PIA1707SP100MN

PIA1707SP1R0MN SUPERWORLD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 1. Part No. Expression: P I A 1 7 0 7 S P 1 R 0 M N a) Series Code e) Tolerance Code (a) (b) (c) (d) ( e ) ( f ) b) Dimension Code f) Internal Control Code c) Type Code d) Inductance Code 2. Configuration & Dimensions: 3. Schematic: 4. Material List: A A’ B C D E G H L Note: 1. The above PCB layout is for reference only. 2. Solder paste thickness of 0.17mm and above is recommended. 3. Marking: Top row – Inductance code, Bottom row – YYWW L G H Recommend PC Board Pattern Unit: mm a) Core b) Wire c) Terminal d) Ink Marking D/C

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 5. General Specification: (a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise) (b) Storage Temp. : -40°C to +125°C (on board) (c) Humidity Range : 85 ± 2% RH (d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C (keep 1min) (e) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%. (f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions. (g) Storage condition (component in its packaging) i) Temperature: -10 to 40°C ii) Humidity : 50~60% RH 6. Electrical Characteristics: Notes: 1) At all times, the current supplied to the product should not exceed Isat Max. value. Part Number Inductance Lo (uH) @ 0A ±20% Test Frequency, L Heat Rating Current DC ( A ) Irms. Saturation Current DC (A) Isat. DCR (mΩ)Typ. DCR (mΩ)Max. Typ. Max. Typ. Max. PIA1707SP1R0MN 1.00 100kHz/1.0V 46 42 50 45 1.06 1.3 PIA1707SP1R5MN 1.50 100kHz/1.0V 39 35 46 40 1.5 1.8 PIA1707SP2R2MN 2.20 100kHz/1.0V 32 30 35 32 1.8 2.2 PIA1707SP3R3MN 3.30 100kHz/1.0V 30 28 32 29 2.7 3.3 PIA1707SP4R7MN 4.70 100kHz/1.0V 28 26 29 26 3.7 4.5 PIA1707SP6R8MN 6.80 100kHz/1.0V 24 22 25 22 6.0 7.2 PIA1707SP100MN 10.0 100kHz/1.0V 21 19 22 19 9.2 10.6 PIA1707SP150MN 15.0 100kHz/1.0V 16 14 16 14 12.8 15.5 PIA1707SP330MN 33.0 100kHz/1.0V 12 10 12 10 32 37

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 7. Characteristics Curves: PIA1707SP1R0MN PIA1707SP1R5MN PIA1707SP2R2MN PIA1707SP3R3MN PIA1707SP4R7MN PIA1707SP6R8MN PIA1707SP100MN PIA1707SP150MN PIA1707SP220MN PIA1707SP330MN PIA1707SP470MN PIA1707SP820MN

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 8. Soldering: Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the differenc e in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is t he utilization of hot air. 8-1 Solder Re-flow: Recommended temperature profiles for re-flow soldering in Figure 1. 8-2 Soldering Iron (Figure 2): Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. N o t e : a) Preheat circuit and products to 150°C. b) 355°C tip temperature (Max.) c ) N e v e r c o n t a c t t h e c e r a m i c w i t h t h e i r o n t i p d) 1.0mm tip diameter (Max.) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f ) L i m i t s o l d e r i n g t i m e t o 4 ~ 5 s e c s .

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 C D 2.0±0.5 EMBOSSED CARRIER B A COVER TAPE 9. Packaging Information: 9-1 Reel Dimension: 9 - 2 T a p e D i m e n s i o n : 9-3 Packaging Quantity: Type A(mm) B(mm) C(mm) D(mm) PIA 1707 Chip / Reel 300 Inner box 600 Carton 2400 Series Size Bo(mm) Ao(mm) Ko(mm) P(mm) W(mm) F(mm) T(mm) D(mm)

Molded Choke Coil – PIA1707SP Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 9-4 Tearing Off Force: Application Notice: 1. Storage Conditions: To maintain the solderabililty of terminal electrodes: a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation: a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) Vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. Room Temp. (℃) Room Humidity (%) Room atm (hPa) Tearing Speed mm/min 5~35 45~85 860~1060 300 The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions.