WAQ7F101-RA-10

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Proprietary and Confidential Property of Superworld (a) (c)(b) (e)(d) 1. PART NO. EXPRESSION : (b) Dimension code (c) Material code (a) Series code 2. CONFIGURATION & DIMENSIONS : 4. MATERIALS : SUPERWORLD ELECTRONICS (S) PTE LTD 3. SCHEMATIC : (e) R : Tape & Reel (f) Rated Current : B = 200mA PG. 1 PCB Pattern B C D1 D2 L H K1 K2 WAQ 7 F 5 1 0 - R B - 1 0 A B L H 4.5± 0.2 A (f) (g) (d) Inductance code : 510 = 51 uH (g) 10 : Internal Control Number (b) Core:Ferrite Core d (c) Termination : Tin (Pb Free) (d) Wire : Enameled Copper Wirec b (a) Upper Plate:Ferritea PC board should be designed so that products are not sufficient Products shall be positioned in the sideway direction against the mechanical stress to prevent failure. under mechanical stress as warping the board. Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY C K1G2 Unit:m/m 0.9 01.04.2015 NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES

01 APR 2015

SUPERWORLD ELECTRONICS (S) PTE LTD 6. ELECTRICAL CHARACTERISTICS : a) Test Frequency ：Inductance:100KHz/0.1V; Impedance:10MHz/0.1V PG. 2 5. GENERAL SPECIFICATION : ( Ω ) WAQ7F510-RB-10 Part No. ( Ω ) Max. 51+50/-30% ( uH ) Inductance Common mode 1.0 DCR ( Vdc ) Voltage Rated 200 ( mA ) Current Rated 10M IR Min. 7. CHARACTERISTICS CURVES : Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY Proprietary and Confidential Property of Superworld c) Storage Temperature:-40 ~ +125℃℃ b) Operating temperature: -40 ~ +125℃℃ d) All test data is referenced to 25 ambient.℃ 1 10 100 1000 FREQUENCY(MHz) 100 1000 10000 10000 0 IMPEDANCE(Ohm) Common Mode Normal Mode e) Indicate Compliant to AEC-Q200 and PPAP level4 eligibility WAQ7F510-RB-10 WAQ7F101-RA-10 100+50/-30% 2.0 50 100 10M WAQ7F110-RB-10 11+50/-30% 0.8 50 200 10M WAQ7F110-RB-10 WAQ7F101-RA-10 NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES 11 0 1 0 0 1 0 0 0 FRE QUE NCY( MHz ) 100 1000 10000IMPEDANCE( Ohm) ACM 45 32F2S F -110 Common Mode Norma l M ode 11 0 1 0 0 1 0 0 0 FRE QUENCY(MHz) 100 1000 10000 10000 0 IM PED AN CE(Ohm ) Commo n M od e N o rm al Mo de 01.04.2015

Proprietary and Confidential Property of Superworld 8. RELIABILITY & TEST CONDITION : Terminal Strength Solder Heat Resistance Solderability Test Mechanical Performance Test Temperature Rise Test Z (common mode) Electrical Characteristics Test ITEM I.R. DCR TEST CONDITIONPERFORMANCE Agilent4339 2. Temperature measured by digital surface thermometer. Refer to standard electrical characteristics list More than 90% of termincal electr ode should be covered with solder. Rated Current < 1A ΔT 20°CMax 1. Applied the allowed DC current. Agilent-4291A+ Agilent - 16197A Agilent-4338B Rated Current 1A ΔT 40°CMax≧ RDC ：within ±15% of initial value and shall not Appearance ：No damage. Inductance ：within±10% of initial value exceed the specification value Solder tamperature: 260± 5° C Temperature ramp/immersion and immersion Dip time: 10± 1sec. Depth: completely cover the termination. rate: 25± 6 mm/s ( IPC/JEDEC J-STD-020D Classification Reflow Profiles) With the component mounted on a PCB with the device to be tested, apply a force (>0805:1kg , <= 0805:0.5kg)to Preconditioning : Run through IR reflow for 2 times. the side of a device being tested. This force shall be applied for 60 +1 seconds. Also the force shall be applied gradually as not to apply a shock to the com ponent being tested. SUPERWORLD ELECTRONICS (S) PTE LTD Flux for lead free: Rosin. 9.5%。 Dip time: 4±1sec。 Depth: completely cover t he t erminat ion Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY Preheat: 150 ℃,60sec.。 Solder: Sn99.5%-Cu0. 5%。 Temperature: 245±5℃。 Number of heat cycles:1 NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 3 WAQ7F SERIES 01.04.2015

Proprietary and Confidential Property of Superworld PG. 4 Humidity Resistance Test Thermal Shock Life Test Reliabilty Test ITEM Humidity : 85± 2% R.H Measured at room temperature after placing for 24± 2 hrs Duration ：1000hrs Min. with 100% rated current Number of cycles ： 500 Temperature : 85± 2° C Measured at room fempraturc after placing for 24± 2 hrs Step 30± 5-40± 2 25± 2 105± 2 0.5≦ 30± 5 Temperature (° C) Times (min.) PERFORMANCE TEST CONDITION Testing Time : 12 hours(20 minutes, 12 cycles each of 3 orientations)。 Total Amplitude : 1.52mm± 10% Oscillation Fr equency : 10 ～2K～10Hz for 20 minutes Vibration Test Equipment : Vibration checker 8. RELIABILITY & TEST CONDITION : Duration : 1000± 12hrs Applied Current : rated current Temperature : 85± 2° C Measured at room temperature after placing for 24± 2 hrs. ( IPC/JEDEC J-STD-020D Classification Reflow Profiles) Preconditioning: Run through IR reflow for 2 times. ( IPC/JEDEC J-STD-020D Classification Reflow Profiles) Preconditioning: Run through IR reflow for 2 times. ( IPC/JEDEC J-STD-020D Classification Reflow Profiles) Preconditioning: Run through IR reflow for 2 times. ( IPC/JEDEC J-STD-020D Classification Reflow Profiles) Preconditioning: Run through IR reflow for 2 times. SUPERWORLD ELECTRONICS (S) PTE LTD Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY RDC ：within ±15% of initial value and shall not Appearance ：No damage. Inductance ：within±10% of initial value exceed the specification value NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES 01.04.2015

Proprietary and Confidential Property of Superworld b) 355° C tip temperature (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 4-5 secs. d) 1.0mm tip diameter (max) c) Never contact the ceramic with the iron tip If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Mildly activated rosin fluxes are preferred. Our terminations are suitable for all wave and re-flow soldering systems. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. 9-1.1 Solder Re-flow : a) Preheat circuit and products to 150° C. 9-1.2 Soldering Iron (Figure 2) : Note : 9. SOLDERING AND MOUNTING : 9-1. Soldering Soldering TP(260 °C/10s max) 60~150s Time(sec.) Reflow times: 3 times max. TEMPERATURE ° C 150 60~180s 480s max. TP(245° C/20~40s) 200 217 Preheating Over 60s. Gradual Cooling Within 4-5s Iron Soldering times: 1 times max. TEMPERATURE ° C cooling Natural cooling 350 150 SolderingPreheating Natural Fig.2 Fig.1 Time(sec.) SUPERWORLD ELECTRONICS (S) PTE LTD Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPYPG. 5 NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES 01.04.2015

Proprietary and Confidential Property of Superworld SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6 Ko(mm) 3.00± 0.1 Bo(mm) 4.90± 0.1 Ao(mm) 3.60± 0.1 P(mm) 8.0± 0.1 t(mm) 0.26± 0.05 D(mm) 178.0± 2.0 10-2 Tape Dimension / 12mm 7" x 8mm D C B R0.5R1.9 120¢ X 7" x 12mm 2± 0.5 60.0± 2.0 R10.5 13.5± 0.5 7" x 12mm 13.5± 0.5 13.5± 0.5 Type A(mm) C(mm) B( mm) 10-1. Reel Dimension 10. PACKAGING INFORMATION : A 10-3. Packing Quantity Carton Middle Box Chip / Reel Seri e s Inner Box 25000 12500 500 2500 WAQ7F Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY P 5.5± 0.05 D1:1.5± 0.1 1.75± 0.1 Po:4± 0.1D:1.5+0.1 Bo W:12.0± 0.1 KoAo P2:2± 0.05 t Section A- A A A Seri e s WAQ7F NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES 01.04.2015

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 7 10-4. Tearing Off Force Base tape a) Temperature and humidity conditions : Less than 40° C and 60% RH. b) Recommended products should be used within 12 months from the time of delivery. c) The packaging material should be kept where no chlorine or sulfur exists in the air. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. To maintain the solderabililty of terminal electrodes : 1. Storage Conditions : Application Notice 2. Transportation : Top cover tape 165° to 180° F Tearing Speed in the arrow direction under the following conditions. The force for tearing off cover tape is 15 to 80 grams 45~855~35 860~1060 Room Humidity (° C) Room Temp. (%) (hPa) Room atm 300 (mm/min) Wirewound Type Common Mode Filter (RoHS Compliant) APPROVED ENGINEERING CONTROLLED COPY Proprietary and Confidential Property of Superworld NOTE : Specifications subject to change without notice. Please check our website for latest information. WAQ7F SERIES 01.04.2015