HS period time th 1114 1344 1400 DCLK HS Blanking thb 90 320 376 DCLK Vertical display area Thb+thfp 600 H VS period time tv 610 635 800 H VS Blanking Tvb+tvfp 10 35 200 H
3.3.5. Data Input Format 6bit LVDS input 8bit LVDS input Note: Support DE timing mode only, SYNC mode not supported.
- Optical Specifications Values Item Symbol Condition Min. Typ. Max. Unit Remark θL Φ=180°(9 o’clock) 65 75 - θR Φ=0°(3 o’clock) 65 75 - θT Φ=90°(12 o’clock) 60 70 - Viewing angle (CR≥ 10) θB Φ=270°(6 o’clock) 65 75 - degree Note 1 TON - 10 20 msec Note 3 Response time TOFF - 20 30 msec Note 3 Contrast ratio CR 600 700 - - Note 4 WX 0.26 0.31 0.36 - Color chromaticity WY 0.28 0.33 0.38 - Note 2 Note 5 Note 6 Luminance L 400 500 - cd/m² Note 6 Luminance uniformity YU Normal θ=Φ=0° 70 75 - % Note 7 Test Conditions: 1. V CC=3.3V, IL=360mA (Backlight current), the ambient temperature is 25℃. 2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measure d in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.) Fig. 4-2 Optical measurement system setup Note 3: Definition of Response time Normal line θ=Φ=0° Normal line θ=Φ=0° Photo detector Φ=90° 12 o’clock direction Φ=270° 6 o’clock direction Φ=0° Φ=180° Active Area 500mm LCD Panel Φ=90° 12 o’clock direction Φ=270° 6 o’clock direction Φ=0° Φ=180° Active Area θL θT θB θR
The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Fig. 4-3 Definition of response time Note 4: Definition of contrast ratio state Black"" the on LCD whenmeasured Luminance state White"" the on LCD whenmeasured Luminance(CR) ratio Contrast = Note 5: Definition of color chromaticity (CIE1931 ) Color coordinates measured at center point of LCD. Note 6: Definition of luminance: Measured at the center area of the panel when LCD panel is driven at “white” state. The LED driving condition is IL=360mA . Note 7: Definition of Luminance Uniformity 100% 90% 10% Photo detector output (Relative value) TO N TOF F White (TFT OFF) Black (TFT ON) White (TFT OFF)
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area. max min B B(Yu)Uniformity Luminance = W W/3 W/3 W/6 L/3L/3L/6 L Fig. 4-4 Definition of measuring points Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position.
- Reliability Test Items (Note3) Item Test Conditions Remark High Temperature Storage Ta = 80℃ 240hrs Note 1，Note 4 Low Temperature Storage Ta = -30℃ 240hrs Note 1，Note 4 High Temperature Operation Ts = 80℃ 240hrs Note 2，Note 4 Low Temperature Operation Ta = -20℃ 240hrs Note 1，Note 4 Operate at High Temperature and Humidity +60℃, 90%RH 240hrs Note 4 Thermal Shock -20℃/30 min ~ +80℃/30 min for a total 100 cycles, Start with cold temperature and end with high temperature. Note 4 Vibration Test Frequency range:10~55Hz Stroke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X. Y . Z. (6 hours for total) Mechanical Shock 100G 6ms,±X, ±Y , ±Z 3 times for each direction Package Vibration Test Random Vibration : 0.015G*G/Hz from 5-100HZ, -6dB/Octave from 100-200HZ 2 hours for each direction of X. Y . Z. (6 hours for total) Package Drop Test Height:60 cm 1 corner, 3 edges, 6 surfaces Electro Static Discharge ± 2KV, Human Body Mode, 100pF /1500Ω Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel’s surface. Note 3: In the standard condition, there shall b e no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but don’t guarantee all of the cosmetic specification. Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature.
- General Precautions 6.1. Safety Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water. 6.2. Handling 1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. 2. The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch or other damages. 3. To avoid contamination on the display surface, do not touch the module surface with bare hands. 4. Keep a space so that the LCD panels do not touch other components. 5. Put cover board such as acrylic board on the surface of LCD panel to protect panel from damages. 6. Transparent electrodes may be disconnected if you use the LCD panel under environmental conditions where the condensation of dew occurs. 7. Do not leave module in direct sunlight to avoid malfunction of the ICs. 6.3. Static Electricity 1. Be sure to ground module before turning on power or operating module. 2. Do not apply voltage which exceeds the absolute maximum rating value. 6.4. Storage 1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less. 2. Do not store the module in surroundings contai ning organic solvent or corrosive gas. 3. Store the module in an anti-electrostatic container or bag. 6.5. Cleaning 1. Do not wipe the polarizer with dry cloth. It might cause scratch. 2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might permanent damage to the polarizer.
- Mechanical Drawing
- Package Drawing
8.1 Packaging Material Table
No. Item Model (Material) Dimensions(mm) Unit Weight (kg) Quantity Remark
1 LCM
Module ZJ080NA-08A 192.8 x 116.9 x 6.4 TBD 30pcs
2 Partition BC Corrugated
paper 512 × 349 × 230 1.184 1set
3 Corrugated
paper 251.2x178.6x45.5 0.155 4pcs
4 Dust-Proof
Bag PE 700 × 530 0.060 1pcs 5 A/S Bag PE 213.0 ×182.0 × 0.2 0.003 30pcs
6 Carton Corrugated
paper 530 × 355 × 255 1.100 1pcs
7 Total weight
8.2 Packaging Quantity
Total LCM quantity in Carton: no. of Partition 2 Rows × quantity per Row 15 = 30