SPS4012FT SUPERWORLD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

  1. CONFIGURATION & DIMENSIONS : SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 (f)(d) (e)(b) (c)(a) 1. PART NO. EXPRESSION : (c) Powder coating type (a) Series code (b) Dimension code (f) Tolerance code : M=±20%, N=±30% 1.2 Max. A B C

1.6 Typ

Unit:m/m (d) Taping package (e) Inductance code : 2R2= 2.2uH (g) 11~99 : Internal controlled number (g) 1.6 4.0 Standard Pattern 1.3 1.3 S P S 4 0 1 2 F T 2 R 2 M - ƶƶ 20.03.2012 SPS4012FT SERIESLow Profile Power Inductors A B Powder Coating C D EE 3. MATERIALS : (a) Core : Ferrite (b) Wire : Polyurethane Enamelled Copper Wire (c) Solder : M35E (d) Coating : Powder Coating NOTE : Specifications subject to change without notice. Please check our website for latest information. (e) Ink : 70000-00101 Marking (Black)

  1. GENERAL SPECIFICATION : c) Rated DC Current: The less value which is IDC1 or IDC2. b) IDC2 : Based on temperature rise (T: 40°C TYP.) a) IDC1 :Based on inductance change (ǻL/Lo:-30%) @ ambient temp. 25°C f) Resistance to solder heat : 260°C 10secs e) Operating temp. : -40°C to +105°C ( include self temp. rise ) d) Storage temp. : -40°C to +105°C SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 5. ELECTRICAL CHARACTERISTICS : Part No. SPS4012FT1R0Ƒ Inductance 1.0 ( uH ) 0.1V/1M ( Hz ) Frequency Test RDC ( ȍ )±20% Resistance 60m Rated DC Current IDC1 (A) IDC2 ( A ) 2.50 1.50 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. Marking A SPS4012FT1R5Ƒ 1.5 0.1V/1M 75m 2.00 1.40 C SPS4012FT2R2Ƒ 2.2 0.1V/1M 90m 1.65 1.20 E SPS4012FT100Ƒ 10 0.1V/1M 0.24 0.74 0.77 M SPS4012FT150Ƒ 15 0.1V/1M 0.40 0.56 0.60 O SPS4012FT220Ƒ 22 0.1V/1M 0.61 0.51 0.54 Q SPS4012FT330Ƒ 33 0.1V/1M 0.81 0.40 0.42 S Tolerance : M = ±20%, N = ±30% SPS4012FT SERIES Tolerance N N M,N M M M M M M M
  1. IMPEDANCE VS. FREQUENCY CURVES : : SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. 6.1 INDUCTANCE vs. DC CURRENT SPS4012FT SERIES SPS4012FT1R0Ƒ SPS4012FT1R5Ƒ SPS4012FT2R2Ƒ SPS4012FT3R3Ƒ SPS4012FT4R7Ƒ SPS4012FT6R8Ƒ
  1. GENERAL SPECIFICATION : SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. 6.1 INDUCTANCE vs. DC CURRENT SPS4012FT SERIES SPS4012FT100Ƒ SPS4012FT150Ƒ SPS4012FT220Ƒ SPS4012FT330Ƒ
  1. GENERAL SPECIFICATION : SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. 6.2 TEMPERATURE vs. DC CURRENT SPS4012FT SERIES SPS4012FT1R0Ƒ SPS4012FT1R5Ƒ SPS4012FT2R2Ƒ SPS4012FT3R3Ƒ SPS4012FT4R7Ƒ SPS4012FT6R8Ƒ

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. 6. GENERAL SPECIFICATION : 6.2 TEMPERATURE vs. DC CURRENT SPS4012FT SERIES SPS4012FT100Ƒ SPS4012FT150Ƒ SPS4012FT220Ƒ SPS4012FT330Ƒ

SUPERWORLD ELECTRONICS (S) PTE LTD 6. RELIABILITY & TEST CONDITION : Resistance to Soldering heat Vibration Substrate bending ITEM (A total of 6 hours) the condition shown in the above profile for 1 time. 130~150°C and after it has been immersed to a depth 0.5mm with new solder smoothly when the sample is taken out of The specimen shall be stored at standard atmospheric conditions for 1 hour, after which the measurement shall There shall be no damage or problems. The specimen shall be passed through the reflow oven with the solder bath. More than 90% of the electrode sections shall be cowered a temperature of 245±5°C. below for 3±0.2 seconds fully in molten solder M705 with then be preheated for about 2 minutes in a temperature of Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated over the whole of the sample before hard, the sample shall be applied to the 3 directions (X,Y,Z) for 2 hours each. a frequency of from 10 to 55Hz/1 minute repeated should There shall be no mechanical damage. ǻL/Lo±10% There shall be no mechanical damage or The sample shall be soldered onto the printed circuit board and when a vibration having an amplitude of 1.52mm and PERFORMANCE TEST CONDITION electrical damage. The sample shall be soldered onto the printed circuit board in figure 1 and a load applied until the figure in the arrow direction is made approximately 3mm.(keep time 30 secs) PRESSURE ROD figure-1 Solderability New solder More than 90% Mechanical (reflow soldering) be made. 100 20 30 30 20 t = 1.6 Ø4.5 45±2 45±2 10R5 R340 Bending test board ǻL/Lo±10% 300 250 200 150 100 2 min. 10 sec 2 min. or more 150~ 180°C 30 sec Min. (230°C Max.) Soldering (Peak temperature 260±3°C 10sec) Slow cooling (Stored at room temperature) Pre-heating Soldering temperature (°C) 20.03.2012 SPS FT SERIESLow Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information.

SUPERWORLD ELECTRONICS (S) PTE LTD 6. RELIABILITY & TEST CONDITION : Temperature characteristics Dielectric withstand voltage ITEM The sample shall be left for 96±4 hours in an atmosphere the sample has been left in a normal temperature and with a temperature of -25±3°C. Upon completion of the test, the measurement shall be normal humidity for 1 hour. Upon completion of the measurement shall be made after The sample shall be left for 96±4 hours in an atmosphere with a temperature of 85±2°C and a normal humidity. temperature and normal humidity shall be ǻL/L20°C±10%. calculated based on the value applicable in a normal 0~2000 ppm/°C ǻL/L20°C±10% The test shall be performed after the sample has stabilized in an ambient temperature of -20 to +85°C,and the value PERFORMANCE TEST CONDITION AC 100V voltage shall be applied for 1 minute across the top surface and the terminal of this sample High temperature storage Electrical Characteristics Test made after the sample has been left in a normal temperature There shall be no damage or problems. There shall be no mechanical damage. There shall be no mechanical damage. and normal humidity for 1 hour. Change of temperature Moisture storage There shall be no other damage of problems There shall be no mechanical damage. The sample shall be subject to 5 continuous cycles, such as shown in the table 2 below and then it shall be subjected to standard atmospheric conditions for 1 hour, after which measurement shall be made. Duration 85±2°C 1 (Thermostat No.1) 5 sec. or less -25±3°C Temperature 30 min. No.1ĺNo.2 5 sec. or less No.2ĺNo.1 30 min.(Thermostat No.2) Standard atmospheric Standard atmospheric The sample shall be left for 96±4 hours in a temperature of 40±2°C and a humidity(RH) of 90~95%. Upon completion of the test, the measurement shall be made after the sample has been left in a normal temperature and normal humidity more than 1 hour. ǻL/Lo±10% ǻL/Lo±10% Low temperature storage ǻL/Lo±10% ǻL/Lo±10% 20.03.2012 SPS FT SERIESLow Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information.

SUPERWORLD ELECTRONICS (S) PTE LTD 7. PACKAGING INFORMATION : 7-1. Reel Dimension (mm) 100 2.2 7-2 CARRIER TAPE DIMENSIONS (mm) 17.3 13.2 330 120° 7-3 TAPING DIMENSIONS (mm) 12mm W 3.35mm3.5mm 1.55mm Ao Ko Bo TP 0.3mm8.0mm 7-4 QUANTITY 3000pcs/Reel The products are packaged so that no damage will be sustained. 8mm 4 mm StartEnd Leader no component 200mm min. Components Trailer no component 400mm min. user direction of feed T 4.00 2.00±0.05 Ao P A A Ko W 5.50 1.75 Ø1.5+0.1/-0.0 1.5 E Bo E E E 20.03.2012 SPS FT SERIESLow Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information.