SPS8040N1R0YF SUPERWORLD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
- PART NO. EXPRESSION : SPS8040 N4R7ME (a) Series code (d) Inductance code : 4R7 = 4.7 yH (a) () ©) @) (eh (b) Dimension code (e) Tolerance code : M=#20%,Y=430% (c) Material code (f) F : ROHS Compliant 2. CONFIGURATION & DIMENSIONS : B 8 c E 5 —— el — a — < x N N AR7 N N q 4 N N K—~! Recommendend Land pattern Unit:m/m Pete te ete tet tet te feofe] 3. MATERIALS : b (a) Core a (b) Wire — (c) Coating (a) Solder qd Void appearance tolerance Limit Size of voids occurring to coating resin is specified below. Exposed wire tolerance limit of coating resin part on product side. a Size of exposed wire occurring to coating resin is specified below. 1. Width direction (dimension a) : Acceptable when a=wi2 Nonconforming when a>w/2 | | 2. Length direction (dimension b) : Dimension b is not specified. 3. The total area of exposed wire occurring to each sides is not greater than 50% of coating resin area, and is acceptable. RoHS Compliant NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 PG.1
External appearance criterion for exposed wire Exposed end of the winding wire at the secondary side should be 3mm and below. es f Electrode appearance criterion for exposed wire I, so Conforming 2 Only top side of wire is exposed. - (regardless of whole tope side of wire exposed) L | ZOm™ Less than 1/2 of joint side length. ~ C (More than 1/2is selected as defect) J less than half of outer diameter is ~ ~ covered with solder. 4. GENERAL SPECIFICATION : (a) All test data referenced to 25°C ambient , Ls:1MHz/1V. (b) Heat Rated Current (Irms) will cause the coil temperature rise approximately At of 40°C (keep 1min.). (c) Saturation Current (Isat) will cause LO to drop 30% typical. (keep quickly). (d) The part temperature (ambient + temp rise) should not exceed 125’Cunder worst case operating conditions. (e) Operating temperature : -40~+125°C f ) Storage Condition (Component in its packaging) i) Temperature: -10°C to 40°C ii) Humidity: 60% RoHS Compliant NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 PG.2
LOW PROFILE POWER INDUCTORS SPS8040N SERIES 5. ELECTRICAL CHARACTERISTICS : Part Number Inductance (nay @ase (uH) Irs (A) Isat (A) 420% | ww [wax [ty | mex | | seconowrore | rom [eso [aon | va00] 1300 | a2 | [ sesonownne | sesame | eae v0 | r100] 11a [100 | [ srssoanesr [rsa [200 [rr [vaof noo [00 | [ srssomanar [aa [rao [ooo [om fom [ns | [ srssoanorarr [oss [soo [a0 [em [rs [160 | [ sesonowrrie | «ram | seo | a0 | ero 600 | wos | [ sesonowsour | saan | sao | sao | cao] seo | 220 | [_sesroanrow [avon | ano [170 | am] 100 | es | [ srstoanssnur—[sszox [is [veo [vw [veo [00 | [seconoveanr [eas | 140 [190 [a6 | 140 | a0] [_sesroanrone | ooa0e | a0 [v0 | vas [a0 | wo | [ srssoansr [50205 [oe [ovo [ra [10 [0 | [ srssoanenr—[reo20% [ont [ome [ror [oes [ooo | [ sesonowzamr | axon | ons [are | ose | oso | eo] NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 (S) PTE LTD @) SUPERWORLD ELECTRONICS .
LOW PROFILE POWER INDUCTORS SPS8040N SERIES 6. CHARACTERISTIC CURVES : SPSBO4ON Series ap CZ ° ? pc CURRENTIA) ° ; SPS8040N Series(1.0UH~3.3uH) SPS8040N Series(4.7uH~22uH) w-ELT TET TET) = (FERTT TTT TT PEEPS ¢EEERSCoo Looe |) LE eee 1 LTT ET TTT Te | "o ° occurrenriay ° ° "8 péturrentiay =“ . SPS8040N Series(33uH~82uH) vn SPS8040N Series(100uH~220uH) 90 —a ae | "RRS (EEE fe POSES LL Ba EEE EE EEE |. I LPT Pere | EET ETP LLTEET TT ET) (CEETT EET TT ® 98 pe turrentia) ° S03 ecurenta) | | NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2075 & SUPERWORLD ELECTRONICS (S) PTE LTD PG.4
- SOLDERING AND MOUNTING : 7-1. Soldering Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 7-1.1 Solder Re-flow : Recommended temperature profiles for re-flow soldering in Figure 1. 7-1.2 Soldering Iron : Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150°C. d) 1.0mm tip diameter (max) b) 355°C tip temperature (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm c) Never contact the ceramic with the iron tip. f) Limit soldering time to 4-5 secs. Wo reaesrcnouey __ s it 2 bees é in 2 = i
2 Gradual,
Time(sec.) Lowen — Cooling | ° Time(sec.) Reflow times: 3 times Max. Iron Soldering times: 1 times Max. Fig.1 Fig.2 RoHS Compliant NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 PG.5
LOW PROFILE POWER INDUCTORS SPS8040N SERIES 8. PACKAGING INFORMATION : 8-1. Reel Dimension \\ COVER TAPE & = | A \\ 8 DO | La EMBOSSED CARRIER / 8-2 Tape Dimension \\ Po > 8 at @o68 6|O0 6 Oo O|O 000000 ees ten hes en eee (= a. Lead) eet Dead © P Lao | ee Elecrcode ae kol_| (bctttom view) ES [-srssnar [seas [aason [eavas [revos [reason] eavos [recor] recor [vero | easor [ovo] 8-3 Packaging Quantity [ee [ee z RoHS Compliant NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 & SUPERWORLD ELECTRONICS (S) PTE LTD PG.6
8-4, Tearing Off Force . The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions. F (referenced ANSI/EIA-481-C-2003 of 4.11 standard) —~__ 166° to 180° Room Temp.| Room Humidity | Room atm | Tearing Speed Top cover tape (°C) (%) (hPa) (mm/min) — Base tape Application Notice 4. Storage Conditions : To maintain the solderabililty of terminal electrodes : a) Temperature and humidity conditions : Less than 40°C and 60% RH. b) Recommended products should be used within 12 months from the time of delivery. c) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation : a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. RoHS Compliant NOTE : Specifications subject to change without notice. Please check our website for latest information. 30.06.2015 ®& PG.7