3082105 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
ORIGINAL INSTRUCTIONS DL0122 AIRLINE TYRE INFLATOR MODEL NO: TPG30P PART NO: 3082105
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. SPECIFICATION GENERAL SAFETY PRECAUTIONS 1. Compressed air can be dangerous. En sure that you are thoroughly familiar with all precautions relating to the use of compressors and a compressed air supply. 2. NEVER direct a jet of compressed air at people or animals. 3. ALWA YS ensure that the equipment/tool being used has a safe working pressure exceeding the output pressure of the compressor that it is connected to. 4. NEVER exceed the operating pressure stated in the specification. 5. ALWA YS ensure that the air supply is turned off at the tool outlet and vent all compressed air from the air hose and the equipment attached to it, before disconnecting air hoses or other equipment from your compressor. Weight 0.60 kg Connecting Hose Length 400 mm Max Working Pressure 8 bar/ 116 psi Airline Connection size 1/4” BSP
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 6. Ensure all fixed air connections are properly sealed using teflon tape or pipe sealant. 7. Check the gauge periodically for ac curacy and replace if damaged or inaccurate. OPERATION Under or over inflated tyres are dangerous. Consult vehicle owners handbook before using this tyre inflator. Attach the airline hose to the tyre inflator and fully tighten. Use PTFE tape if needed. Turn on the air supply and check that the airline pressure DOES NOT exceed 8 bar (116psi) 1. Remove the dust cap from the tyre va lve and check that the tyre valve is clean before connecting. 2. Push the connector fully home onto th e tyre valve. If the valve leaks, the connector may need repositioning. Correct position is confirmed by a steady reading on the gauge. 3. Check the tyre pressure on the gauge. 4. Pull the trigger to inflate the tyre. Re -check the tyre pressure. Note that when the trigger is pulled, the gauge will show the airline pressure, not the tyre pressure. 5. To deflate the tyre, partially pull th e trigger and check the pressure again. 6. When the tyre pressure is correct, disconnect and remove the connector. Replace the dust cap on the tyre valve. IMPORTANT: The air pressure gauge on this product is for guidance only. It is important that you check the pressure with an approved, calibrated gauge. 7. Inspect the air hose for wear or da mage periodically and replace if necessary. 8. DO NOT use damaged or leaking hoses. Occasionally clean the product and lubricate the trigger parts. CAUTION: THIS PRODUCT MAY HAVE A LOWER WORKING PRESSURE THAN SOME COMPRESSORS WILL SUPPLY, THEREFORE, AN AIRLINE REGULATOR SHOULD BE INSTALLED. CAUTION: AIRLINE LUBRICATORS SHOULD NOT BE USED WITH THIS ITEM
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY