SPS3012FT SUPERWORLD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
- CONFIGURATION & DIMENSIONS : SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 (f)(d) (e)(b) (c)(a) 1. PART NO. EXPRESSION : (c) Powder coating type (a) Series code (b) Dimension code (f) Tolerance code : M=±20%, N=±30% 1.2 Max. A B C
1.2 Typ
Unit:m/m (d) Taping package (e) Inductance code : 2R2= 2.2uH (g) 11~99 : Internal controlled number (g) 1.2 3.0 Standard Pattern 1.0 1.0 S P S 3 0 1 2 F T 2 R 2 M - ƶƶ 20.03.2012 SPS3012FT SERIESLow Profile Power Inductors A B Powder Coating C D EE 3. MATERIALS : (a) Core : Ferrite (b) Wire : Polyurethane Enamelled Copper Wire (c) Solder : M35E (d) Coating : Powder Coating NOTE : Specifications subject to change without notice. Please check our website for latest information. Marking (Black)
- GENERAL SPECIFICATION : c) Rated DC Current: The less value which is IDC1 or IDC2. b) IDC2 : Based on temperature rise (T: 40°C TYP.) a) IDC1 :Based on inductance change (ǻL/Lo:-30%) @ ambient temp. 25°C f) Resistance to solder heat : 260°C 10secs e) Operating temp. : -40°C to +105°C ( include self temp. rise ) d) Storage temp. : -40°C to +105°C SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 5. ELECTRICAL CHARACTERISTICS : Part No. SPS3012FT2R2M Inductance 2.2±20% ( uH ) 0.1V/1M ( Hz ) Frequency Test RDC ( ȍ ) Resistance 96m Rated DC Current IDC1(A) IDC2(A) 1.30 1.45 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. Marking E SPS3012FT100M 10±20% 0.1V/1M 0.348 0.64 0.72 M SPS3012FT SERIES Min. (MHz) SRF Max. Typ. 80m 0.15 0.21 0.29 Max. Typ. Typ. 1.70 1.30 1.10 0.85
SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 6. RELIABILITY & TEST CONDITION : Resistance to Soldering heat Vibration Substrate bending ITEM (A total of 6 hours) the condition shown in the above profile for 1 time. 130~150°C and after it has been immersed to a depth 0.5mm with new solder smoothly when the sample is taken out of The specimen shall be stored at standard atmospheric conditions for 1 hour, after which the measurement shall There shall be no damage or problems. The specimen shall be passed through the reflow oven with the solder bath. More than 90% of the electrode sections shall be cowered a temperature of 245±5°C. below for 3±0.2 seconds fully in molten solder M705 with then be preheated for about 2 minutes in a temperature of Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated over the whole of the sample before hard, the sample shall be applied to the 3 directions (X,Y,Z) for 2 hours each. a frequency of from 10 to 55Hz/1 minute repeated should There shall be no mechanical damage. ǻL/Lo±10% There shall be no mechanical damage or The sample shall be soldered onto the printed circuit board and when a vibration having an amplitude of 1.52mm and PERFORMANCE TEST CONDITION electrical damage. The sample shall be soldered onto the printed circuit board in figure 1 and a load applied until the figure in the arrow direction is made approximately 3mm.(keep time 30 secs) PRESSURE ROD figure-1 Solderability New solder More than 90% Mechanical (reflow soldering) be made. 100 20 30 30 20 t = 1.6 Ø4.5 45±2 45±2 10R5 R340 Bending test board ǻL/Lo±10% 300 250 200 150 100 2 min. 10 sec 2 min. or more 150~ 180°C 30 sec Min. (230°C Max.) Soldering (Peak temperature 260±3°C 10sec) Slow cooling (Stored at room temperature) Pre-heating Soldering temperature (°C) 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. SPS3012FT SERIES
SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 6. RELIABILITY & TEST CONDITION : Temperature characteristics Dielectric withstand voltage ITEM The sample shall be left for 96±4 hours in an atmosphere the sample has been left in a normal temperature and with a temperature of -25±3°C. Upon completion of the test, the measurement shall be normal humidity for 1 hour. Upon completion of the measurement shall be made after The sample shall be left for 96±4 hours in an atmosphere with a temperature of 85±2°C and a normal humidity. temperature and normal humidity shall be ǻL/L20°C±10%. calculated based on the value applicable in a normal 0~2000 ppm/°C ǻL/L20°C±10% The test shall be performed after the sample has stabilized in an ambient temperature of -20 to +85°C,and the value PERFORMANCE TEST CONDITION AC 100V voltage shall be applied for 1 minute across the top surface and the terminal of this sample High temperature storage Electrical Characteristics Test made after the sample has been left in a normal temperature There shall be no damage or problems. There shall be no mechanical damage. There shall be no mechanical damage. and normal humidity for 1 hour. Change of temperature Moisture storage There shall be no other damage of problems There shall be no mechanical damage. The sample shall be subject to 5 continuous cycles, such as shown in the table 2 below and then it shall be subjected to standard atmospheric conditions for 1 hour, after which measurement shall be made. Duration 85±2°C 1 (Thermostat No.1) 5 sec. or less -25±3°C Temperature 30 min. No.1ĺNo.2 5 sec. or less No.2ĺNo.1 30 min.(Thermostat No.2) Standard atmospheric Standard atmospheric The sample shall be left for 96±4 hours in a temperature of 40±2°C and a humidity(RH) of 90~95%. Upon completion of the test, the measurement shall be made after the sample has been left in a normal temperature and normal humidity more than 1 hour. ǻL/Lo±10% ǻL/Lo±10% Low temperature storage ǻL/Lo±10% ǻL/Lo±10% 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. SPS3012FT SERIES
SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 7. PACKAGING INFORMATION : 7-1. Reel Dimension (mm) 100 2.2 7-2 CARRIER TAPE DIMENSIONS (mm) 17.3 13.2 330 120° 7-3 TAPING DIMENSIONS (mm) 12mm W 3.35mm3.5mm 1.55mm Ao Ko Bo TP 0.3mm8.0mm 7-4 QUANTITY 3000pcs/Reel The products are packaged so that no damage will be sustained. 8mm 4 mm StartEnd Leader no component 200mm min. Components Trailer no component 400mm min. user direction of feed T 4.00 2.00±0.05 Ao P A A Ko W 5.50 1.75 Ø1.5+0.1/-0.0 1.5 E Bo E E E 20.03.2012 Low Profile Power Inductors NOTE : Specifications subject to change without notice. Please check our website for latest information. SPS3012FT SERIES