DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 58
Technical content
Stereo CODEC for Portable Audio Applications http://www.cirrus.com Copyright Cirrus Logic, Inc., 2008–2016 (All Rights Reserved) Rev 4.2 DEC ‘16 WM8988
DESCRIPTION
The WM8988 is a low power, high quality stereo CODEC designed for portable digital audio applications. The device in tegrates complete interfaces to 2 stereo headphone or line out ports. External component requirements are drastically reduced as no separate headphone amplifiers are required. Advanced on -chip digital signal processing performs graphic equaliser, 3 -D sound enhancement and automatic level control for the microphone or line input. The WM8988 can operate as a master or a slave, with various master clock frequencies including 12 or 24MHz for USB devices, or standard 256f s rates like 12.288MHz and 24.576MHz. Different audio sample rates such as 96kHz, 48kHz, 44.1kHz are generated directly from the master clock without the need for an external PLL. The WM8988 operates at supply voltages down to 1.8V, although the digital core can operate at voltages down to 1.42V to save power, and the maximum for all supplies is 3.6 Volts. Different sections of the chip can also be powered down under software control. The WM8988 is sup plied in a very small and thin 4x4 mm COL package, ideal for use in hand -held and portable systems.
FEATURES
DAC SNR 100dB (‘A’ weighted), THD –90dB at 48kHz, 3.3V ADC SNR 93dB (‘A’ weighted), THD -81dB at 48kHz, 3.3V Programmable ALC / Noise Gate 2x On-chip Headphone Drivers - >40mW output power on 16 / 3.3V - THD –80dB at 20mW, SNR 90dB with 16 load Digital Graphic Equaliser Low Power - 7mW stereo playback (1.8V / 1.5V supplies) - 14mW record and playback (1.8V / 1.5V supplies) Low Supply Voltages - Analogue 1.8V to 3.6V - Digital core: 1.42V to 3.6V - Digital I/O: 1.8V to 3.6V 256fs / 384fs or USB master clock rates: 12MHz, 24MHz Audio sample rates: 8, 11.025, 16, 22.05, 24, 32, 44.1, 48, 88.2, 96kHz generated internally from master clock 4x4mm COL package
APPLICATIONS
Portable Multimedia players Multimedia handsets Handheld gaming BLOCK DIAGRAM LINSEL ANALOGUE MONO MIX CONTROL INTERFACECSB SDIN SCLK MODE WM8988 DCVDD DBVDDDGND LMIXSEL DAC ROUT1VOL LOUT1VOL LOUT1 ROUT1 LOUT2 ROUT2 VREF AVDD AGND VMID 50K50K HPVDDHPGND DAC AUDIO INTERFACE ADCDAT BCLK MCLK DACDAT LRC DIGITAL FILTERS VOLUME DIGITAL MONO MIX ADC ADC DIGITAL FILTERS GRAPHIC EQUALISER BASS BOOST CLOCK CIRCUITRY LINPUT2 LINPUT1 LI2LO RI2LO LI2RO RI2RO LD2LO RD2LO LD2RO RD2RO LEFT MIXER RIGHT MIXER ROUT2VOL LOUT2VOL PGA + MIC BOOST M U X M U X DIFF. INPUT L1-R1 OR L2-R2 DC MEASUREMENT RINSEL RMIXSEL RINPUT2 RINPUT1 PGA + MIC BOOST M U X M U X DC MEASUREMENT LCOM (headphone / line output (headphone / line output (headphone / line output (headphone / line output HPCOM
2 Rev 4.2 TABLE OF CONTENTS
Rev 4.2 3 PIN CONFIGURATION 141312111098 22232425262728 WM8988 – Top View DACDAT BCLK DCVDD DGND DBVDD MCLK LRC AVDD VMID AGND VREF HPGND ADCDAT LCOM HPVDD ROUT1 LOUT1 ROUT2 LOUT2 HPCOM CSB MODE LINPUT2 LINPUT1 RINPUT1 RINPUT2 SDIN SCLK
ORDERING INFORMATION
WM8988LGECN/V -25°C to +85°C 28-lead COL QFN (4x4x0.55mm, lead-free) MSL3 260°C WM8988LGECN/RV -25°C to +85°C 28-lead COL QFN (4x4x0.55mm, lead-free) Tape and reel MSL3 260°C Note: Reel quantity = 3,500
4 Rev 4.2 PIN DESCRIPTION PIN NO NAME TYPE DESCRIPTION
1 MCLK Digital Input Master Clock
2 DCVDD Supply Digital Core Supply
3 DBVDD Supply Digital Buffer (I/O) Supply
4 DGND Supply Digital Ground (return path for both DCVDD and DBVDD)
5 BCLK Digital Input / Output Audio Interface Bit Clock
6 DACDAT Digital Input DAC Digital Audio Data
7 LRC Digital Input / Output Audio Interface Left / Right Clock
8 ADCDAT Digital Output ADC Digital Audio Data
9 HPCOM Analogue Input LOUT1 and ROUT1 common mode feedback
10 LCOM Analogue Input LOUT2 and ROUT2 common mode feedback
11 ROUT1 Analogue Output Right Output 1 (Line or Headphone)
12 LOUT1 Analogue Output Left Output 1 (Line or Headphone)
13 HPGND Supply Supply for Analogue Output Drivers (LOUT1/2, ROUT1/2)
14 ROUT2 Analogue Output Right Output 1 (Line or Headphone )
15 LOUT2 Analogue Output Left Output 1 (Line or Headphone)
16 HPVDD Supply Supply for Analogue Output Drivers (LOUT1/2, ROUT1/2, MONOUT)
17 AVDD Supply Analogue Supply
18 AGND Supply Analogue Ground (return path for AVDD)
19 VREF Analogue Output Reference Voltage Decoupling Capacitor
20 VMID Analogue Output Midrail Voltage Decoupling Capacitor
21 RINPUT2 Analogue Input Right Channel Input 2
22 LINPUT2 Analogue Input Left Channel Input 2
23 RINPUT1 Analogue Input Right Channel Input 1
24 LINPUT1 Analogue Input Left Channel Input 1
25 MODE Digital Input Control Interface Selection
26 CSB Digital Input Chip Select / Device Address Selection
27 SDIN Digital Input/Output Control Interface Data Input / 2-wire Acknowledge output
28 SCLK Digital Input Control Interface Clock Input
Rev 4.2 5 ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Cirrus Logic tests its package types accordin g to IPC/JEDEC J -STD-020 for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION MIN MAX Supply voltages -0.3V +4.5V Voltage range digital inputs DGND -0.3V DBVDD +0.3V Voltage range analogue inputs AGND -0.3V AVDD +0.3V Operating temperature range, TA -25C +85C Storage temperature after soldering -65C +150C Notes 1. Analogue and digital grounds must always be within 0.3V of each other. 2. All digital and analogue supplies are completely independent from each other. 3. DCVDD must be less than or equal to AVDD and DBVDD. RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN TYP MAX UNIT Digital supply range (Core) DCVDD 1.42 3.6 V Digital supply range (Buffer) DBVDD 1.7 3.6 V Analogue supplies range AVDD, HPVDD 1.8 3.6 V Ground DGND,AGND, HPGND 0 V
6 Rev 4.2
ELECTRICAL CHARACTERISTICS
DCVDD = 1.5V, DBVDD = 2.4V, AVDD = HPVDD =2.4V, TA = +25oC, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Analogue Inputs (LINPUT1, RINPUT1, LINPUT2, RINPUT2) to ADC out Full Scale Input Signal Level (for ADC 0dB Input at 0dB Gain) VINFS AVDD = 3.3V 0.95 1.0 1.05 Vrms AVDD = 2.4V 0.690 0.727 0.763 AVDD = 1.8V 0.480 0.545 0.610 Input Resistance RIN L/RINPUT1 to ADC, PGA gain = 0dB 16 22 k L/RINPUT1 to ADC, PGA gain = +30dB 1.5 2.8 L/RINPUT2 to ADC PGA gain = 0dB 16 22 L/RINPUT2 to ADC PGA gain = 30dB 1.5 2.8 Input Capacitance 10 pF Signal to Noise Ratio (A-weighted) SNR AVDD = 3.3V 80 93 dB AVDD = 2.4V 80 88 AVDD = 1.8V 78 87 Total Harmonic Distortion THD -1dBFs input, AVDD = 3.3V -81 -68 dB -1dBFS input, AVDD = 2.4V -80 -68 -1dBFs input, AVDD = 1.8V -76 -65 Total Harmonic Distortion + Noise THD+N -1dBFs input, AVDD = 3.3V -75 -65 dB -1dBFS input, AVDD = 2.4V -70 -65 -1dBFs input, AVDD = 1.8V -70 -60 ADC Channel Separation 1kHz signal 85 dB 10kHz signal 85 Channel Matching 1kHz signal -0.5 0.2 +0.5 dB Analogue Outputs (LOUT1/2, ROUT1/2) 0dB Full scale output voltage VOUTFS AVDD = 3.3V 0.95 1.0 1.05 Vrms AVDD = 2.4V 0.690 0.727 0.763 AVDD = 1.8V 0.507 0.545 0.583 Mute attenuation 1kHz, full scale signal 90 dB Channel Separation 1kHz signal 85 dB 10kHz signal 85 PGA Gain range guaranteed monotonic +6 -67 dB PGA step size 0.25 1 1.25 dB
Rev 4.2 7 Test Conditions DCVDD = 1.5V, DBVDD = 2.4V, AVDD = HPVDD =2.4V, TA = +25oC, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT DAC to Line-Out (L/ROUT1 or L/ROUT2 with 10k / 50pF load) Signal to Noise Ratio (A-weighted) SNR AVDD=3.3V HPCOM= LCOM=0 DACMIXBIAS=0 88 100 dB DACMIXBIAS=1 99 AVDD = 2.4V HPCOM= LCOM=1 DACMIXBIAS=0 97 DACMIXBIAS=1 88 96 AVDD=1.8V HPCOM= LCOM=0 DACMIXBIAS=0 96 DACMIXBIAS=1 85 95 Total Harmonic Distortion THD AVDD=3.3V HPCOM= LCOM=0 DACMIXBIAS=0 -90 -75 dB DACMIXBIAS=1 -89 AVDD = 2.4V HPCOM= LCOM=1 DACMIXBIAS=0 -83 DACMIXBIAS=1 -82 -75 AVDD=1.8V HPCOM= LCOM=0 DACMIXBIAS=0 -80 DACMIXBIAS=1 -79 -65 Total Harmonic Distortion + Noise THD+N AVDD=3.3V HPCOM= LCOM=0 DACMIXBIAS=0 -88 -70 dB DACMIXBIAS=1 -87 AVDD = 2.4V HPCOM= LCOM=1 DACMIXBIAS=0 -75 DACMIXBIAS=1 -74 -70 AVDD=1.8V HPCOM= LCOM=0 DACMIXBIAS=0 -75 DACMIXBIAS=1 -74 -65 Channel Separation 1kHz signal 100 dB 10kHz signal 85 Ground noise rejection 10mV, 20kHz noise on LCOM/HPCOM, LCOM/HPCOM enabled 40 dB
8 Rev 4.2 Test Conditions DCVDD = 1.5V, DBVDD = 2.4V, AVDD = HPVDD =2.4V, TA = +25oC, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Headphone Output (LOUT1/ROUT1, LOUT2/ROUT2 AC coupled to load) Output Power per channel PO Output power is very closely correlated with THD; see below. Total Harmonic Distortion THD HPVDD=1.8V, RL=32 PO=5mW HPCOM=LCOM=0 DACMIXBIAS=1 0.013 -78 dB HPVDD=1.8V, RL=16 PO=5mW HPCOM=LCOM=0 DACMIXBIAS=1 0.010 -80 dB HPVDD=2.4V, RL=32, PO=5mW HPCOM=LCOM=1 DACMIXBIAS=1 0.010 -80 dB HPVDD=2.4V, RL=16, PO=5mW HPCOM=LCOM=1 DACMIXBIAS=1 0.013 -78 0.032 -70 dB HPVDD=3.3V, RL=32, PO=20mW HPCOM=LCOM=0 DACMIXBIAS=0 0.010 -82 dB HPVDD=3.3V, RL=16, PO=20mW HPCOM=LCOM=0 DACMIXBIAS=0 0.010 -80 dB Total Harmonic Distortion + Noise THD+N HPVDD=1.8V, RL=32 PO=5mW HPCOM=LCOM=0 DACMIXBIAS=1 -80 dB HPVDD=1.8V, RL=16 PO=5mW HPCOM=LCOM=0 DACMIXBIAS=1 -78 dB HPVDD=2.4V, RL=32, PO=5mW HPCOM=LCOM=1 DACMIXBIAS=1 -79 dB HPVDD=2.4V, RL=16, PO=5mW HPCOM=LCOM=1 DACMIXBIAS=1 -77 -65 dB HPVDD=3.3V, RL=32, PO=20mW HPCOM=LCOM=0 DACMIXBIAS=0 -80 dB HPVDD=3.3V, RL=16, PO=20mW HPCOM=LCOM=0 DACMIXBIAS=0 -78 dB
Rev 4.2 9 Test Conditions DCVDD = 1.5V, DBVDD = 2.4V, AVDD = HPVDD =2.4V, TA = +25oC, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Signal to Noise Ratio (A-weighted) SNR HPVDD = 3.3V HPCOM=LCOM=0 DACMIXBIAS=1 100 dB HPVDD = 2.4V HPCOM=LCOM=1 DACMIXBIAS=1 90 96 dB HPVDD = 1.8V HPCOM=LCOM=0 DACMIXBIAS=0 96 dB Headphone Output Ground noise rejection 10mV, 20kHz noise on HPCOM, HPCOM enabled 40 dB Line Output Ground Noise Rejection 10mV, 20kHz noise on LCOM, LCOM enabled 40 dB Analogue Reference Levels Midrail Reference Voltage VMID –3% AVDD/2 +3% V Buffered Reference Voltage VREF –3% AVDD/2 +3% V Digital Input / Output Input HIGH Level VIH 0.7DB VDD V Input LOW Level VIL 0.3DBVDD V Output HIGH Level VOH IOH = +1mA 0.9DB VDD V Output LOW Level VOL IOL = -1mA 0.1DBVDD V
10 Rev 4.2 POWER CONSUMPTION The power consumption of the WM8988 depends on the following factors. Supply voltages: Reducing the supply voltages also reduces supply currents, and therefore results in significant power savings, especially in the digital sections of the WM8988. Operating mode: Significant power savings can be achieved by always disabling parts of the WM8988 that are not used (e.g. mic pre-amps, unused outputs, DAC, ADC, etc.) SCENARIO DETAIL AVDD POWER (MW) HPVDD POWER (MW) DCVDD POWER (MW) DBVDD POWER (MW) TOTAL POWER (MW) Playback to Headphone 32ohm -50dB (near silence) Playback to Headphone 32ohm -21dB (0.1mW/channel) Playback to Headphone 32ohm -9dB (2mW/channel) Table 1 Power Consumption for 2.4v / 1.8v Supplies SCENARIO DETAIL AVDD POWER (MW) HPVDD POWER (MW) DCVDD POWER (MW) DBVDD POWER (MW) TOTAL POWER (MW) Playback to Headphone 32ohm -50dB (near silence) Playback to Headphone 32ohm -24dB (0.1mW/channel) Playback to Headphone 32ohm -11dB (2mW/channel) Table 2 Power Consumption for 3.0v / 1.8v Supplies Notes: 1. All figures are at TA = +25oC, Slave Mode, fs = 48kHz, MCLK = 12.288 MHz (256fs), 2. The power dissipated in the headphone is not included in the above table.
Rev 4.2 11 SIGNAL TIMING REQUIREMENTS SYSTEM CLOCK TIMING MCLK tMCLKL tMCLKH tMCLKY Figure 1 System Clock Timing Requirements Test Conditions CLKDIV2=0, DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode fs = 48kHz, MCLK = 384fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT System Clock Timing Information MCLK System clock pulse width high TMCLKL 21 ns MCLK System clock pulse width low TMCLKH 21 ns MCLK System clock cycle time TMCLKY 54 ns MCLK duty cycle TMCLKDS 60:40 40:60 Test Conditions CLKDIV2=1, DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode fs = 48kHz, MCLK = 384fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT System Clock Timing Information MCLK System clock pulse width high TMCLKL 10 ns MCLK System clock pulse width low TMCLKH 10 ns MCLK System clock cycle time TMCLKY 27 ns
12 Rev 4.2 AUDIO INTERFACE TIMING – MASTER MODE Figure 2 Digital Audio Data Timing – Master Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Bit Clock Timing Information BCLK rise time (10pF load) tBCLKR 3 ns BCLK fall time (10pF load) tBCLKF 3 ns BCLK duty cycle (normal mode, BCLK = MCLK/n) tBCLKDS 50:50 BCLK duty cycle (USB mode, BCLK = MCLK) tBCLKDS TMCLKDS Audio Data Input Timing Information DACLRC propagation delay from BCLK falling edge tDL 10 ns ADCDAT propagation delay from BCLK falling edge tDDA 10 ns DACDAT setup time to BCLK rising edge tDST 10 ns DACDAT hold time from BCLK rising edge tDHT 10 ns BCLK (Output) ADCDAT LRC (Output) t DL DACDAT t DDA t DHT t DST
Rev 4.2 13 AUDIO INTERFACE TIMING – SLAVE MODE Figure 3 Digital Audio Data Timing – Slave Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information BCLK cycle time tBCY 50 ns BCLK pulse width high tBCH 20 ns BCLK pulse width low tBCL 20 ns DACLRC set-up time to BCLK rising edge tLRSU 10 ns DACLRC hold time from BCLK rising edge tLRH 10 ns DACDAT hold time from BCLK rising edge tDH 10 ns ADCDAT propagation delay from BCLK falling edge tDD 10 ns Note: BCLK period should always be greater than or equal to MCLK period. BCLK LRC t BCH t BCL t BCY DACDAT ADCDAT t LRSU t DS t LRH t DH t DD
14 Rev 4.2 CONTROL INTERFACE TIMING – 3-WIRE MODE CSB SCLK SDIN tCSL tDHOtDSU tCSH tSCY tSCH tSCL tSCS LSB tCSS Figure 4 Control Interface Timing – 3-Wire Serial Control Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK rising edge to CSB rising edge tSCS 80 ns SCLK pulse cycle time tSCY 200 ns SCLK pulse width low tSCL 80 ns SCLK pulse width high tSCH 80 ns SDIN to SCLK set-up time tDSU 40 ns SCLK to SDIN hold time tDHO 40 ns CSB pulse width low tCSL 40 ns CSB pulse width high tCSH 40 ns CSB rising to SCLK rising tCSS 40 ns Pulse width of spikes that will be suppressed tps 0 5 ns
Rev 4.2 15 CONTROL INTERFACE TIMING – 2-WIRE MODE SDIN SCLK t6 t2 Figure 5 Control Interface Timing – 2-Wire Serial Control Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25oC, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK Frequency 0 526 kHz SCLK Low Pulse-Width t1 1.3 us SCLK High Pulse-Width t2 600 ns Hold Time (Start Condition) t3 600 ns Setup Time (Start Condition) t4 600 ns Data Setup Time t5 100 ns SDIN, SCLK Rise Time t6 300 ns SDIN, SCLK Fall Time t7 300 ns Setup Time (Stop Condition) t8 600 ns Data Hold Time t9 900 ns Pulse width of spikes that will be suppressed tps 0 5 ns
Rev 4.2 17 DEVICE DESCRIPTION INTRODUCTION The WM8988 is a low power audio CODEC offering a combination of high quality audio, advanced features, low power and small size. These characteristics make it ideal for portable digital audio applications such as MP3 and minidisk player / recorders. Stereo 24-bit multi-bit delta sigma ADC s and DACs are used with oversampling digital interpolation and decimation filters. The device includes three stereo analogue inputs that can be switched internally. Each can be used as either a line level input or microphone input and LINPUT1/RINPUT1 and LINPUT2/RINPUT2 can be configured as mono differential inputs. A programmable gain amplifier with automatic level control (ALC) keeps the recording volume constant. The on -chip stereo ADC and DAC are of a high quality using a multi-bit, low-order oversampling architecture to deliver optimum performance with low power consumption. The DAC output signal first enters an analogue mixer where an analogue input and/or the post -ALC signal can be added to it. This mix is available on line and headphone outputs. The WM8988 has a configurable digital audio interface where ADC data can be read and digital audio playback data fed to the DAC. It supports a number of audio data formats including I 2S, DSP Mode (a burst mode in which frame sync plus 2 data packed words are transmitted), MSB-First, left justified and can operate in master or slave modes. The WM8988 uses a unique clocking scheme that can generate many commonly used audio sample rates from either a 12.00MHz USB clock or an industry standard 256/384 f s clock. T his feature eliminates the common requirement for an external phase -locked loop (PLL) in applications where the master clock is not an integer multiple of the sample rate. Sample rates of 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kH z, 88.2kHz and 96kHz can be generated. The digital filters used for recording and playback are optimised for each sampling rate used. To allow full software control over all its features, the WM8988 offers a choice of 2 or 3 wire MPU control interface. It is fully compatible and an ideal partner for a wide range of industry standard microprocessors, controllers and DSPs. The design of the WM8988 has given much attention to power consumption without compromising performance. It operates at very low voltages, and includes the ability to power off parts of the circuitry under software control, including standby and power off modes. INPUT SIGNAL PATH The input signal path for each channel consists of a switch to select between three analogue inputs, followed by a PGA (programmable gain amplifier) and an optional microphone gain boost. A differential input of either (LINPUT1 – RINPUT1) or (LINPUT2 – RINPUT2) may also be selected. The gain of the PGA can be controlled either by the user or by the on -chip ALC funct ion (see Automatic Level Control). The signal then enters an ADC where it is digitised. Alternatively, the two channels can also be mixed in the analogue domain and digitised in one ADC while the other ADC is switched off. The mono -mix signal appears on both digital output channels. SIGNAL INPUTS The WM8988 has two sets of high impedance, low capacitance AC coupled analogue inputs, LINPUT1/RINPUT1 and LINPUT2/RINPUT2. Inputs can be configured as microphone or line level by enabling or disabling the microphone gain boost. LINSEL and RINSEL control bits (see Table 4) are used to select independently between external inputs and internally generated differential products (LINPUT1 -RINPUT1 or LINPUT2-RINPUT2). The choice of differential signal, LINPUT1 -RINPUT1 or LINPUT2 -RINPUT2 is made using DS (refer to Table 6). As an example, the WM8988 can be set up to convert one differential and one single ended mono signal by applying the differential signal to LINPUT1/RINPUT 1 and the single ended signal to
18 Rev 4.2 RINPUT2. By setting LINSEL to L-R Differential (see Table 4), DS to LINPUT1 – RINPUT1 (see Table 6) and RINSEL to RINPUT2, each mono signal can then be routed to a separate ADC or Bypass path. The signal inputs are biased internally to the reference voltage VREF. Whenever the line inputs are muted or the device placed into standby mode, the inputs are kept biased to VREF using special anti - thump circuitry. This reduces any audible clicks that may otherwise be heard when changing inputs. DC MEASUREMENT For DC measurements (for example, battery voltage monitoring), the input signal at the LINPUT1 and/or RINPUT1 pins can be taken directly into the respective ADC, bypassing both PGA and microphone boost. The ADC output then becomes unsigned relative to AVDD, instead of being a signed (two’s complement) number relative to VREF. Setting L/RDCM will override L/RINSEL. The input range for dc measurement is AGND to AVDD. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R32 (20h) ADC Signal Path Control (Left) 7:6 LINSEL 00 Left Channel Input Select 00 = LINPUT1 01 = LINPUT2 10 = Reserved 11 = L-R Differential (either LINPUT1- RINPUT1 or LINPUT2-RINPUT2, selected by DS) 5:4 LMICBOOST 00 Left Channel Microphone Gain Boost 00 = Boost off (bypassed) 01 = 13dB boost 10 = 20dB boost 11 = 29dB boost R33 (21h) ADC Signal Path Control (Right) 7:6 RINSEL 00 Right Channel Input Select 00 = RINPUT1 01 = RINPUT2 10 = Reserved 11 = L-R Differential (either LINPUT1- RINPUT1 or LINPUT2-RINPUT2, selected by DS) 5:4 RMICBOOST 00 Right Channel Microphone Gain Boost 00 = Boost off (bypassed) 01 = 13dB boost 10 = 20dB boost 11 = 29dB boost Table 4 Input Software Control REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R31 (1Fh) ADC input Mode
5 RDCM 0 Right Channel DC Measurement
0 = Normal Operation, PGA Enabled 1 = Measure DC level on RINPUT1
4 LDCM 0 Left Channel DC Measurement
0 = Normal Operation, PGA Enabled 1 = Measure DC level on LINPUT1 Table 5 DC Measurement Select
Rev 4.2 19 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R31 (1Fh) ADC Input Mode
8 DS 0 Differential input select
0: LINPUT1 – RINPUT1 1: LINPUT2 – RINPUT2 Table 6 Differential Input Select MONO MIXING The stereo ADC can operate as a stereo or mono device, or the two channels can be mixed to mono, either in the analogue domain (i.e. before the ADC) or in the digital domain (after the ADC). MONOMIX selects the mode of operation. For analogue mono mix either the left or right channel ADC can be used, allowing the unused ADC to be powered off or used for a dc measurement conversion. The user also has the flexibility to select the data output from the audio interface using DATSEL . The default is for left and right channel ADC data to be output, but the interface may also be configured so that e.g. left channel ADC data is output as both left and right data for when an analogue mono mix is selected. Note: If DC measurement is selected this overrides the MONOMIX selection. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R31 (1Fh) ADC input Mode 7:6 MONOMIX [1:0] 00 00: Stereo 01: Analogue Mono Mix (using left ADC) 10: Analogue Mono Mix (using right ADC) 11: Digital Mono Mix Table 7 Mono Mixing REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R23 (17h) Additional Control (1) 3:2 DATSEL [1:0] 00 00: left data=left ADC; right data =right ADC 01: left data =left ADC; right data = left ADC 10: left data = right ADC; right data =right ADC 11: left data = right ADC; right data = left ADC Table 8 ADC Data Output Configuration PGA CONTROL The PGA matches the input signal level to the ADC input range. The PGA gain is logarithmically adjustable from +30dB to –17.25dB in 0.75dB steps. Each PGA can be controlled either by the user or by the ALC function (see Automatic Level Control). When ALC is enabled for one or both channels, then writing to the corresponding PGA control register has no effect. The gain is independently adjustable on both Right and Left Line Inputs. Additionally, by controlling the register bits LIVU and RIVU, the left and right gain settings can be simultaneously updated. Setting the LZCEN and RZCEN bits enables a zero -cross det ector which ensures that PGA gain changes only occur when the signal is at zero, eliminating any zipper noise. If zero cross is enabled a timeout is also available to update the gain if a zero cross does not occur. This function may be enabled by setting TOEN in register R23 (17h). The inputs can also be muted in the analogue domain under software control. The software control registers are shown in Table 9. If zero crossing is enabled, it is necessary to enable zero cross timeout to un-mute the input PGAs. This is because their outputs will not cross zero when muted. Alternatively, zero cross can be disabled before sending the un-mute command.
20 Rev 4.2 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R0 (00h) Left Channel PGA
8 LIVU 0 Left Volume Update
0 = Store LINVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LINVOL, right = intermediate latch)
7 LINMUTE 1 Left Channel Input Analogue Mute
1 = Enable Mute 0 = Disable Mute Note: LIVU must be set to un-mute.
6 LZCEN 0 Left Channel Zero Cross Detector
1 = Change gain on zero cross only 0 = Change gain immediately 5:0 LINVOL [5:0] 010111 ( 0dB ) Left Channel Input Volume Control 111111 = +30dB 111110 = +29.25dB . . 0.75dB steps down to 000000 = -17.25dB R1 (01h) Right Channel PGA
8 RIVU 0 Right Volume Update
0 = Store RINVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (right = RINVOL, left = intermediate latch)
7 RINMUTE 1 Right Channel Input Analogue Mute
1 = Enable Mute 0 = Disable Mute Note: RIVU must be set to un-mute.
6 RZCEN 0 Right Channel Zero Cross Detector
1 = Change gain on zero cross only 0 = Change gain immediately 5:0 RINVOL [5:0] 010111 ( 0dB ) Right Channel Input Volume Control 111111 = +30dB 111110 = +29.25dB . . 0.75dB steps down to 000000 = -17.25dB R23 (17h) Additional Control (1)
0 TOEN 0 Timeout Enable
0 : Timeout Disabled 1 : Timeout Enabled Table 9 Input PGA Software Control ANALOGUE TO DIGITAL CONVERTER (ADC) The WM8988 uses a multi -bit, oversampled sigma -delta ADC for each channel. The use of multi -bit feedback and high oversampling rates reduces the effects of jitter and high frequency noise. The ADC Full Scale input level is proportional to AVDD. With a 3.3V supply voltage, the full scale level is 1.0 Volts r.m.s. Any voltage greater than full scale may overload the ADC and cause distortion.
Rev 4.2 21 ADC DIGITAL FILTER The ADC filters perform true 24 -bit signal processing to convert the raw multi -bit oversampled data from the ADC to the correct sampling frequency to be output on the digital audio interface. The digital filter path is illustrated in Figure 8. FROM ADC DIGITAL HPF DIGITAL FILTER TO DIGITAL AUDIO INTERFACE DIGITAL DECIMATOR ADCHPD Figure 8 ADC Digital Filter The ADC digital filters contain a digital high -pass filter, selectable via software control. The high -pass filter response is detailed in the Digital Filter Characteristics section. When the high -pass filter is enabled the DC offset is continuously calculate d and subtracted from the input signal. By setting HPOR, the last calculated DC offset value is stored when the high -pass filter is disabled and will continue to be subtracted from the input signal. If the DC offset is changed, the stored and subtracted value will not change unless the high -pass filter is enabled. This feature can be used for calibration purposes. In addition the high -pass filter may be enabled separately on the left and right channels (see Table 11). The output dat a format can be programmed by the user to accommodate stereo or monophonic recording on both inputs. The polarity of the output signal can also be changed under software control. The software control is shown in Table 10. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R5 (05h) ADC and DAC Control 6:5 ADCPOL [1:0] 00 00 = Polarity not inverted 01 = L polarity invert 10 = R polarity invert 11 = L and R polarity invert
4 HPOR 0 Store dc offset when high-pass
1 = store offset 0 = clear offset
0 ADCHPD 0 ADCHPD and HPFLREN together
determine high-pass filter behaviour (see Table 11) R27 (1Bh) 5 HPFLREN 0 Table 10 ADC Signal Path Control HPFLREN ADCHPD LEFT CHANNEL RIGHT CHANNEL 0 0 HPF ON HPF ON 0 1 HPF OFF HPF OFF 1 0 HPF ON HPF OFF 1 1 HPF OFF HPF ON Table 11 ADC High Pass Filter Modes
22 Rev 4.2 DIGITAL ADC VOLUME CONTROL The output of the ADCs can be digitally amplified or attenuated over a range from –97dB to +30dB in 0.5dB steps. The volume of each channel can be controlled separately. The gain for a given eight -bit code X is given by: 0.5 (X-195) dB for 1 X 255; MUTE for X = 0 The LAVU and RAVU control bits control the loading of digi tal volume control data. When LAVU or RAVU are set to 0, the LADCVOL or RADCVOL control data will be loaded into the respective control register, but will not actually change the digital gain setting. Both left and right gain settings are updated when eith er LAVU or RAVU are set to 1. This makes it possible to update the gain of both channels simultaneously. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R21 (15h) Left ADC Digital Volume 7:0 LADCVOL [7:0] 11000011 ( 0dB ) Left ADC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -97dB 0000 0010 = -96.5dB ... 0.5dB steps up to 1111 1111 = +30dB
8 LAVU 0 Left ADC Volume Update
0 = Store LADCVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LADCVOL, right = intermediate latch) R22 (16h) Right ADC Digital Volume 7:0 RADCVOL [7:0] 11000011 ( 0dB ) Right ADC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -97dB 0000 0010 = -96.5dB ... 0.5dB steps up to 1111 1111 = +30dB
8 RAVU 0 Right ADC Volume Update
0 = Store RADCVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = RADCVOL) Table 12 ADC Digital Volume Control
Rev 4.2 23 AUTOMATIC LEVEL CONTROL (ALC) The WM8988 has an automatic level control that aims to keep a constant recording volume irrespective of the input signal level. This is achieved by continuously adjusting the PGA gain so that the signal level at the ADC input remains constant. A digital peak detector mon itors the ADC output and changes the PGA gain if necessary. Note that when the ALC function is enabled, the settings of registers 0 and 1 (LINVOL, LIVU, LIZC, LINMUTE, RINVOL, RIVU, RIZC and RINMUTE) are ignored. hold time decay time attack time input signal signal after ALC PGA gain ALC target level Figure 9 ALC Operation The ALC function is enabled using the ALCSEL control bits. When enabled, the recording volume can be programmed between –6dB and –28.5dB (relative to ADC full scale) using the ALCL register bits. An upper limit for the PGA gain can be imposed by setting the MAXGAIN control bits. HLD, DCY and ATK control the hold, decay and attack times, respectively: Hold time is the time delay between the peak level detected being below target and the PGA gain applies to gain ramp -up, there is no delay before ramping the gain down when the signal level is above target. Decay (Gain Ramp-Up) Time is the time that it takes for the PGA gain to ramp up across 90% of its range (e.g. from –15B up to 27.75dB). The time it takes for the recording level to return to its target value therefore depends on both the decay time and on the gain adjustment required. If the gain adjustment is small, it will be shorter than the decay time. The decay time can be programmed in power-of-two (2n) steps, from 24ms, 48ms, 96ms, etc. to 24.58s. Attack (Gain Ramp-Down) Time is the time that it takes for the PGA gain to ramp down across 90% of its range (e.g. from 27.75dB down to -15B gain). The time it takes for the recording level to return to its target value therefore depends on both the attack time and on the gain adjustment required. If the gain adjustment is small, it will be shorter than the attack time. The attack time can be programmed in power-of-two (2n) steps, from 6ms, 12ms, 24ms, etc. to 6.14s. When operating in stereo, the peak detector takes the maximum of left and right channel peak values, and any new gain setting is applied to both left and right PGAs, so that the stereo image is preserved. However, the ALC function can also be enabled on one channel only. In this case, only one PGA is controlled by the ALC mechanism, while the other chann el runs independently with its PGA gain set through the control register. When one ADC channel is unused or used for DC measurement, the peak detector disregards that channel. The ALC function can also operate when the two ADC outputs are mixed to mono in the digital domain, but not if they are mixed to mono in the analogue domain, before entering the ADCs.
24 Rev 4.2 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R17 (11h) ALC Control 1 8:7 ALCSEL [1:0] (OFF) ALC function select 00 = ALC off (PGA gain set by register) 01 = Right channel only 10 = Left channel only 11 = Stereo (PGA registers unused) Note: ensure that LINVOL and RINVOL settings (reg. 0 and 1) are the same before entering this mode. 6:4 MAXGAIN [2:0] 111 (+30dB) Set Maximum Gain of PGA 111 : +30dB 110 : +24dB ….(-6dB steps) 001 : -6dB 000 : -12dB 3:0 ALCL [3:0] 1011 (-12dB) ALC target – sets signal level at ADC input 0000 = -28.5dB FS 0001 = -27.0dB FS … (1.5dB steps) 1110 = -7.5dB FS 1111 = -6dB FS R18 (12h) ALC Control 2
7 ALCZC 0 (zero
cross off) ALC uses zero cross detection circuit. 3:0 HLD [3:0] 0000 (0ms) ALC hold time before gain is increased. 0000 = 0ms 0001 = 2.67ms 0010 = 5.33ms … (time doubles with every step) 1111 = 43.7s R19 (13h) ALC Control 3 7:4 DCY [3:0] 0011 (192ms) ALC decay (gain ramp-up) time 0000 = 24ms 0001 = 48ms 0010 = 96ms … (time doubles with every step) 1010 or higher = 24.58s 3:0 ATK [3:0] 0010 (24ms) ALC attack (gain ramp-down) time 0000 = 6ms 0001 = 12ms 0010 = 24ms … (time doubles with every step) 1010 or higher = 6.14s Table 13 ALC Control PEAK LIMITER To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a limiter function. If the ADC input signal exceeds 87.5% of full scale (–1.16dB), the PGA gain is ramped down at the maximum attack rate (as when ATK = 0000), until the signal level falls below 87.5% of full scale. This function is automatically enabled whenever the ALC is enabled. Note: If ATK = 0000, then the limiter makes no dif ference to the operation of the ALC. It is designed to prevent clipping when long attack times are used.
Rev 4.2 25 NOISE GATE When the signal is very quiet and consists mainly of noise, the ALC function may cause “noise pumping”, i.e. loud hissing noise during sile nce periods. The WM8988 has a noise gate function that prevents noise pumping by comparing the signal level at the LINPUT1/2 and/or RINPUT1/2 pins against a noise gate threshold, NGTH. The noise gate cuts in when: Signal level at ADC [dB] < NGTH [dB] + PGA gain [dB] + Mic Boost gain [dB] This is equivalent to: Signal level at input pin [dB] < NGTH [dB] The ADC output can then either be muted or alternatively, the PGA gain can be held constant (preventing it from ramping up as it normally would when the signal is quiet). The table below summarises the noise gate control register. The NGTH control bits set the noise gate threshold with respect to the ADC full-scale range. The threshold is adjusted in 1.5dB steps. Levels at the extremes of the range may cau se inappropriate operation, so care should be taken with set –up of the function. Note that the noise gate only works in conjunction with the ALC function, and always operates on the same channel(s) as the ALC (left, right, both, or none). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R20 (14h) Noise Gate Control 7:3 NGTH [4:0]
00000 Noise gate threshold
13 -76.5dBfs 13 -75dBfs … 1.5 dB steps 11110 -31.5dBfs 11111 -30dBfs 2:1 NGG [1:0]
00 Noise gate type
X0 = PGA gain held constant 01 = mute ADC output 11 = reserved (do not use this setting)
0 NGAT 0 Noise gate function enable
1 = enable 0 = disable Table 14 Noise Gate Control Note: The performance of the ADC may degrade at high input signal levels if the monitor bypass mux is selected with MIC boost and ALC enabled.
26 Rev 4.2 3D STEREO ENHANCEMENT The WM8988 has a digital 3D enhancement option to artificially increase the separation between the left and right channels. This effect can be used for recording or playback, but not for bo th simultaneously. Selection of 3D for record or playback is controlled by register bit MODE3D. Important: Switching the 3D filter from record to playback or from playback to record may only be done when ADC and DAC are disabled. The WM8988 control interface will only allow MODE3D to be changed when ADC and DAC are disabled (i.e. bits ADCL, ADCR, DACL and DACR in reg. 26 / 1Ah are all zero). The 3D enhancement function is activated by the 3DEN bit, and has two programmable parameters. The 3DDEPTH setting c ontrols the degree of stereo expansion. Additionally, one of four filter characteristics can be selected for the 3D processing, using the 3DVC and 3DLC control bits. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R16 (10h) 3D enhance
7 MODE3D 0 Playback/Record 3D select
0 = 3D selected for Record 1 = 3D selected for Playback 6 3DUC 0 Upper Cut-off frequency 0 = High (2.2kHz at 48kHz sampling) 1 = Low (1.5kHz at 48kHz sampling) 5 3DLC 0 Lower Cut-off frequency 0 = Low (200Hz at 48kHz sampling) 1 = High (500Hz at 48kHz sampling) 4:1 3DDEPTH [3:0]
0000 Stereo depth
0000: 0% (minimum 3D effect) 0001: 6.67% .... 1110: 93.3% 1111: 100% (maximum 3D effect) 0 3DEN 0 3D function enable 1: enabled 0: disabled Table 15 3D Stereo Enhancement Function When 3D enhancement is enabled (and/or the graphic equaliser for playback) it may be necessary to attenuate the signal by 6dB to avoid limiting. This is a user selectable function, enabled by setting ADCDIV2 for the record path and DACDIV2 for the playback path. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R5 (05h) ADC and DAC control
8 ADCDIV2 0 ADC 6dB attenuate enable
0 = disabled (0dB) 1 = -6dB enabled
7 DACDIV2 0 DAC 6dB attenuate enable
0 = disabled (0dB) 1 = -6dB enabled Table 16 ADC and DAC 6dB Attenuation Select
Rev 4.2 27 OUTPUT SIGNAL PATH The WM8988 output signal paths consist of digital filters, DACs, analogue mixers and output drivers. The digital filters and DACs are enabled when the WM8988 is in ‘playback only’ or ‘record and playback’ mode. The mixers and output drivers can be separately enabled by individual control bits (see Analogue Outputs). Thus it is possible to utilise the analogue mixing and amplification provided by the WM8988, irrespective of whether the DACs are running or not. The WM8988 receives digital input data on the DACDAT pin. The digital filter block processes the data to provide the following functions: Digital volume control Graphic equaliser and Dynamic Bass Boost Sigma-Delta Modulation Two high performance sigma-delta audio DACs convert the digital data into two analogue signals (left and right). These can then be mixed with analogue signals from the LINPUT1/2 and RINPUT1/2 pins, and the mix is fed to the output drivers, LOUT1/ROUT1 and LOUT2/ROUT2. LOUT1/ROUT1: can drive a 16 or 32 stereo headphone or stereo line output. LOUT2/ROUT2: can drive a 16 or 32 stereo headphone or stereo line output DIGITAL DAC VOLUME CONTROL The signal volume from each DAC can be controlled digitall y, in the same way as the ADC volume (see Digital ADC Volume Control). The gain and attenuation range is –127dB to 0dB in 0.5dB steps. The level of attenuation for an eight-bit code X is given by: 0.5 (X-255) dB for 1 X 255; MUTE for X = 0 The LDVU and RDVU control bits control the loading of digital volume control data. When LDVU or RDVU are set to 0, the LDACVOL or RDACVOL control data is loaded into an intermediate register, but the actual gain does not change. Both left and right gain setting s are updated simultaneously when either LDVU or RDVU are set to 1. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R10 (0Ah) Left Channel Digital Volume
8 LDVU 0 Left DAC Volume Update
0 = Store LDACVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LDACVOL, right = intermediate latch) 7:0 LDACVOL [7:0] 11111111 ( 0dB ) Left DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB R11 (0Bh) Right Channel Digital Volume
8 RDVU 0 Right DAC Volume Update
0 = Store RDACVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = RDACVOL) 7:0 RDACVOL [7:0] 11111111 ( 0dB ) Right DAC Digital Volume Control similar to LDACVOL Table 17 Digital Volume Control
28 Rev 4.2 GRAPHIC EQUALISER The WM8988 has a digital graphic equaliser and adaptive bass boost function. This function operates on digital audio data before it is passed to the audio DACs. Bass enhancement can take two different forms: Linear bass control: bass signals are amplified or attenuated by a user programmable gain. This is independent of signal volume, and very high bass gains on loud signals may lead to signal clipping. Adaptive bass boost: The bass volume is amplified by a variable gain. When the bass volume is low, it is boosted more than when the bass volume is high. This method is recommended because it prevents clipping, and usually sounds more pleasant to the human ear. Treble control applies a user programmable gain, without any adaptive boost function. Bass and treble control are completely independent with separately programmable gains and filter characteristics. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R12 (0Ch) Bass Control
7 BB 0 Bass Boost
0 = Linear bass control 1 = Adaptive bass boost
6 BC 0 Bass Filter Characteristic
0 = Low Cutoff (130Hz at 48kHz sampling) 1 = High Cutoff (200Hz at 48kHz sampling) 3:0 BASS [3:0] 1111 (Disabled) Bass Intensity Code BB=0 BB=1 0000 +9dB 15 (max) 0001 +9dB 14 0010 +7.5dB 13 0011 +6dB 12 0100 +4.5dB 11 0101 +3dB 10 0110 +1.5dB 9 0111 0dB 8 1000 -1.5dB 7 1001 -3dB 6 1010 -4.5dB 5 1011 -6dB 4 1100 -6dB 3 1101 -6dB 2 1110 -6dB 1
1111 Bypass (OFF)
R13 (0Dh) Treble Control
6 TC 0 Treble Filter Characteristic
0 = High Cutoff (8kHz at 48kHz sampling) 1 = Low Cutoff (4kHz at 48kHz sampling) 3:0 TRBL [3:0] 1111 (Disabled) Treble Intensity 0000 or 0001 = +9dB 0010 = +7.5dB … (1.5dB steps) 1011 to 1110 = -6dB 1111 = Disable Table 18 Graphic Equaliser
Rev 4.2 29 DIGITAL TO ANALOGUE CONVERTER (DAC) After passing through the graphic equaliser filters, digital ‘de -emphasis’ can be applied to the audio data if necessary (e.g. when the data comes from a CD with pre -emphasis used in the recording). De- emphasis filtering is available for sample rates of 48kHz, 44.1kHz and 32kHz. The WM8988 also has a Soft Mute function, which gra dually attenuates the volume of the digital signal to zero. When removed, the gain will r eturn to the original setting. This function is enabled by default. To play back an audio signal, it must first be disabled by setting the DACMU bit to zero. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R5 (05h) ADC and DAC Control 2:1 DEEMP [1:0]
00 De-emphasis Control
11 = 48kHz sample rate 10 = 44.1kHz sample rate 01 = 32kHz sample rate 00 = No De-emphasis
3 DACMU 1 Digital Soft Mute
1 = mute 0 = no mute (signal active) Table 19 DAC Control The digital audio data is converted to oversampled bit streams in the on -chip, true 24 -bit digital interpolation filters. The bitstream data enters two multi -bit, sigma-delta DACs, which convert them to high quality analogue audio signals. The multi -bit DAC architecture reduces high frequency noise and sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and low distortion. In normal operation, the left and right channel digital audio data is converted to analogue in two separate DACs. However, it is also possible to disable one channel, so that the same signal (left or right) appears on both analogue output channels. Additionally, there is a mono -mix mode wh ere the two audio channels are mixed together digitally and then converted to analogue using only one DAC, while the other DAC is switched off. The mono-mix signal can be selected to appear on both analogue output channels. The DAC output defaults to non -inverted. Setting DACINV will invert the DAC output phase on both left and right channels. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R23 (17h) Additional Control (1) 5:4 DMONOMIX [1:0]
00 DAC mono mix
00: stereo 01: mono ((L+R)/2) into DACL, ‘0’ into DACR 10: mono ((L+R)/2) into DACR, ‘0’ into DACL 11: mono ((L+R)/2) into DACL and DACR
1 DACINV 0 DAC phase invert
0 : non-inverted 1 : inverted Table 20 DAC Mono Mix and Phase Invert Select
30 Rev 4.2 OUTPUT MIXERS The WM8988 provides the option to mix the DAC output signal with analogue line -in signals from the LINPUT1/2, RINPUT1/2 pins or a mono differential input (LINPUT1 – RINPUT1) or (LINPUT2 – RINPUT2), selected by DS (see Table 6) . The level of the mixed -in signals can be controlled with PGAs (Programmable Gain Amplifiers). The mono mixer is designed to allow a number of signal combinations to be mixed, including the possibility of mixing both the right and left channels together to produce a mono output. To prevent overloading of the mixer when full-scale DAC left and right signals are input, the mixer inputs from the DAC outputs each have a fixed gain of -6dB. The bypass path inputs to the mono mixer have variable gain as determined by R38/R39 bits [6:4]. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R34 (22h) Left Mixer (1) 2:0 LMIXSEL 000 Left Input Selection for Output Mix 000 = LINPUT1 001 = LINPUT2 010 = Reserved 011 = Left ADC Input (after PGA / MICBOOST) 100 = Differential input R36 (24h) Right Mixer (1) 2:0 RMIXSEL 000 Right Input Selection for Output Mix 000 = RINPUT1 001 = RINPUT2 010 = Reserved 011 = Right ADC Input (after PGA / MICBOOST) 100 = Differential input Table 21 Output Mixer Signal Selection REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R34 (22h) Left Mixer Control (1)
8 LD2LO 0 Left DAC to Left Mixer
0 = Disable (Mute) 1 = Enable Path
7 LI2LO 0 LMIXSEL Signal to Left Mixer
0 = Disable (Mute) 1 = Enable Path 6:4 LI2LOVOL [2:0] 101 (-9dB) LMIXSEL Signal to Left Mixer Volume 000 = +6dB … (3dB steps) 111 = -15dB R35 (23h) Left Mixer Control (2)
8 RD2LO 0 Right DAC to Left Mixer
0 = Disable (Mute) 1 = Enable Path
7 RI2LO 0 RMIXSEL Signal to Left Mixer
0 = Disable (Mute) 1 = Enable Path 6:4 RI2LOVOL [2:0] 101 (-9dB) RMIXSEL Signal to Left Mixer Volume 000 = +6dB … (3dB steps) 111 = -15dB Table 22 Left Output Mixer Control
Rev 4.2 31 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R36 (24h) Right Mixer Control (1)
8 LD2RO 0 Left DAC to Right Mixer
0 = Disable (Mute) 1 = Enable Path
7 LI2RO 0 LMIXSEL Signal to Right Mixer
0 = Disable (Mute) 1 = Enable Path 6:4 LI2ROVOL [2:0] 101 (-9dB) LMIXSEL Signal to Right Mixer Volume 000 = +6dB … (3dB steps) 111 = -15dB R37 (25h) Right Mixer Control (2)
8 RD2RO 0 Right DAC to Right Mixer
0 = Disable (Mute) 1 = Enable Path
7 RI2RO 0 RMIXSEL Signal to Right Mixer
0 = Disable (Mute) 1 = Enable Path 6:4 RI2ROVOL [2:0] 101 (-9dB) RMIXSEL Signal to Right Mixer Volume 000 = +6dB … (3dB steps) 111 = -15dB Table 23 Right Output Mixer Control
32 Rev 4.2 ANALOGUE OUTPUTS LOUT1/ROUT1 OUTPUTS The LOUT1 and ROUT1 pins can drive a 16 or 32 headphone or a line output (see Headphone Output and Line Output sections, respectively). The signal volu me on LOUT1 and ROUT1 can be independently adjusted under software control by writing to LOUT1VOL and ROUT1VOL, respectively. Note that gains over 0dB may cause clipping if the signal is large. Any gain setting below 0101111 (minimum) mutes the output driv er. The corresponding output pin remains at the same DC level (the reference voltage on the VREF pin), so that no click noise is produced when muting or un-muting. A zero cross detect on the analogue output may also be enabled when changing the gain setti ng to minimize audible clicks and zipper noise as the gain updates. If zero cross is enabled a timeout is also available to update the gain if a zero cross does not occur. This function may be enabled by setting TOEN in register R23 (17h). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R2 (02h) LOUT1 Volume
8 LO1VU 0 Left Volume Update
0 = Store LOUT1VOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LOUT1VOL, right = intermediate latch)
7 LO1ZC 0 Left zero cross enable
1 = Change gain on zero cross only 0 = Change gain immediately 6:0 LOUT1VOL [6:0] 1111001 (0dB) LOUT1 Volume 1111111 = +6dB … (80 steps) 0110000 = -67dB 0111111 to 0000000 = Analogue MUTE R3 (03h) ROUT1 Volume
8 RO1VU 0 Right Volume Update
0 = Store ROUT1VOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = ROUT1VOL)
7 RO1ZC 0 Right zero cross enable
1 = Change gain on zero cross only 0 = Change gain immediately 6:0 ROUT1VOL [6:0]
1111001 ROUT1 Volume
1111111 = +6dB … (80 steps) 0110000 = -67dB 0111111 to 0000000 = Analogue MUTE Table 24 LOUT1/ROUT1 Volume Control
Rev 4.2 33 LOUT1/ROUT1 COMMON GROUND FEEDBACK (HPCOM) The LOUT1/ROUT1 outputs also have the option of incorporating common ground feedback from the output signal ground, via a connection to the HPCOM input. This common ground feedback signal should be AC-coupled via a 4.7uF capacitor for the headphone loads. AC coupling of these outputs if they are used as LINE level outputs requires similar 1 to 4.7uF AC coupling capacitors depending upon LINE load resistance. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R24 (18h) HPCOM Control
7 HPCOMEN 0 Enables common mode feedback on
0: Disable Common Mode Feedback 1: Enable Common Mode Feedback Table 25 HPCOM Control LOUT2/ROUT2 OUTPUTS The LOUT2 and ROUT2 output pins are essentially similar to LOUT1 and ROUT1, but they are independently controlled. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R40 (28h) LOUT2 Volume 6:0 LOUT2VOL [6:0] 1111001 (0dB) LOUT2 Volume 1111111 = +6dB … (80 steps) 0110000 = -67dB 0111111 to 0000000 = Analogue MUTE
7 LO2ZC 0 Left zero cross enable
1 = Change gain on zero cross only 0 = Change gain immediately
8 LO2VU 0 Same as LO1VU
R41 (29h) ROUT2 Volume 6:0 ROUT2VOL [6:0] 1111001 (0dB) ROUT2 Volume 1111111 = +6dB … (80 steps) 0110000 = -67dB 0111111 to 0000000 = Analogue MUTE
7 RO2ZC 0 Right zero cross enable
1 = Change gain on zero cross only 0 = Change gain immediately
8 RO2VU 0 Same as RO1VU
R24 (18h) Additional Control (2)
4 ROUT2INV 0 ROUT2 Invert
0 = No Inversion (0 phase shift) 1 = Signal inverted (180 phase shift) Table 26 LOUT2/ROUT2 Volume Control LOUT2/ROUT2 COMMON GROUND FEEDBACK (LCOM) The LOUT2/ROUT2 outputs also have the option of incorporating common ground feedback from the output signal ground, via a connection to the LCOM input. This common ground feedback signal should be AC-coupled via a 4.7uF capacitor for headphone loads. AC coupling of these outputs if they are used as LINE level outputs requires similar 1 to 4.7uF AC coupling capacitors depending upon LINE load resistance.
34 Rev 4.2 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R24 (18h) LCOM Control
8 LCOMEN 0 Enables common mode feedback on
0: Disable Common Mode Feedback 1: Enable Common Mode Feedback Table 27 LCOM Control ENABLING THE OUTPUTS Each analogue output of the WM8988 can be separately en abled or disabled. The analogue mixer associated with each output is powered on or off along with the output pin. All outputs are disabled by default. To save power, unused outputs should remain disabled. Outputs can be enabled at any time, except when VRE F is disabled (VR=0), as this may cause pop noise (see “Power Management” and “Applications Information” sections) REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R26 (1Ah) Power Management (2)
6 LOUT1 0 LOUT1 Enable
5 ROUT1 0 ROUT1 Enable
4 LOUT2 0 LOUT2 Enable
3 ROUT2 0 ROUT2 Enable
Note: All “Enable” bits are 1 = Enabled, 0 = Disabled Table 28 Analogue Output Control Whenever an analogue output is disabled, it remains connected to VREF (pin 20) through a resistor. This helps to prevent pop noise when the output is re -enabled. The resistance between VREF and each output can be controlled using the VROI bit in register 27. The default is low (1.5k ), so that any capacitors on the outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the resistance to about 40k. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R27 (1Bh) Additional (1)
6 VROI 0 VREF to analogue output resistance
0: 1.5 k 1: 40 k Table 29 Disabled Outputs to VREF Resistance THERMAL SHUTDOWN The headphone outputs can drive very large currents. To protect the WM8988 from overheating a thermal shutdown circuit is included. If the device temperature reaches ap proximately 1500C and the thermal shutdown circuit is enabled (TSDEN = 1) then the headphone amplifiers (outputs OUT1L/R and OUT2L/R) will be disabled. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R23 (17h) Additional Control (1)
8 TSDEN 0 Thermal Shutdown Enable
0 : thermal shutdown disabled 1 : thermal shutdown enabled Table 30 Thermal Shutdown
Rev 4.2 35 DIGITAL AUDIO INTERFACE The digital audio interface is used for inputting DAC data into the WM8988 and outputting ADC data from it. It uses four pins: ADCDAT: ADC data output DACDAT: DAC data input LRC: DAC and ADC data alignment clock BCLK: Bit clock, for synchronisation The clock signals BCLK and LRC can be an output when the WM8988 operates as a master, or an input when it is a slave (see Master and Slave Mode Operation, below). Four different audio data formats are supported: Left justified I2S DSP mode (Mode A) DSP mode (Mode B) All four of these modes are MSB first. They are described in Audio Data Formats, below. Refer to the Electrical Characteristic section for timing information. MASTER AND SLAVE MODE OPERATION The WM8988 can be configured as either a master or slave mode device. As a master device the WM8988 generates BCLK, ADCLRC and DACLRC and thus controls sequencing of th e data transfer on ADCDAT and DACDAT. In slave mode, the WM8988 responds with data to clocks it receives over the digital audio interface. The mode can be selected by writing to the MS bit (see Table 23). Master and slave modes are illustrated below. BCLK ADCDAT DACDAT LRCWM8988 CODEC DSP ENCODER/ DECODER BCLK ADCDAT DACDAT LRCWM8988 CODEC DSP ENCODER/ DECODER Figure 10 Master Mode Figure 11 Slave Mode
36 Rev 4.2 AUDIO DATA FORMATS In Left Justified mode, the MSB is available on the first rising edge of BCLK followin g a LRCLK transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles before each LRCLK transition. LEFT CHANNEL RIGHT CHANNEL LRC BCLK DACDAT/ ADCDAT 1/fs n321 n-2 n-1 LSBMSB n321 n-2 n-1 LSBMSB Input Word Length (WL) Note: Input word length is defined by the WL register. Timing is shown with LRP = 0 Figure 12 Left Justified Audio Interface (assuming n-bit word length) In I2S mode, the MSB is available on the second rising edge of BCLK following a LRCLK transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of one sample and the MSB of the next. LEFT CHANNEL RIGHT CHANNEL LRC BCLK DACDAT/ ADCDAT 1/fs n321 n-2 n-1 LSBMSB n321 n-2 n-1 LSBMSB
1 BCLK1 BCLK
Input Word Length (WL) Note: Input word length is defined by the WL register. Timing is shown with LRP = 0 Figure 13 I2S Justified Audio Interface (assuming n-bit word length) In DSP/PCM mode, the left channel MSB is available on either the 1 st (mode B) or 2nd (mode A) rising edge of BCLK (selectable by LRP) following a rising edge of LRC. Right channel data immediately follows left channel data. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of the right channel data and the next sample. In device master mode, the LRC output will resemble the fram e pulse shown in Figure 14 and Figure 15. In device slave mode, Figure 16 and Figure 17, it is possible to use any length of frame pulse less than 1/fs, providing the falling edge of the frame pulse occurs greater than one BCLK period before the rising edge of the next frame pulse.
Rev 4.2 37 LEFT CHANNEL RIGHT CHANNEL LRC BCLK DACDAT / ADCDAT n321 n-2 n-1 LSBMSB n321 n-2 n-1
1 BCLK
Input Word Length (WL) 1/fs Figure 14 DSP/PCM Mode Audio Interface (mode A, LRP=0, Master) LEFT CHANNEL RIGHT CHANNEL LRC BCLK DACDAT / ADCDAT n321 n-2 n-1 LSBMSB n321 n-2 n-1 Input Word Length (WL) 1/fs Figure 15 DSP/PCM Mode Audio Interface (mode B, LRP=1, Master) LEFT CHANNEL RIGHT CHANNEL LRC BCLK DACDAT / ADCDAT n321 n-2 n-1 LSBMSB n321 n-2 n-1 Input Word Length (WL) 1/fs falling edge can occur anywhere in this area Figure 16 DSP/PCM Mode Audio Interface (mode A, LRP=0, Slave)
Table 31. MS selects audio interface operation in master or slave mode. In Master mode BCLK and Slave mode BCLK and LRC are inputs.
7 BCLKINV 0 BCLK invert bit (for master and slave
6 MS 0 Master / Slave Mode Control
5 LRSWAP 0 Left/Right channel swap
4 LRP 0 right, left and I2S modes – LRCLK
Rev 4.2 39 AUDIO INTERFACE OUTPUT TRISTATE Register bit TRI, register 24(18h) bit[3] can be used to tristate the ADCDAT pin and switch ADCLRC, DACLRC and BCLK to inputs. In Slave mode (MASTER=0) LRC and B CLK are by default configured as inputs and only ADCDAT will be tri-stated, (see Table 32). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R24(18h) Additional Control (2)
3 TRI 0 Tristates ADCDAT and switches ADCLRC,
DACLRC and BCLK to inputs. 0 = ADCDAT is an output, LRC and BCLK are inputs (slave mode) or outputs (master mode) 1 = ADCDAT is tristated, LRC and BCLK are inputs Table 32 Tri-stating the Audio Interface MASTER MODE LRC ENABLE In Master mode the lrclk (LRC) is enabled by default only when the DAC is enabled. If ADC only operation in Master mode is required register bit LRCM must be set in o rder to generate an lrclk. For DAC only operation LRCM may be set to ‘0’. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R24(18h) Additional Control (2)
2 LRCM 0 Selects disable mode for LRC
0 = LRC disabled when DAC (Left and Right) disabled. 1 = LRC disabled only when ADC (Left and Right) and DAC (Left and Right) are disabled. Table 33 LRC Enable BIT CLOCK MODE The default master mode bit clock generator produces a bit clock frequency based on the sample rate and input MCLK frequency as shown in Table 36. When enabled by setting the appropriate BCM[1:0] bits, the bit clock mode (BCM) function overrides the default master mode bit clock generator to produce the bit clock frequency shown in the table below: REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R8 (08h) Clocking and Sample Rate Control 8:7 BCM[1:0] 00 BCLK Frequency 00 = BCM function disabled 01 = MCLK/4 10 = MCLK/8 11 = MCLK/16 Table 34 Master Mode BCLK Frequency Control The BCM mode bit clock generator produces 16 or 24 -bit clock cycles per sample. The number of bit clock cyc les per sample in this mode is determined by the word length bits (WL[1:0]) in the Digital Audio Interface Format register (R7). When these bits are set to 00, there will be 16 -bit clock cycles per sample. When these bits are set to 01, 10 or 11, there wil l be 24 bit clock cycles per sample. Please refer to Figure 18. In order to use BCM either the ADC must be enabled or, if the ADC is disabled, the LRCM bit must be set and the DAC enabled. When the BCM function is enabled, the following restrictions apply: 1. The bit clock invert (BCLKINV) function is not available. 2. DSP late digital audio interface mode is not available and must not be enabled.
40 Rev 4.2 LRC MCLK MCLK/4 MCLK/8 MCLK/16 Figure 18 Bit Clock Mode Note: The shaded bit clock cycles are present only when 24 -bit mode is selected. Please refer to the “Bit Clock Mode” description for details. CLOCKING AND SAMPLE RATES The WM8988 supports a wide range of master clock frequencies on the MCLK pin, and can generate many commonly used audio sample rates directly from the master clock. The ADC and DAC must always run at the same sample rate. There are two clocking modes: ‘Normal’ mode supports master clocks of 128fs, 192fs, 256fs, 384fs, and their multiples (Note: fs refers to the ADC or DAC sample rate, whichever is faster) USB mode supports 12MHz or 24MHz master clocks. This mode is intended for use in systems with a USB interface, and eliminates the need for an external PLL to generate another clock frequency for the audio CODEC. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R8 (08h) Clocking and Sample Rate Control
6 CLKDIV2 0 Master Clock Divide by 2
1 = MCLK is divided by 2 0 = MCLK is not divided 5:1 SR [4:0] 00000 Sample Rate Control
0 USB 0 Clocking Mode Select
1 = USB Mode 0 = ‘Normal’ Mode Table 35 Clocking and Sample Rate Control The clocking of the WM8988 is controlled using the CLKDIV2, USB, and SR control bits. Setting the CLKDIV2 bit divides MCLK by tw o internally. The USB bit selects between ‘Normal’ and USB mode. Each value of SR[4:0] selects one combination of MCLK division ratios and hence one combination of sample rates (see next page). Since all sample rates are generated by dividing MCLK, their a ccuracy depends on the accuracy of MCLK. If MCLK changes, the sample rates change proportionately. target value by a very small amount. This is not audible , as the maximum deviation is only 0.27% (8.0214kHz instead of 8kHz in USB mode). By comparison, a half -tone step corresponds to a 5.9% change in pitch. The SR[4:0] bits must be set to configure the appropriate ADC and DAC sample rates in both master and slave mode.
Rev 4.2 41 MCLK CLKDIV2=0 MCLK CLKDIV2=1 ADC SAMPLE RATE (ADCLRC) DAC SAMPLE RATE (DACLRC) USB SR [4:0] FILTER TYPE BCLK (MS=1) ‘Normal’ Clock Mode (‘*’ indicates backward compatibility with WM8731) 12.288 MHz 24.576 MHz 8 kHz (MCLK/1536) 8 kHz (MCLK/1536) 0 00110 * 1 MCLK/4 12 kHz (MCLK/1024) 12 kHz (MCLK/1024) 0 01000 1 MCLK/4 16 kHz (MCLK/768) 16 kHz (MCLK/768) 0 01010 1 MCLK/4 24 kHz (MCLK/512) 24 kHz (MCLK/512) 0 11100 1 MCLK/4 32 kHz (MCLK/384) 32 kHz (MCLK/384) 0 01100 * 1 MCLK/4 48 kHz (MCLK/256) 48 kHz (MCLK/256) 0 00000 * 1 MCLK/4 96 kHz (MCLK/128) 96 kHz (MCLK/128) 0 01110 * 3 MCLK/2 11.2896MHz 22.5792MHz 8.0182 kHz (MCLK/1408) 8.0182 kHz (MCLK/1408) 0 10110 * 1 MCLK/4 11.025 kHz (MCLK/1024) 11.025 kHz (MCLK/1024) 0 11000 1 MCLK/4 22.05 kHz (MCLK/512) 22.05 kHz (MCLK/512) 0 11010 1 MCLK/4 44.1 kHz (MCLK/256) 44.1 kHz (MCLK/256) 0 10000 * 1 MCLK/4 88.2 kHz (MCLK/128) 88.2 kHz (MCLK/128) 0 11110 * 3 MCLK/2 18.432MHz 36.864MHz 8 kHz (MCLK/2304) 8 kHz (MCLK/2304) 0 00111 * 1 MCLK/6 12 kHz (MCLK/1536) 12 kHz (MCLK/1536) 0 01001 1 MCLK/6 16kHz (MCLK/1152) 16 kHz (MCLK/1152) 0 01011 1 MCLK/6 24kHz (MCLK/768) 24 kHz (MCLK/768) 0 11101 1 MCLK/6 32 kHz (MCLK/576) 32 kHz (MCLK/576) 0 01101 * 1 MCLK/6 48 kHz (MCLK/384) 48 kHz (MCLK/384) 0 00001 * 1 MCLK/6 96 kHz (MCLK/192) 96 kHz (MCLK/192) 0 01111 * 3 MCLK/3 16.9344MHz 33.8688MHz 8.0182 kHz (MCLK/2112) 8.0182 kHz (MCLK/2112) 0 10111 * 1 MCLK/6 11.025 kHz (MCLK/1536) 11.025 kHz (MCLK/1536) 0 11001 1 MCLK/6 22.05 kHz (MCLK/768) 22.05 kHz (MCLK/768) 0 11011 1 MCLK/6 44.1 kHz (MCLK/384) 44.1 kHz (MCLK/384) 0 10001 * 1 MCLK/6 88.2 kHz (MCLK/192) 88.2 kHz (MCLK/192) 0 11111 * 3 MCLK/3 USB Mode (‘*’ indicates backward compatibility with WM8731) 12.000MHz 24.000MHz 8 kHz (MCLK/1500) 8 kHz (MCLK/1500) 1 00110 * 0 MCLK 8.0214 kHz (MCLK/1496) 8.0214kHz (MCLK/1496) 1 10111 * 1 MCLK 11.0259 kHz (MCLK/1088) 11.0259kHz (MCLK/1088) 1 11001 1 MCLK 12 kHz (MCLK/1000) 12 kHz (MCLK/1000) 1 01000 0 MCLK 16kHz (MCLK/750) 16kHz (MCLK/750) 1 01010 0 MCLK 22.0588kHz (MCLK/544) 22.0588kHz (MCLK/544) 1 11011 1 MCLK 24kHz (MCLK/500) 24kHz (MCLK/500) 1 11100 0 MCLK 32 kHz (MCLK/375) 32 kHz (MCLK/375) 1 01100 * 0 MCLK 44.118 kHz (MCLK/272) 44.118 kHz (MCLK/272) 1 10001 * 1 MCLK 48 kHz (MCLK/250) 48 kHz (MCLK/250) 1 00000 * 0 MCLK 88.235kHz (MCLK/136) 88.235kHz (MCLK/136) 1 11111 * 3 MCLK 96 kHz (MCLK/125) 96 kHz (MCLK/125) 1 01110 * 2 MCLK Table 36 Master Clock and Sample Rates
42 Rev 4.2 CONTROL INTERFACE SELECTION OF CONTROL MODE The WM8988 is controlled by writing to registers through a serial control interface. A control word consists of 16 bits. The first 7 bits (B15 to B9) are address bits that select which control register is accessed. The remaining 9 bits (B8 to B0) are data bits, corresponding to the 9 bits in each control register. The control interface can operate as either a 3 -wire or 2-wire MPU interface. The MODE pin selects the interface format. MODE INTERFACE FORMAT Low 2 wire High 3 wire Table 37 Control Interface Mode Selection 3-WIRE SERIAL CONTROL MODE In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on CSB latches in a complete control word consisting of the last 16 bits. B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0SDIN SCLK CSB control register address control register data bits latch Figure 19 3-Wire Serial Control Interface 2-WIRE SERIAL CONTROL MODE The WM8988 supports software control via a 2-wire serial bus. Many devices can be controlled by the same bus, and each device has a unique 7 -bit address (this is not the same as the 7 -bit address of each register in the WM8988). The WM8988 operates as a slave device only. The controller indicates the start of data transfer with a high to low transition on SDIN while SCLK remains high. This indicates that a device address and data will follow. All devices on the 2 -wire bus respond to the start condition and shift in the next eight bits on SDIN (7 -bit address + Read/Write bit, MSB first). If the device address received match es the address of the WM8988 and the R/W bit is ‘0’, indicating a write, then the WM8988 responds by pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is ‘1’, the WM8988 returns to the idle condition and wait for a new start condition and valid address. Once the WM8988 has acknowledged a correct address, the controller sends the first byte of control data (B15 to B8, i.e. the WM8988 register address plus the first bit of register data). The WM8988 then acknowled ges the first data byte by pulling SDIN low for one clock pulse. The controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register data), and the WM8988 acknowledges again by pulling SDIN low. The transfer of data i s complete when there is a low to high transition on SDIN while SCLK is high. After receiving a complete address and data sequence the WM8988 returns to the idle state and waits for another start condition. If a start or stop condition is detected out of s equence at any point during data transfer (i.e. SDIN changes while SCLK is high), the device jumps to the idle condition.
Rev 4.2 43 SDIN SCLK register address and 1st register data bit DEVICE ADDRESS (7 BITS) RD / WR BIT ACK (LOW) CONTROL BYTE 1 (BITS 15 TO 8) CONTROL BYTE 2 (BITS 7 TO 0) remaining 8 bits of register data STOPSTART ACK (LOW) ACK (LOW) Figure 20 2-Wire Serial Control Interface The WM8988 has two possible device addresses, which can be selected using the CSB pin. CSB STATE DEVICE ADDRESS Low 0011010 (0 x 34h) High 0011011 (0 x 36h) Table 38 2-Wire MPU Interface Address Selection
44 Rev 4.2 POWER SUPPLIES The WM8988 can use up to four separate power supplies: AVDD / AGND: Analogue supply, powers all analogue functions except the headphone drivers. AVDD can range from 1.8V to 3.6V and has the most significant impact on overall power consumption (except for power consumed in the headphone). A large AVDD slightly improves audio quality. HPVDD / HPGND: Headphone supply, powers the headphone drivers. HPVDD is normally tied to AVDD, but it requires separate layout and decoupling capacitors to curb harmonic distortion. If HPVDD is lower than AVDD, the output signal may be clipped. DCVDD: Digital core supply, powers all digital functions except the audio and control interfaces. DCVDD can range from 1.42V to 3.6V, and has no effect on audio quality. The return path for DCVDD is DGND, which is shared with DBVDD. DBVDD: Digital buffer supply, powers the audio and control interface buffers. This makes it possible to run the digital core at very low voltages, saving power, while interfacing to other digital devices using a higher voltage. DBVDD draws much less power than DCVDD, and has no effect on audio quality. DBVDD can range from 1.8V to 3.6V. The return path for DBVDD is DGND, which is shared with DCVDD. It is possible to use the same supply voltage on all four. However, digital and analogue supplies should be routed and decoupled separ ately to keep digital switching noise out of the analogue signal paths. POWER MANAGEMENT The WM8988 has two control registers that allow users to select which functions are active. For minimum power consumption, unused functions should be disabled. To avo id any pop or click noise, it is important to enable or disable functions in the correct order (see Applications Information). VMIDSEL is the enable for the Vmid reference, which defaults to disabled and can be enabled as a 50k potential divider or, for l ow power maintenance of Vref when all other blocks are disabled, as a 500k potential divider. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R25 (19h) Power Management (1) 8:7 VMIDSEL 00 Vmid divider enable and select 00 – Vmid disabled (for OFF mode) 01 – 50k divider enabled (for playback/record) 10 – 500k divider enabled (for low-power standby) 11 – 5k divider enabled (for fast start-up)
6 VREF 0 VREF (necessary for all other functions)
0 = Power down 1 = Power up
5 AINL 0 Analogue in PGA Left
0 = Power down 1 = Power up
4 AINR 0 Analogue in PGA Right
0 = Power down 1 = Power up
3 ADCL 0 ADC Left
0 = Power down 1 = Power up
2 ADCR 0 ADC Right
0 = Power down 1 = Power up
Rev 4.2 45 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R26 (1Ah) Power Management (2)
8 DACL 0 DAC Left
0 = Power down 1 = Power up
7 DACR 0 DAC Right
0 = Power down 1 = Power up
6 LOUT1 0 LOUT1 Output Buffer*
0 = Power down 1 = Power up
5 ROUT1 0 ROUT1 Output Buffer*
0 = Power down 1 = Power up
4 LOUT2 0 LOUT2 Output Buffer*
0 = Power down 1 = Power up
3 ROUT2 0 ROUT2 Output Buffer*
0 = Power down 1 = Power up * The left mixer is enabled when LOUT1=1 or LOUT2=1. The right mixer is enabled when ROUT1=1 or ROUT2=1. Table 39 Power Management STOPPING THE MASTER CLOCK In order to minimise power consumed in the digital core of the WM8988, the master clock may be stopped in Standby and OFF modes. If this cannot be done externally at the clock source, the DIGENB bit (R25, bit 0) can be set to stop the MCLK signal from propagating into the devi ce core. In Standby mode, setting DIGENB will typically provide an additional power saving on DCVDD of 20uA . However, since setting DIGENB has no effect on the power consumption of other system components external to the WM8988, it is preferable to disable the master clock at its source wherever possible. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R25 (19h) Additional Control (1)
0 DIGENB 0 Master clock disable
0: master clock enabled 1: master clock disabled Table 40 ADC and DAC Oversampling Rate Selection NOTE: Before DIGENB can be set, the control bits ADCL, ADCR, DACL and DACR must be set to zero and a waiting time of 1ms must be observed. Any failure to follow this procedure may prevent DACs and ADCs from re-starting correctly.
46 Rev 4.2 SAVING POWER BY REDUCING BIAS CURRENTS The design of the DAC allows user trade-off between power consumption and performance, using the DACMIXBIAS bit. The default setting (DACMIXBIAS=0) delivers the best audio performance. Setting DACMIXBIAS=1 reduces AVDD current consumption, at the cost of marginally reduced performance (see “Electrical Characteristics” for details). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R67 (43h) 3 DACMIX BIAS
0 DAC biasing
0 = high bias current (results in higher performance and power consumption) 1 = low bias current (results in lower performance and power consumption) Table 41 DAC Biasing SAVING POWER BY REDUCING OVERSAMPLING RATE The default mode of operation of the ADC and DAC digital filters is in 128x oversampling mode. Under the control of ADCOSR and DACOSR the oversampling rate may be halved. This will result in a slight decrease in noise performance but will also reduce the power consumption of the device. In USB mode ADCOSR must be set to 0, i.e. 128x oversampling. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R24 (18h) Additional Control (2)
1 ADCOSR 0 ADC oversample rate select
1 = 64x (lowest power) 0 = 128x (best SNR)
0 DACOSR 0 DAC oversample rate select
1 = 64x (lowest power) 0 = 128x (best SNR) Table 42 ADC and DAC Oversampling Rate Selection ADCOSR set to ‘1’, 64x oversample mode, is not supported in USB mode (USB=1). SAVING POWER AT HIGHER SUPPLY VOLTAGES The analogue supplies to the WM8988 can run from 1.8V to 3.6V. By default, all analogue circuitry on the device is optimized to run at 3.3V. This set -up is also good for all other supply voltages down to 1.8V. At lower voltages, performance can be improved by increasing the bias current. If low pow er operation is preferred the bias current can be left at the default setting. This is controlled as shown below. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R23 (17h) Additional Control(1) 7:6 VSEL [1:0]
11 Analogue Bias optimization
00: Highest bias current, optimized for AVDD=1.8V 01: Bias current optimized for AVDD=2.5V 1X: Lowest bias current, optimized for AVDD=3.3V
Rev 4.2 47 REGISTER MAP REGISTER ADDRESS (Bit 15 – 9) remarks Bit[8] Bit[7] Bit[6] Bit[5] Bit[4] Bit[3] Bit[2] Bit[1] Bit[0] default page ref R0 (00h) 0000000 Left Input volume LIVU LINMUTE LIZC LINVOL 010010111 20 R1 (01h) 0000001 Right Input volume RIVU RINMUTE RIZC RINVOL 010010111 20 R2 (02h) 0000010 LOUT1 volume LO1VU LO1ZC LOUT1VOL[6:0] 001111001 32 R3 (03h) 0000011 ROUT1 volume RO1VU RO1ZC ROUT1VOL[6:0] 001111001 32 R4 (04h) 0000100 Reserved 0 0 0 0 0 0 0 0 0 000000000 - R5 (05h) 0000101 ADC & DAC Control ADCDIV2 DACDIV2 ADCPOL[1:0] HPOR DACMU DEEMPH[1:0] ADCHPD 000001000 20,26,29 R6 (06h) 0000110 Reserved 0 0 0 0 0 0 0 0 0 000000000 - R7 (07h) 0000111 Audio Interface 0 BCLKINV MS LRSWAP LRP WL[1:0] FORMAT[1:0] 000001010 38 R8 (08h) 0001000 Sample rate BCM[1:0] CLKDIV2 SR[4:0] USB 000000000 40 R9 (09h) 0001001 Reserved 0 0 0 0 0 0 0 0 0 000000000 - R10 (0Ah) 0001010 Left DAC volume LDVU LDACVOL[7:0] 011111111 27 R11 (0Bh) 0001011 Right DAC volume RDVU RDACVOL[7:0] 011111111 27 R12 (0Ch) 0001100 Bass control 0 BB BC 0 0 BASS[3:0] 000001111 28 R13 (0Dh) 0001101 Treble control 0 0 TC 0 0 TRBL[3:0] 000001111 28 R15 (0Fh) 0001111 Reset writing to this register resets all registers to their default state not reset - R16 (10h) 0010000 3D control 0 MODE3D 3DUC 3DLC 3DDEPTH[3:0] 3DEN 000000000 26 R17 (11h) 0010001 ALC1 ALCSEL[1:0] MAXGAIN[2:0] ALCL[3:0] 001111011 24 R18 (12h) 0010010 ALC2 0 ALCZC 0 0 0 HLD[3:0] 000000000 24 R19 (13h) 0010011 ALC3 0 DCY[3:0] ATK[3:0] 000110010 24 R20 (14h) 0010100 Noise Gate 0 NGTH[4:0] NGG[1:0] NGAT 000000000 25 R21 (15h) 0010101 Left ADC volume LAVU LADCVOL[7:0] 011000011 22 R22 (16h) 0010110 Right ADC volume RAVU RADCVOL[7:0] 011000011 22 R23 (17h) 0010111 Additional control(1) TSDEN VSEL[1:0] DMONOMIX[1:0] DATSEL[1:0] DACINV TOEN 011000000 19,20,29,34 R24 (18h) 0011000 Additional control(2) LCOMEN HPCOMEN 0 0 0 TRI LRCM ADCOSR DACOSR 000000000 R25 (19h) 0011001 Pwr Mgmt (1) VMIDSEL[1:0] VREF AINL AINR ADCL ADCR 0 DIGENB 000000000 45 R26 (1Ah) 0011010 Pwr Mgmt (2) DACL DACR LOUT1 ROUT1 LOUT2 ROUT2 0 0 0 000000000 45 R27 (1Bh) 0011011 Additional Control (3) 00 VROI HPFLREN 0 0 0 0 0 000000000 35 R31 (1Fh) 0011111 ADC input mode DS MONOMIX[1:0] RDCM LDCM 0 0 0 0 000000000 18 R32 (20h) 0100000 ADCL signal path 0 LINSEL[1:0] LMICBOOST[1:0] 0 0 0 0 000000000 18 R33 (21h) 0100001 ADCR signal path 0 RINSEL[1:0] RMICBOOST[1:0] 0 0 0 0 000000000 18 R34 (22h) 0100010 Left out Mix (1) LD2LO LI2LO LI2LOVOL[2:0] 0 LMIXSEL[2:0] 001010000 30 R35 (23h) 0100011 Left out Mix (2) RD2LO RI2LO RI2LOVOL[2:0] 0 0 0 0 001010000 30 R36 (24h) 0100100 Right out Mix (1) LD2RO LI2RO LI2ROVOL[2:0] 0 RMIXSEL[2:0] 001010000 31 R37 (25h) 0100101 Right out Mix (2) RD2RO RI2RO RI2ROVOL[2:0] 0 0 0 0 001010000 31 R38 (26h) 0100110 Reserved 0 0 1 0 1 0 0 0 0 001010000 30 R39 (27h) 0100111 Reserved 0 0 1 0 1 0 0 0 0 001010000 30 R40 (28h) 0101000 LOUT2 volume LO2VU LO2ZC LOUT2VOL[6:0] 001111001 33 R41 (29h) 0101001 ROUT2 volume RO2VU RO2ZC ROUT2VOL[6:0] 001111001 33 R42 (2Ah) 0101010 Reserved 0 0 1 1 1 1 0 0 1 001111001 35 R67 (43h) 1000011 Low Power Playback 0 0 0 0 0 DACMIX BIAS 0 0 0 000000000 Highlighting indicates bits or registers which differ from WM8750L / WM8750BL device family.
48 Rev 4.2 DIGITAL FILTER CHARACTERISTICS The ADC and DAC employ different digital filters. There are 4 types of digital filter, called Type 0, 1, 2 and 3. The performance of Types 0 and 1 is listed in the table below, the responses of all filters is shown in the proceeding pages. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ADC Filter Type 0 (USB Mode, 250fs operation) Passband +/- 0.05dB 0 0.416fs -6dB 0.5fs Passband Ripple +/- 0.05 dB Stopband 0.584fs Stopband Attenuation f > 0.584fs -60 dB ADC Filter Type 1 (USB mode, 272fs or Normal mode operation) Passband +/- 0.05dB 0 0.4535fs -6dB 0.5fs Passband Ripple +/- 0.05 dB Stopband 0.5465fs Stopband Attenuation f > 0.5465fs -60 dB High Pass Filter Corner Frequency -3dB 3.7 Hz -0.5dB 10.4 -0.1dB 21.6 DAC Filter Type 0 (USB mode, 250fs operation) Passband +/- 0.03dB 0 0.416fs -6dB 0.5fs Passband Ripple +/-0.03 dB Stopband 0.584fs Stopband Attenuation f > 0.584fs -50 dB DAC Filter Type 1 (USB mode, 272fs or Normal mode operation) Passband +/- 0.03dB 0 0.4535fs -6dB 0.5fs Passband Ripple +/- 0.03 dB Stopband 0.5465fs Stopband Attenuation f > 0.5465fs -50 dB Table 43 Digital Filter Characteristics DAC FILTERS ADC FILTERS Mode Group Delay Mode Group Delay 0 (250 USB) 11/fs 0 (250 USB) 13/fs 1 (256/272) 16/fs 1 (256/272) 23/fs 2 (250 USB, 96k mode) 4/fs 2 (250 USB, 96k mode) 4/fs 3 (256/272, 88.2/96k mode) 3/fs 3 (256/272, 88.2/96k mode) 5/fs Table 44 ADC/DAC Digital Filters Group Delay TERMINOLOGY 1. Stop Band Attenuation (dB) – the degree to which the frequency spectrum is attenuated (outside audio band) 2. Pass-band Ripple – any variation of the frequency response in the pass-band region
Rev 4.2 53 APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS DBVDD DCVDD AVDD LINPUT1 RINPUT1 MODE CSB SDIN SCLK LINPUT2 RINPUT2 BCLK LRC DACDAT ADCDAT AUDIO INTERFACE (I2S/LJ/RJ/DSP) DGND AGND LOUT2 ROUT2 VREF VMID WM8988 C19 C17 C10 C22 C23 HPVDD HPGND C4C3C2C1 DVDD AVDD MCLK CONTROL INTERFACE (2 OR 3-WIRE) HIGH for 3-wire LOW for 2-wire Lineout 4.7uF 1uF 1uF 1uF 1uF 4.7uF 4.7uF 10uF 4.7uF Layout Notes: LOUT1 ROUT1 C14 C15 HEADPHONES220uF 220uF
16 OR 32 OHM
4.7uF C20 4.7uF 10uF HPCOM LCOM GND GND GND GND GND GND GNDGND 1. C1 to C4, C17, C19, C20 and C21 should be as close to the relative WM8988 connecting pin as possible. 2. For capacitors C7 to C10, C14, C15, C22 and C23 it is recommended that low ESR components are used. 3. HPCOM and LCOM should be connected to GND at the connector. 0.1uF 0.1uF Figure 44 Recommended External Components Diagram
Rev 4.2 55 MINIMISING POP NOISE AT THE ANALOGUE OUTPUTS To minimize any pop or click noise when the system is powered up or down, the following procedures are recommended. POWER UP Switch on power supplies. By default the WM8988 is in Standby Mode, the DAC is digitally muted and the Audio Interface, Line outputs and Headphone outputs are all OFF (DACMU = 1 Power Management registers 1 and 2 are all zeros). Enable Vmid and VREF. Enable DACs as required Enable line and / or headphone output buffers as required. Set DACMU = 0 to soft-un-mute the audio DACs. POWER DOWN Set DACMU = 1 to soft-mute the audio DACs. Disable all output buffers. Switch off the power supplies. POWER MANAGEMENT EXAMPLES OPERATION MODE POWER MANAGEMENT (1) POWER MANAGEMENT (2) VREF AINL/R PGAs ADCs DACs Output Buffers PGL PGR ADL ADR MBI DAL DAR LO1 RO1 LO2 RO2 Stereo Headphone Playback 1 0 0 0 0 0 0 1 1 1 1 0 0 Stereo Line-in Record 1 1 1 1 1 1 0 0 0 0 0 0 0 Stereo Microphone Record 1 1 1 1 1 1 1 0 0 0 0 0 0 Mono Microphone Record 1 1 1 0 1 0 1 0 0 0 0 0 0 Stereo Line-in to Headphone Out 1 1 0 0 0 0 0 0 0 1 1 0 0 Table 45 Register Settings for Power Management
56 Rev 4.2 PACKAGE DIMENSIONS DM050.DFL: 28 PIN COL QFN PLASTIC PACKAGE 4 X 4 X 0.55 mm BODY, 0.45 mm LEAD PITCH INDEX AREA (D/2 X E/2) TOP VIEW D E NOTES: 1. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP. 2. ALL DIMENSIONS ARE IN MILLIMETRES. 3. COPLANARITY APPLIES TO THE TERMINALS. 4. REFER TO APPLICATIONS NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING. 5. DEPENDING ON THE METHOD OF LEAD TERMINATION AT THE EDGE OF THE PACKAGE, PULL BACK (L1) MAY BE PRESENT. 6. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. DETAIL 1 A 2822 e 8 1 BCbbb M A BOTTOM VIEW Caaa2 X Caaa2 X C SEATING PLANE DETAIL 2 C0.08 Cccc A SIDE VIEW L DETAIL 1 e Datum DETAIL 2 Terminal Tip e/2 R SEE DETAIL 2 b G T H W Exposed lead DETAIL 2 Dimensions (mm)Symbols MIN NOM MAX NOTE A 0.500 0.550 0.600 0.0500.0350
0.152 REF
b D E e L 0.2800.180 4.000
0.450 BSC
0.400 REF
4.000 0.100 aaa bbb ccc REF: 0.100 0.100 JEDEC, MO-220 Tolerances of Form and Position 0.230 H 0.075 REF
0.200 REFG
T 0.077 REF W 0.150 REF L1 0.000 REF 5 3.950 4.050 3.950 4.050 PIN 1 IDENTIFICATION 0.150MM SQUARE 0.275MM 0.275MM b
Rev 4.2 57 IMPORTANT NOTICE Contacting Cirrus Logic Support For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find one nearest you, go to www.cirrus.com. For the purposes of our terms and conditions of sale, "Preliminary" or "Advanced" datasheets are non-final datasheets that include but are not limited to datasheets marked as “Target”, “Advance”, “Product Preview”, “Preliminary Technical Data” and/or “Pre- production.” Products provided with any such datasheet are therefore subject to relevant terms and conditions associated with "Preliminary" or "Advanced" designations. The products and services of Cirrus Logic International (UK) Limited; Cirrus Logic, Inc.; and other companies in the Cirrus Logic group (collectively either “Cirrus Logic” or “Cirrus”) are sold subject to Cirrus Logic’s terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. Software is provided pursuant to applicable license terms. Cirrus Logic reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Cirrus Logic to verify that the information is current and complete. Testing and other quality control techniques are utilized to the extent Cirrus Logic deems necessary. Specific testing of all parameters of each device is not necessarily performed. In order to minimize risks associated with customer applications, the customer must use adequate design and operating safeguards to minimize inherent or procedural hazards. Cirrus Logic is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Cirrus Logic products. Use of Cirrus Logic products may entail a choice between many different modes of operation, some or all of which may require action by the user, and some or all of which may be optional. Nothing in these materials should be interpreted as instructions or suggestions to choose one mode over another. Likewise, description of a single mode should not be interpreted as a suggestion that other modes should not be used or that they would not be suitable for operation. Features and operations described herein are for illustrative purposes only. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS LOGIC PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, NUCLEAR SYSTEMS, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS LOGIC PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS LOGIC DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS LOGIC PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS LOGIC PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS LOGIC, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. This document is the property of Cirrus Logic and by furnishing this information, Cirrus Logic grants no license, express or implied, under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Any provision or publication of any third party’s products or services does not constitute Cirrus Logic’s approval, license, warranty or endorsement thereof. Cirrus Logic gives consent for copies to be made of the information contained herein only for use within your organization with respect to Cirrus Logic integrated circuits or other products of Cirrus Logic, and only if the reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices and conditions (including this notice). This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. This document and its information is provided “AS IS” without warranty of any kind (express or implied). All statutory warranties and conditions are excluded to the fullest extent possible. No responsibility is assumed by Cirrus Logic for the use of information herein, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. Cirrus Logic, Cirrus, the Cirrus Logic logo design, and SoundClear are among the trademarks of Cirrus Logic. Other brand and product names may be trademarks or service marks of their respective owners. Copyright © 2008–2016 Cirrus Logic, Inc. All rights reserved.
58 Rev 4.2
REVISION HISTORY
DATE RELEASE DESCRIPTION OF CHANGES PAGES 01/05/08 3.0 WM8988 datasheet created 26/09/08 4.0 Product Status updated to Production Data all 18/10/13 4.1 Package Diagram updated: Reference removed to exposed heat sink slug 55 20/12/16 4.2 Package Drawing updated (POD 050.D) 56