V3020

V3020 EMMICRO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 17

Technical content

Features

‰ Supply current typically 390 nA at 3V ‰ 50 ns access time with 50 pF load capacitance ‰ Fully operational from 1.2V to 5.5V ‰ No busy states or danger of a clock update while accessing ‰ Serial communication on one line of a standard parallel data bus or over a conventional 3 wire serial interface ‰ Interface compatible with both Intel and Motorola ‰ Seconds, minutes, hours, da y of month, month, year, week day and week number in BCD format ‰ Leap year and week number correction ‰ Time set lock mode to prevent unauthorized setting of the current time or date ‰ Oscillator stability 0.3 ppm / volt ‰ No external capacitor needed ‰ Frequency measurement and test modes ‰ Temperature range: -40°C to +85°C ‰ On request extended temperature range, -40°C to +125°C ‰ Pin compatible with the V3021 ‰ TSSO8 and SO8 packages Typical Operating Configuration Address Decoder V3020 RAM XI XO CS RD WR I/O CS RD WR Data Bus CPU or or R/ Address Bus Fig. 1 Pin Assignment CS RD WR VDD I/OVSS XI XO V3020 CS RDWR VDD I/O VSSXI XO V3020 SO8 TSSO8 Fig. 2 EM MICROELECTRONIC - MARIN SA

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 2 www.emmicroelectronic.com Absolute Maximum Ratings Parameter Symbol Conditions Maximum voltage at VDD V DDmax V SS + 7.0V Minimun voltage at VDD V DDmin V SS – 0.3V Maximum voltage at any signal pin Vmax V DD + 0.3V Minimum voltage at any signal pin Vmin V SS – 0.3V Maximum storage temperature TSTOmax +150°C Minimum storage temperature T STOmin -65°C Electrostatic discharge maximum to MIL-STD-883C method 3015.7 with ref. to VSS VSmax 1000V Maximum soldering conditions T Smax 250°C x 10s Table 1 Stresses above these listed maximum ratings may cause permanent damages to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction. Handling Procedures This device has built-in pr otection against high static voltages or electric fields; how ever, anti-static precautions must be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the voltage range. Unused inputs must always be tied to a defined logic voltage level. Operating Conditions Parameter Symbol Min Typ Max Unit Operating temperature T A -40 +125 °C Logic supply voltage V DD 1.2 5.0 5.5 V Supply voltage dv/dt (power-up & power-down)

6 V/µs

Decoupling capacitor 100 nF Crystal Characteristics Frequency f 32.768 kHz Load capacitance C L 7 8.2 12.5 pF Series resistance R S 35 50 kΩ Table 2 1) The maximum operating temperature is confirmed by sampling at initial device qua lification. In production, all devices are tested at +85°C. On request, devices tested at +125°C can be supplied. 2) See Fig. 5 Electrical Characteristics (standard temperature range) VDD= 5.0V ±10%, VSS = 0V and TA=-40 to +85°C, unless otherwise specified Parameter Symbol Test Conditions Min Typ Max Unit Total static supply I SS All outputs open, all inputs at V DD VDD = 3.0V, address 0 = 0 TA = 0 to +°70°C 390 600 490 nA nA Total static supply I SS All outputs open, all inputs at V DD VDD = 5V, address 0 = 0 TA = 0 to +°70°C 460 800 600 nA nA Dynamic current I SS I/O to VSS through 1MΩ RD = VSS, WR = VDD, CS = 4 MHz address 0 = 0, read all 0 300 µA Input / Output Input logic low V IL 1.0 V Input logic high V IH 3.5 V Output logic low V OL I OL = 4 mA 0.4 V Output logic high V OH I OH = 4 mA 2.4 V Input leakage I IN 0.0 < V IN < 5.0V 0.1 1 µA Output tri-state leakage on I/O pin ITS CS high, and address 0, bit 0, low 0.1 1 µA Oscillator Starting voltage V STA 1.2 V Input capacitance on XI C IN T A = +25°C 13 pF Output capacitance on XO C OUT T A = +25°C 9 pF Start-up time T STA 1 s Frequency stability ∆f/f 1.5 ≤ VDD ≤ 5.5V, TA = +25°C 0.3 0.5 ppm/V Frequency Measurement Mode Current source on I/O pin pulsed on/off @ 256 Hz IONF CS high, addr.0, bit 0, high VI/O = 1V 10 25 60 µA Table 3

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 3 www.emmicroelectronic.com Electrical Characteristics (extended temperature range) VDD= 5.0V ±10%, VSS = 0V and TA=-40 to +125°C, unless otherwise specified Parameter Symbol Test Conditions Min Typ Max Unit Total static supply I SS All outputs open, all inputs at V DD VDD = 3.0V, address 0 = 0 µA Total static supply I SS All outputs open, all inputs at V DD address 0 = 0 7 µA Dynamic current I SS I/O to VSS through 1MΩ RD = VSS, WR = VDD, CS = 4 MHz address 0 = 0, read all 0 300 µA Input / Output Input logic low V IL 1.0 V Input logic high V IH 3.5 V Output logic low V OL I OL = 4 mA 0.4 V Output logic high V OH I OH = 4 mA 2.4 V Input leakage I IN 0.0 < V IN < 5.0V 0.1 1 µA Output tri-state leakage on I/O pin ITS CS high, and address 0, bit 0, low 0.1 1 µA Oscillator Starting voltage V STA 1.2 V Supply voltage dV/dt (power- up & power-down) +85°C ≤ TA ≤ +125°C 0.006 6 V/µs Input capacitance on XI C IN T A = +25°C 13 pF Output capacitance on XO C OUT T A = +25°C 9 pF Series resistance of the crystal RS -40°C ≤ TA ≤ +85°C 90 kΩ Start-up time T STA T A = +125°C 1) 10 s Frequency stability ∆f/f 2.0 ≤ VDD ≤ 5.5V, TA = +25°C 0.3 0.5 ppm/V Frequency Measurement Mode Current source on I/O pin pulsed on/off @ 256 Hz IONF CS high, addr.0, bit 0, high VI/O = 1V 8 25 60 µA Table 4 1) Analyses done at high temperature with crystal type Micro Crystal CX2V-02

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 4 www.emmicroelectronic.com The V3020 will run slightly too fast, in order to allow the user to adjust the frequency, depending on the mean operating temperature. This is made since the crystal adjustment can only work by lowering the frequency with an added capacitor between XO and V SS. The printed circuit capacitance has also to be taken into consideration. The V3020 in DIL 8 package, running with an 8.2 pF crystal at room temperature, will be adjusted to better than ±1s/day with a 6.8 pF capacitor. Typical Standby Current at VDD = 3V Fig. 3a Typical Standby Current at VDD = 3V and Extended Temperature Fig. 3b

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 5 www.emmicroelectronic.com Typical Standby Current at VDD = 5.5V Fig. 4a Typical Standby Current at V DD = 5.5V and Extended Temperature Fig. 4b

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 6 www.emmicroelectronic.com Typical Frequency on I/O Pin Typical drift for ideal 32'768 Hz quartz Note: The trimming capacitor value must not exceed 15 pF. Greater values may disturb the oscillator function Fig. 5 Quartz Characteristics OF F∆ = -0.038 2C ppm (T – TO)2 ± 10% ∆F/FO = the ratio of the change in frequency to the nominal value expressed in ppm (it can be thought of as the frequency deviation at any temperature) T = the temperature of interest in °C T O = the turnover temperature (25 ± 5°C) To determine the clock error (accuracy) at a given temperature, add the frequency tolerance at 25°C to the value obtained from the formula above. Fig. 6

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 7 www.emmicroelectronic.com Timing Characteristics (standard temperature range) VSS= 0V and TA=-40 to +85°C, unless otherwise specified V DD ≥ 2V V DD = 5.0V ±10% Chip select duration t CS Write cycle 500 50 ns RAM access time (note 1) t ACC C LOAD = 50pF 300 50 60 ns Time between two transfers t W 500 100 ns Rise time (note 2) t R 10 200 10 200 ns Fall time (note 2) t F 10 200 10 200 ns Data valid to Hi-impedance (note 3) t DF 15 200 15 30 40 ns Write data settle time (note 4) t DW 80 50 ns Data hold time (note 5) t DH 120 25 ns Advance write time t ADW 20 10 ns Write pulse time (note 6) t WC 500 50 ns Table 4 Timing Characteristics (standard temperature range) VSS= 0V and TA=-40 to +125°C, unless otherwise specified V DD ≥ 2V V DD = 5.0V ±10% Chip select duration t CS Write cycle 500 60 ns RAM access time (note 1) t ACC C LOAD = 50pF 300 50 60 ns Time between two transfers t W 500 120 ns Rise time (note 2) t R 10 100 10 100 ns Fall time (note 2) t F 10 100 10 100 ns Data valid to Hi-impedance (note 3) t DF 15 200 15 30 50 ns Write data settle time (note 4) t DW 80 50 ns Data hold time (note 5) t DH 120 25 ns Advance write time t ADW 20 15 ns Write pulse time (note 6) t WC 500 60 ns Table 4 ex. Note 1: t ACC starts from RD or CS , whichever activates last Typically, t ACC = 5 + 0.9 CEXT in ns; where CEXT (external parasitic capacitance) is in pF Note 2: CS , RD , DS , WR and R/ W rise and fall times are specified by tR and tF Note 3: t DF starts from RD or CS , whichever deactivates first Note 4: t DW ends at WR or CS , whichever deactivates first Note 5: t DH starts from WR or CS , whichever deactivates first Note 6: t WC starts from WR or CS , whichever activates last and ends at WR or CS , whichever deactivates first

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 8 www.emmicroelectronic.com Timing Waveforms Read Timing for Intel ( RD and WR Pulse) and Motorola ( DS (or RD pin tied to CS ) and R/ W ) Fig. 7a Write Timing for Intel ( RD and WR Pulse) Fig. 7b Write Timing for Motorola ( DS (or RD pin tied to CS ) and R/ W ) Fig. 7c

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 9 www.emmicroelectronic.com Communication Cycles Read Data Cycle for Intel ( RD and WR Pulse) Fig. 8a Read Data Cycle for Motorola ( DS (or RD pin tied to CS ) and R/ W ) Fig. 8b Write Data Cycle for Intel ( RD and WR Pulse) Fig. 8c Write Data Cycle for Motorola ( DS (or RD pin tied to CS ) and R/ W ) Fig. 8d

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 10 www.emmicroelectronic.com Address Command Cycle for Intel ( RD and WR Pulse) Fig. 8e Address Command Cycle for Motorola ( DS (or RD pin tied to CS ) and R/ W ) Fig. 8f Block Diagram Fig. 9

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 11 www.emmicroelectronic.com Pin Description Pin SO8 TSSO8 Name Function 1 3 XI 32 kHz crystal input 2 4 XO 32 kHz crystal output 3 5 CS Chip select input 4 6 V SS Ground supply 5 7 I/O Data input and output 6 8 RD Intel RD , Motorola DS (or tie to CS ) 7 1 WR Intel WR , Motorola R/ W 8 2 V DD Positive supply Table 5 Functional Description Serial Communication The V3020 resides on the parallel data and address buses as a standard peripheral (see Fig.15 and 16). Address decoding provides an active low chip select ( CS ) to the device. For Intel compatible bus timing the control signals RD and WR pulse and CS are used for a single bit read or write (see Fig. 7a and 7b). Two options exist for Motorola compatible bus timing. The first is to use the control signals DS with R/ W and CS , the second is to tie the RD input to CS and use the control signals R/ W and CS (see Fig. 7a and 7c). Data transfer is accomplished through a single input/output line (I/O). Any data bus line can be chosen. A conventional 3 wire serial interface can also be used to communicate with the V3020 (see Fig. 17). Communication Cycles The V3020 has 3 serial communication cycles. These are: 1) Read data cycle 2) Write data cycle 3) Address command cycle A communication cycle always begins by writing the 4 address bits, A0 to A3. A microprocessor read from the V3020 cannot begin a communication cycle. Read and write data cycles are similar and consist of 4 address bits and 8 data bits. The 4 address bits, A0 to A3, define the RAM location and the 8 data bits D0 and D7 provide the relevant information. An address command cycle consists of only 4 address bits. Read Data Cycle A read data cycle commences by writing the 4 RAM address bits (A3, A2, A1 and A0) to the V3020. The LSB, A0, is transmitted first (see Fig. 8a and 8b). Eight microprocessor reads from the V3020 will read the RAM data at this address, beginning with the LSB, D0. The read data cycle finishes on reading the 8 th data bit, D7. Write Data Cycle A write data cycle commences by writing the 4 RAM address bits (A3, A2, A1 and A0) to the V3020. The LSB, A0, is transmitted first (see Fig. 8c and 8d). Eight microprocessor writes to the V3020 will write the new RAM data. The LSB, D0, is loaded first. The write data cycle finishes on writing the 8th data bit, D7. Address Command Cycle An address command cycle consists of just 4 address bits. The LSB, A0, is transmitted first (see Fig. 8e and 8f). On writing the fourth address bit, A3, the address will be decoded. If the address bits are recognized as one of the command codes E hex or F hex (see Table 6), then the communication cycle is terminated and the corresponding command is executed. Subsequent microprocessor writes to the V3020 begin another communication cycle with the first bit being interpreted as the address LSB, A0. Clock Configuration The V3020 has a reserved clock area and a user RAM area (see Fig. 9). The clock is not directly accessible, it is used for internal time keeping and contains the current time and data. The contents of the RAM is shown in Table 6, it contains a data space and an address command space. The data space is directly accessible. Addresses 0 and 1 contain status information (see Tables 7a and 7b), addresses 2 to 5, time data, and addresses 6 to 9, date data. The address command space is used to issue commands to the V3020. RAM Map Address Dec Hex Parameter BCD range Data Space 0 0 Status 0 1 1 Status 1 2 2 Seconds 00-59 3 3 Minutes 00-59 4 4 Hours 00-23 5 5 Day of month 01-31 6 6 Month 01-12 7 7 Year 00-99 8 8 Week day 01-07 9 9 Week number 00-52 Address Command Space

14 E Copy_RAM_to_clock

15 F Copy_clock_to_RAM

Two commands are available (see Table 6). The Copy_RAM_to_clock command is used to set the current time and date in the clock and the Copy_clock_to_RAM command to copy the current time and date from the clock to the RAM. The Copy_RAM_to_clock command, address data E hex, causes the clock time and date to be overwritten by the time and date stored in the RAM at addresses 2 to 9. Address 1 is also cleared (see section "Time and Date Status Bits"). Prior to using this command, the desired time and date must be loaded into the RAM using write data cycles and the time set lock bit, address 0, bit 4, must be clear (see section "Time Set Lock").

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 12 www.emmicroelectronic.com Status Information The RAM addresses 0 and 1 contain status control data for the V3020. The function of each ibt (0 and 7) within address locations 0 and 1 is shown in Table 7a and 7b respectively. Status Word Status 0 - address 0 0 - inactive 76543210 1 - a c t i v e Read / Write bits Frequency Measurement Mode Reserved Test Mode 0 Test Mode 1 Time Set Lock Reserved Reserved Reserved Table 7a Status 1 - address 1 0 - No change from last Copy_clock_to_RAM 76543210 1 - Change from last Read ONLY bits Copy_clock_to_RAM Seconds Minutes Hours Day of month Month Year Week day Week number Table 7b Reset and Initialization Upon microprocessor recovery from a system reset, the V3020 must be initialized by software in order to guarantee that it is expecting a communication cycle (ie. the internal serial buffer is waiting for the address bit A0). Software can initialize the V3020 to expect a communication cycle by executing 8 microprocessor reads (see Fig. 10). Initializing Access to the V3020 Fig. 10 On first startup or whenever power has failed (VDD < 1.2V) the status register 0 and the clock must be initialized by software Having initialized the interface to expect the address bit A0, write 0 to status register 0, then set the clock (see section "Clock and Calendar"). Time and Date Status Bits There are time and date status bits at address 1 in the RAM. Upon executing a Copy_clock_to_RAM command, the time and date status bits in the RAM show which time and date parameters changed since the last time this command was used. A logic 1 in the seconds status bit (address1, bit 0) in the RAM indicates that the seconds location in the RAM (address 2) changed since the last Copy_clock_to_RAM command and thus need to be read. The seconds location must change before any other time or date location can change. If the seconds status bit is clear, then no time or date location changed since the last Copy_clock_to_RAM command and so the RAM need not to be read by software. Table 7b shows the seconds, minutes, hours, day of the month, month, year, week day, and week number status bit locations. They are set or cleared similar to the seconds location. It should be noted that if the minutes status bit is clear, then the seconds bit may be set, but ail other status bits are clear. Si milarly with hours, the bits representing the units less than hours may have been set, but the bits for the higher units will be clear. This rule holds true for the week day or day of month locations also. The time and date status bits can be used to drive software routines which need to be executed every -second, -minute, -hour, -day of month / weekday, -month, -year, or -week. In this application it is necessary to poll the V3020 at least once every time interval used as it does not generate an interrupt. Upon executing a Copy _RAM_to_clock command, the time and date status bits in the RAM are cleared. Time Set Lock The time set lock control bit is located at address 0, bit 4 (see Table 7a). When set by software, the bit disables the Copy_RAM_to_clock command (see section "Commands".) A set bit prevents unauthorized overwriting of the current time and date in the clock. Clearing the time set lock bit by software will re-enable the Copy_RAM_to_clock command. On first startup or whenever power has failed (V DD < 1.2 V), the time set lock bit must be setup by software.

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 13 www.emmicroelectronic.com Reading the Current Time and Date Send copy_clock_to_RAM addr. F hex Read time and data status bits, addr. 1 Is the seconds status bit set, addr. 1, bit 0 Read seconds, addr. 2 Is the minutes status bit set, addr. 1, bit 1 Read minutes, addr. 3 Similar for hours, day of month, week day, month, year and week number No No Yes Yes Current time and date Fig. 11 Clock and Calendar The Time and date addresses in the RAM (see Table 6) provide access to the seconds, minutes, hours, day of month, month, year, week da y, and week number. These parameters have the ranges indicated on Table 6 and are in BCD format. If a parameter is found to be out of range, it will be cleared on its bei ng next incremented. The V3020 incorporates leap year correction and week number calculation. The week number changes only at the incrementation of the day number from 7 to 1. If week 52 day 7 falls on the 25 th, 26th or 27 th of December, then the week number will change to 0, otherwise it will be week 1. Week days are numbered from 1 to 7 with Monday as 1. Reading of the current time and date must be preceded by a Copy_clock_to_RAM command. The time and date status bits will indicate which time and date addresses changed since the last time the command was used (see Fig. 11). The time and date from the last Copy_clock_to_RAM command is held unchanged in the RAM, except when power (V DD) has failed totally. To change the current time and date in the clock, the desired time an date must first be written to the RAM, the time set lock bit cleared, and then a Copy_RAM_to_clock command sent (see Fig. 12). The time set lock bit can be used to prevent unauthorized setting of the clock. Setting the Current Time and Date Write seconds, minutes, hours, day of month, week day, month, year and week number to the RAM Clear the time set lock bit, addr. 0, bit 4 Send copy_RAM_to_clock command, addr. E hex Set the time set lock bit, addr. 0, bit 4 Fig. 12 Frequency Measurement Setting bit 0 at address 0 will put a pulsed current source (25 µA) onto the I/O pin, when the device is not chip selected (ie. CS input high). The current source will be pulsed on/off at 256 Hz. The period for ± 0 ppm time keeping is 3.90625 ms. To measure the frequency signal on pin I/O, the data bus must be high impedance. The best way to ensure this is to hold the microprocessor and peripherals in reset mode while measuring the frequency. The clarity of the signal m easured at pin I/O will depend on both the probe input impedance (typically 1 M Ω) and the magnitude of the leakage current from other devices driving the line connected to pin I/O. If the signal measured is unclear, put a 200 k Ω resistor from pin I/O to VSS. It should be noted that the magnitude of the current source (25 µA) is not sufficient to drive the data bus line in case of any other device driving the line, but it is sufficient to take the line to a high logic level when the data bus is in high impedance. Use a crystal of nominal C L = 8.2 pF as specified in the section "Operating Conditions". The MX series from Microcrystal is recommended. The accuracy of the time keeping is dependent upon the frequency tolerance and the load capacitance of t he crystal. 11.57 ppm corresponds to one second a day. Test From the various test features added to the V3020 some may be activated by the user. Table 7a shows the test mode b its. Table 8 shows the 3 available test modes and how they can be activated. Test mode 0 is activated by setting bit 2, address 0, and causes all time keeping to be accelerated by 32. Test mode 1 is activated by setting bit 3, address 0, and causes all the time and date locations, address 2 to address9, to be incremented in parallel at 1 Hz with no carry over (independent of each other). The third test mode combines the previous two resulting in parallel incrementing at 32 Hz.

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 14 www.emmicroelectronic.com Test Modes Addr. 0 bit 3 Addr. 0 bit 2 Function 0 0 Normal operation 0 1 All time keeping accelerated by 32 1 0 Parallel increment of all time data at 1 Hz with no carry over 1 1 Parallel increment of all time data at 32 Hz with no carry over Table 8 An external signal generator can be used to drive the divider chain of the V3020. Fig. 13a and 13b show how to connect the signal generator. The speed can be increased by increasing the signal generator frequency to a maximum of 128 kHz. An external signal generator and test modes can be combined. To leave test both test bits (address 0, bits 2 and 3) must be cleared by software. Test corrupts the current time and date and so the time and date should be reloaded after a test session. Signal Generator Connection Fig. 13a Note: The peak value of the signal provided by the signal generator should not exceed 1.5 V on XO. Fig. 13b Note: The peak value of the signal provided by the signal generator should not exceed 1.5 V on XO. Crystal Layout In order to ensure proper oscillator operation we recommend the following standard practices: - Keep traces as short as possible - Use a guard ring around the crystal Fig. 14 shows the recommended layout. Oscillator Layout Fig. 14 Access Considerations The section "Communication Cycles" describes the serial data sequences necessary to complete a communication cycle. In common with all serial peripherals, the serial data sequences are not re-ent rant, thus a high priority interrupt, or another software task, should not attempt to access the V3020 if it is already in the middle of a cycle. A semaphore (software flag) on access would allow the V3020 to be shared with other software tasks or interrupt routines. There is no time limit on the duration of a communication cycle and thus interrupt routines (which do not use the V3020) can be fully executed in mid cycles without any consequences for the V3020.

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 15 www.emmicroelectronic.com Typical Applications V3020 Interfaced with Intel CPU (RD/WR Pulse) Fig. 15 V3020 Interfaced with Motorola CPU (Advanced R/W) Fig. 16

3 Wire Serial Interface

1) With strobe low bits are written to the V30 20, and with strobe high bits are read from the V3020 2) For serial ports with byte transfer only, an address command cycle should be combined with every data cycle to give 8 address bits and 8 data bits. For example to read the current minutes, write address data F + 2 (1111 + 0011) and then read 8 data bits. Fig. 17

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 16 www.emmicroelectronic.com Battery Switch Over Circuit * Use Schottky barrier diodes. The BAT85 has a typical V F of 250 mV at an IF of 1 mA. The reverse current is typically 200 nA at a V R of 5 V. The reverse, recovery time is 5 ns. For surface mount applications use the Philips BAT17 in SOT-23 or other. Fig. 18 Ordering and Package Information Dimensions of 8-Pin SOIC Package 1234 5678 H L 0-8°C E A B e D Dimensions in mm Min. Nom. Max A 1.35 1.63 1.75 A1 0.10 0.15 0.25 B 0.33 0.41 0.51 C 0.19 0.20 0.25 D 4.80 4.93 5.00 E 3.80 3.94 4.00 e1 . 2 7 H 5.80 5.99 6.20 L 0.40 0.64 1.27 Fig. 19 Dimensions of 8-Pin TSSOP Package Fig. 20

R V3020 Copyright © 2005, EM Microelectronic-Marin SA 17 www.emmicroelectronic.com

Ordering Information

When ordering, please specify the complete Part Number Part Number Temperature Range Package Delivery Form Package Marking V3020SO8B 8-pin SOIC Tape & Reel V3020 EM%## V3020SO8A 8-pin SOIC Stick V3020 EM%## V3020TP8B 8-pin TSSOP Tape & Reel 3020 V3020TP8A -40°C to +85°C 8-pin TSSOP Stick 3020 V3020XSO8B 8-pin SOIC Tape & Reel V3020 EM%X## V3020XSO8A 8-pin SOIC Stick V3020 EM%X## V3020XTP8B 8-pin TSSOP Tape & Reel 3020 X V3020XTP8A -40°C to +125°C 8-pin TSSOP Stick 3020 X Where % and ## refer to the lot number and date (EM internal reference only). EM Microelectronic-Marin SA (EM) makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in EM's G eneral Terms of Sale located on the Company's web site. EM assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual pr operty of EM are granted in connection with the sale of EM products, expressly or by implications. EM's products are not authorized for use as components in life support devices or systems. © EM Microelectronic-Marin SA, 03/05, Rev. G