WM8738 CIRRUS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 15

Technical content

w WM8738 EV1M WM8738 Evaluation Board User Handbook WOLFSON MICROELECTRONICS LTD www.wolfsonmicro.com August 2002, Rev 2.1 Copyright  2002 Wolfson Microelectronics Ltd. INTRODUCTION The WM8738 is a 24-bit Stereo ADC. This evaluation platform and documentation should be used in conjunction with the latest version of the WM8738 datasheet. The datasheet gives device functionality information as well as timing and data format requirements. This evaluation platform has been designed to allow the user ease of use and give optimum performance in device measurement. GETTING STARTED PACKING LIST The WM8738 Evaluation Kit Contains:

  • 1 WM8738-EV1B Evaluation Board
  • This manual -1 WM8738-EV1M CUSTOMER REQUIREMENTS Minimum Customer Requires:
  • D.C. Power supply of +5V
  • D.C. Power supply of +3.0V to +5.5V
  • D.C. Power supply of +3.0V to +3.6V
  • D.C. Power supply of +12V and -12V ADC Signal Path Requires (minimum):
  • Analogue coaxial jack plug data source
  • Digital coaxial data receiving unit
  • Master Clock source

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 POWER SUPPLIES Using appropriate power leads with 4mm connectors, +5V should be applied to the +5V panel socket J1. +3.0V to +3.6V should be applied to the DVDD panel socket J3 and +3.0V to +5.5V should be applied to the AVDD panel socket J5. +12V should be applied to the +12V panel socket J7 and -12V should be applied to the -12V panel socket J10. DGND should be connected to the DGND panel socket J2 and AGND to the AGND panel socket J6. The DGND and AGND connections may be connected to a common GND on the supply with no reduction in performance. Note: Refer to WM8738 datasheet for limitations on individual supply voltages. BOARD FUNCTIONALITY There are three options for inputting the required digital clocks to the WM8738 evaluation board. There is a coaxial input (J14) via a standard phono connector or a direct digital input is available via one side of a 2x6 pin header (H1). A further option is to input a MCLK via connector J9 and use the CPLD (U1) to generate BCLK and LRCLK. The analogue input signals are applied to the evaluation board via phono connectors through either passive or active anti-alias filters. For passive filtering J17 (LIN) and J16 (RIN) can be used and for active filtering J12 (LIN) and J13 (RIN). There are two options for outputting digital data from the WM8738 evaluation board. There is a coaxial output (J8) via a standard phono connector or the digital signals output from the WM8738 may be accessed via one side of a 2x6 pin header (H2). All WM8738 device pins are accessible for easy measurement via the 8 pin headers (J11 & J15) running up each side of the device. BOARD INPUT Analogue input to the WM8738 is selectable via switches SW5 and SW6. This allows the analogue input to either pass through a passive anti-aliasing filter, using J17 (LIN) and JI6 (RIN), or an active anti-aliasing filter, using J12 (LIN) and J13 (RIN). Digital clock signals must be supplied to the WM8738. A digital (AES/EBU, UEC958, S/PDIF, EIAJ CP340/1201) signal input may be applied to the coaxial input (J14), allowing the CS8427 (U3) to generate the necessary clocks. A direct digital input is also available via one side of a 2x6 pin header (H1). There is also the facility to generate multi-rate clocks from U1 using SW7 as the rate selection and either the MCLK from the CS8427 (U3) or an independent MCLK input to SMB connector J9. The digital inputs of the WM8738 are +5V tolerant (independent of supplies), however, a level shift IC (U2) has been included in the audio interface signal path to buffer the input signals when applied via header (H1) and minimise any performance degradation this may cause.. Note: The level shift IC's (U2 and U6) are set to shift from +5V to DVDD when shipped from Wolfson. BOARD OUTPUT The output interface from the board is via a coaxial (J8) digital (AES/EBU, UEC 958, S/PDIF, EIAJ CP340/1201) signal output. A direct signal output is available via one side of a 2x6 pin header (H2). Data is output in one of the WM8738 supported formats - see datasheet. A level shift IC (U6) has been included in the audio output interface path to provide signal buffering when output signals are taken from 2x6 pin header H2 will meet external receiver requirements.

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 INTERFACES KEY SW1 SW2 J11 J15 J5J1 J2 J3 J10 SW6 SW5 SW41 SW3 SW9 SW8 123456 OPEN ON 1234 SW7 Figure 1 Interfaces HEADERS H1 SIGNAL J15 WM8738 SIGNAL 1/2 MCLK 1 1 DVDD 3/4 GND 2 2 SDOUT 5/6 SLAVE_LRC 3 3 BCLK 7/8 GND 4 4 FMT 9/10 SLAVE_BCLK 5 5 CAP 11/12 GND 6 6 VREF 7 7 RIN H 2 SIGNAL 8 10 AGND 12/11 GND 10/9 SDOUT J11 WM8738 SIGNAL 8/7 GND 1 8 LIN 6/5 BCLK_OUT 2 9 AVDD 4/3 GND 3 10 AGND 2/1 ADC_LRCLK 4 11 NOHP 5 12 LRCLK 6 13 MCLK 7 14 DGND 8 14 DGND Table 1 Headers

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 LINKS LINKS & JUMPERS DESCRIPTION SW3 (FMT) Pins 1 & 2 SHORT – Left Justified mode Pins 2 & 3 SHORT – I2S mode SW4 (NOHP) Pins 1 & 2 SHORT – Digital HPF Disabled Pins 2 & 3 SHORT – Digital HPF Enabled SW5 Pins 1 & 2 SHORT – Active anti-alias filter input selected Pins 2 & 3 SHORT – RC filter only selected SW6 Pins 1 & 2 SHORT – Active anti-alias filter input selected Pins 2 & 3 SHORT – RC filter only selected SW8 Pins 1 & 2 SHORT – Standard CS8427 BCLK selected Pins 2 & 3 SHORT – Multi-rate BCLK selected SW9 Pins 1 & 2 SHORT – Standard CS8427 LRCLK selected Pins 2 & 3 SHORT – Multi-rate LRCLK selected J9 External multi-rate MCLK input Table 2 Links SWITCHES SWITCH DESCRIPTION SW1 (DATA FORMAT) 5 4 3 2 1 DATA FORMAT 0 0 1 0 0 1 I2S Compatible 0 0 0 0 0 1 Left Justified SW2 The CS8427 may be R ESET by pressing and releasing switch SW2. This is required if the switches on SW1 are changed after the board is powered up. SW7 (MCLK RATE) 4 3 2 1 MCLK RATE 1 0 0 0 256fs 0 1 0 0 384fs 0 0 1 0 512fs 0 0 0 1 768fs Table 3 Switches

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 Figure 10 Power

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 WM8738-EV1B BILL OF MATERIAL Description REF-DES QTY 10uF 6.3 Dia 2.5 pitch Oscon Through Hole Cap. 16V 20% C4 C6-7 C9 C13 C17 C51 C55-56 9 1uF 4 Dia 2 pitch Oscon Through Hole Cap. 25V 20% C22 C48 2 0.01uF 0805 SMD Ceramic Capacitor 50V X7R C50 1 0.1uF 0805 SMD Ceramic Capacitor 50V X7R C1-3 C5 C8 C10-12 C14 C16 C18-20 C23 C27 C32-38 C40 C43-44 180pF 0805 SMD Ceramic Capacitor 50V NPO C29 C41 2 1nF 0805 SMD Ceramic Capacitor 50V NPO C24 C39 2 220pF 0805 SMD Ceramic Capacitor 50V X7R C31 C47 C58 C59 4 820pF 0805 SMD Ceramic Capacitor 50V NPO C30 C46 2 82nF 0805 SMD Ceramic Capacitor 25V X7R C49 1 1uF 1206 SMD Ceramic Capacitor 16V X7R C25 C52 C53 C61 4 2.2nF 1206 SMD Ceramic Capacitor 50V NPO C42 1 4.7nF 1206 SMD Ceramic Capacitor 50V COG C21 C26 C54 C62 4 2x5 2.54mm Male PCB Header LoPro VERTICAL J4 1 1x8 2.54mm pitch PCB Pin Header VERTICAL J11 J15 2 2x6 2.54mm pitch PCB Pin Header VERTICAL H1-2 2 JSK9-16-G0 PCB 1x3 Jumper Switch 0.1" Center-off VERTICAL SW3-6 SW8-9 6 4mm Non-Insulated Panel Socket 16A J1-3 J5-7 J10 7 Phono Socket PCB mount BLACK J8 1 Phono Socket PCB mount RED J13 J16 2 Phono Socket PCB mount WHITE J12 J17 2 Phono Socket PCB mount YELLOW J14 1 SMB Connector PCB Mount 50 Ohm VERTICAL J9 1 CD8427 96KHz Audio Transceiver U3 1 DS1813 5V active Low Power-On-Reset chip SOT U7 1 0R 1206 Resistor on 1210 Inductor site L1-4 L6 5 3.3uH 1210 Surface Mount Inductor '1210A series' L7 1 MC33078 Low Noise Dual Op-Amp SO U5 1 0R 0805 SMD chip resistor 1% 0.1W R2 R4 R5 R7 R12 R16 R42 7 100K 0805 SMD chip resistor 1% 0.1W R20 R29 R39 3 10K 0805 SMD chip resistor 1% 0.1W R1 R3 R6 R8 R21 5 47K 0805 SMD chip resistor 1% 0.1W R13 R15 R17 R19 R23-24 R26 R30-33 R35 12 5k1 0805 SMD chip resistor 1% 0.125W R34 1 620R 0805 SMD chip resistor 1% 0.1W R11 1 680R 0805 SMD chip resistor 1% 0.1W R22 R41 R45 R48 4 75R 0805 SMD chip resistor 1% 0.125W R40 1 8K2 0805 SMD chip resistor 1% 0.1W R25 R27-28 R36-38 6 SN74LVCC4245A Octal Dual Supply(5V, 3-5V) Transceiver SO U2 U6 2 DIL Switch 4-Way Rocker SW7 1 DIL Switch 6-Way Rocker SW1 1 B3F1000 SPNO PCB mount switch SW2 1 1.32mm PCB Test Terminal BLACK TP1-6 6 2:1 Ratio 96KHz SPDIF Digital Audio transformer SOIC T1 1 WM8738 Stereo ADC U4 1 XC9536XL-15 3.3V 36 macrocell CPLD U1 1 Note: 1 The audio transformer (T1) used on this board is manufactured by Scientific Conversion Inc. (www.scientificonversion.com).

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 EVALUATION SUPPORT The aim of this evaluation kit is to help you to become familiar with the functionality and performance of the WM8738, stereo audio ADC. If you require more information or require technical support please contact Wolfson Microelectronics Applications group through the following channels: Email: apps@wolfsonmicro.com Apps. Telephone: (+44) 131 272 7070 Fax: (+44) 131 272 7001 Mail: Applications at the address on the last page. or contact your local Wolfson representative. Additional information may be made available from time to time on our web site at: http://www.wolfsonmicro.com

WOLFSON MICROELECTONICS LTD Rev 2.1 August 2002 IMPORTANT NOTICE Wolfson Microelectronics Ltd (WM) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current. All products are sold subject to the WM terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. WM warrants performance of its products to the specifications applicable at the time of sale in accordance with WM’s standard warranty. Testing and other quality control techniques are utilised to the extent WM deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. In order to minimise risks associated with customer applications, adequate design and operating safeguards must be used by the customer to minimise inherent or procedural hazards. WM assumes no liability for applications assistance or customer product design. WM does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of WM covering or relating to any combination, machine, or process in which such products or services might be or are used. WM’s publication of information regarding any third party’s products or services does not constitute WM’s approval, license, warranty or endorsement thereof. Reproduction of information from the WM web site or datasheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated WM product or service is an unfair and deceptive business practice, and WM is neither responsible nor liable for any such use. Resale of WM’s products or services with statements different from or beyond the parameters stated by WM for that product or service voids all express and any implied warranties for the associated WM product or service, is an unfair and deceptive business practice, and WM is neither responsible nor liable for any such use. ADDRESS: Wolfson Microelectronics Ltd

20 Bernard Terrace

Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: apps@wolfsonmicro.com