SP0115T2A0-CM300DX-24T

2SP0115T2A0-CM300DX-24T POWERINT | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 8

Technical content

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T www.power.com/gate-driver Page 1 2SP0115T2A0-CM300DX-24T and 2SP0115T2A0C-CM300DX-24T Data Sheet Compact, high-performance, plug-and-play dual-channel IGBT driver based on SCALE™-2 technology for individual and parallel-connected modules Abstract The SCALE ™-2 plug -and-play driver 2SP0115T2 A0-CM300DX-24T / 2SP0115T2A0C-CM300DX-24T (Coated version using ELPEGUARD SL 1307 FLZ/2 from Lackwerke Peters with a typical thickness of 50 µm) is a compact dual-channel intelligent gate driver designed for Mitsubishi’s 17mm dual IGBTs CM300DX-24T. The driver features an electrical interface with a built-in DC/DC power supply. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to www.power.com/gate-driver/go/plug-and-play Features Applications  Plug-and-play solution  Allows parallel connection of IGBT modules Shortens application development time  Extremely reliable; long service life  Built-in DC/DC power supply 20-pin flat cable interface  Duty cycle 0... 100%  Active clamping of Vce at turn-off  IGBT short-circuit protection  Monitoring of supply voltage  Safe isolation to EN 50178  UL compliant  Suitable for CM300DX-24T  Wind-power converters  Industrial drives  UPS  Power-factor correctors Traction  Railroad power supplies  Welding  SMPS  Radiology and laser technology  Research  and many others

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 2 Safety Notice! The data contained in this data sheet is intended exclusively for technically trained staff. Handling all high - voltage equipment involves risk to life. Strict compliance with the respective safety regulati ons is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic -sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Important Product Documentation This data sheet contains only product-specific data. For a detailed description, must-read application notes and common data that apply to the whole series, please refer to “Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers” on www.power.com/gate-driver/go/2SP0115T. When applying SCALE -2 plug -and-play drivers, please note that these drivers are specifically adapted to a particular type of IGBT module. Therefore, the type designation of SCALE -2 plug-and-play drivers also includes the type designation of the corresponding IGBT module. These drivers are not valid f or IGBT modules other than those specified. Incorrect use may result in failure. Mechanical Dimensions Dimensions: Refer to “Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers” Mounting principle: Soldered onto 17mm dual IGBT module CM300DX-24T Absolute Maximum Ratings Parameter Remarks Min Max Unit Supply voltage VCC VCC to GND 0 16 V Logic input and output voltages To GND -0.5 VCC+0.5 V SOx current Fault condition, total current 20 mA Gate peak current Iout Note 1 -8 +15 A Average supply current ICC Note 2 290 mA Output power per gate Ambient temperature ≤ 70°C (Note 3) 1.2 W Ambient temperature ≤ 85°C (Note 3) 1 W Switching frequency f 15 kHz Test voltage (50Hz/1min.) Primary to secondary (Note 16) 3800 VAC(eff) Secondary to secondary (Note 16) 3800 VAC(eff) DC-link voltage Note 4 800 V |dV/dt| Rate of change of input to output voltage 50 kV/μs Operating voltage Primary/secondary, secondary/secondary 1200 Vpeak

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 3 Parameter Remarks Min Max Unit Operating temperature Note 20 -20 85 °C Storage temperature Note 21 -40 50 °C Surface temperature Only 2SP0115T2A0C-CM300DX-24T (Note 22) 125 °C Recommended Operating Conditions Parameter Remarks Min Typ Max Unit Supply voltage VCC To GND 14.5 15 15.5 V Resistance from TB to GND Blocking time ≠ 0, ext. value 128 ∞ kΩ SOx current Fault condition, 3.3V logic 4 mA

Electrical Characteristics

Power Supply Remarks Min Typ Max Unit Supply current ICC Without load 33 mA Efficiency η Internal DC/DC converter 85 % Coupling capacitance Cio Primary side to secondary side, total, per channel 23 pF Power Supply Monitoring Remarks Min Typ Max Unit Supply threshold VCC Primary side, clear fault 11.9 12.6 13.3 V Primary side, set fault (Note 5) 11.3 12.0 12.7 V Monitoring hysteresis Primary side, set/clear fault 0.35 V Supply threshold Visox-Veex Secondary side, clear fault 12.1 12.6 13.1 V Secondary side, set fault (Note 6) 11.5 12.0 12.5 V Monitoring hysteresis Secondary side, set/clear fault 0.35 V Supply threshold Veex-VCOMx Secondary side, clear fault 5 5.15 5.3 V Secondary side, set fault (Note 6) 4.7 4.85 5 V Monitoring hysteresis Secondary side, set/clear fault 0.15 V Logic Inputs and Outputs Remarks Min Typ Max Unit Input impedance V(INx) > 3V (Note 7) 3.5 4.1 4.6 kΩ Turn-on threshold V(INx) (Note 8) 2.6 V Turn-off threshold V(INx) (Note 8) 1.3 V SOx output voltage Fault condition, I(SOx) < 8mA 0.7 V

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 4 Short-circuit Protection Remarks Min Typ Max Unit Vce-monitoring threshold Between auxiliary terminals 10.2 V Response time DC-link voltage > 550V (Note 9) 5.4 μs Delay to IGBT turn-off After the response time (Note 10) 1.4 μs Blocking time After fault (Note 11) 90 ms Timing Characteristics Remarks Min Typ Max Unit Turn-on delay td(on) Note 12 75 ns Turn-off delay td(off) Note 12 65 ns Jitter of turn-on delay Note 18 ±2 ns Jitter of turn-off delay Note 18 ±4 ns Output rise time tr(out) Gx to Ex (Note 13) 5 ns Output fall time tf(out) Gx to Ex (Note 13) 10 ns Dead time between outputs Half-bridge mode (Note 19) 3 μs Jitter of dead time Half-bridge mode ±50 ns Transmission delay of fault state Note 14 400 ns Outputs Remarks Min Typ Max Unit Turn-on gate resistor Rg(on) Note 15 2.1 Ω Turn-off gate resistor Rg(off) Note 15 2.5 Ω Gate voltage at turn-on 15 V Gate-voltage at turn-off P=0W -9.2 V P=1.2W -7.1 V Gate resistance to COMx 4.7 kΩ Electrical Isolation Remarks Min Typ Max Unit Test voltage (50Hz/1s) Primary to secondary side (Note 16) 3800 3850 3900 Veff Secondary to secondary side (Note 16) 3800 3850 3900 Veff Partial discharge extinction volt. Primary to secondary side (Note 17) 1220 Vpeak Secondary to secondary side (Note 17) 1200 Vpeak Creepage distance Primary to secondary side 12.6 mm Secondary to secondary side 6.6 mm Primary to NTC 6.5 mm Clearance distance Primary to secondary side 12.3 mm Secondary to secondary side 6.6 mm Primary to NTC 6.5 mm All data refer to +25°C and VCC = 15V unless otherwise specified

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 5 Footnotes to the Key Data 1) The gate current is limited by the gate resistors located on the driver. 2) If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. 3) If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. From 70°C to 85°C, the maximum permissible output power can be linearly interpolated from the given data. 4) This limit is due to active clamping. Re fer to the “Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers”. 5) Undervoltage monitoring of the primary -side supply voltage (VCC to GND). If the voltage drops below this limit, a fault is transmitted to the corresponding outputs and the IGBTs are switched off. 6) Undervoltage monitoring of the secondary -side supply voltage (Visox to Veex and Veex to COMx which correspond with the approximate turn -on and turn -off gate -emitter voltages). If the corresponding voltage drops below this limit, the IG BT is switched off and a fault is transmitted to the corresponding output. 7) The input impedance can be modified to values <18 kΩ (customer-specific solution). 8) Turn-on and turn-off threshold values can be increased (customer-specific solution). 9) The resulting pulse width of the direct output of the gate drive unit for short -circuit type I (excluding the delay of the gate resistors) is the sum of response time plus delay to IGBT turn-off. 10) The turn-off event of the IGBT is delayed by the specified time after the response time. 11) Factory set value. The blocking time can be reduced with an external resistor. Refer to the “Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers”. 12) Measured from the transition of the turn -on or turn-off command at the driver input to direct output of the gate drive unit (excluding the delay of the gate resistors). 13) Output rise and fall times are measured between 10% and 90% of the nominal output swing with an output load of 10Ω and 40nF. The v alues are given for the driver side of the gate resistors. The time constant of the output load in conjunction with the present gate resistors leads to an additional delay at the load side of the gate resistors. 14) Transmission delay of the fault state from the secondary side to the primary status outputs. 15) The gate resistors can be leaded or surface mounted. Power Integrations reserves the right to determine which type will be used. Typically, higher quantities will be produced with SMD resistors and small quantities with leaded resistors. 16) HiPot testing (= dielectric testing) must generally be restricted to suitable components. This gate driver is suited for HiPot testing. Nevertheless, it is strongly recommended to limit the testing time to 1s slots as stipula ted by EN 50178. Excessive HiPot testing at voltages much higher than 850V AC(eff) may lead to insulation degradation. No degradation has been observed over 1min. testing at 3800VAC(eff). The transformer of every production sample shipped to customers has undergone 100% testing at the given value or higher (< 5100VAC(eff)) for 1s. 17) Partial discharge measurement is performed in accordance with IEC 60270 and isolation coordination specified in EN 50178. The partial discharge extinction voltage between primary and either secondary side is coordinated for safe isolation to EN 50178. 18) Jitter measurements are performed with input signals INx switching between 0V and 15V referred to GND, with a corresponding rise time and fall time of 8ns. 19) Note that the dead time may vary from sample to sample. A tolerance of approximately ±20% may be expected. If higher timing precisions are required, Power Integrations recommends using direct mode and generating the dead time externally. 20) A version with extended operating temperature range of –40°C…85°C (2SP0115T2B0) can also be supplied. 21) The storage temperature inside the original package (1) or in case the coating material of coated products may touch external parts (2) must be limited to the given value. Otherwise, it is limited to 90°C. 22) The component surface temperature, which may strongly vary depending on the operating condition, must be limited to the given value for coated driver versions to ensure long -term reliability of the coating material.

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 6 Legal Disclaimer The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. All parameters, numbers, values and other technical data included in the technical information were calculated and determined to our best knowledg e in accordance with the relevant technical norms (if any). They may base on assumptions or operational conditions that do not necessarily apply in general. We exclude any representation or warranty, express or implied, in relation to the accuracy or completeness of the statements, technical information and recommendations contained herein. No responsibility is accepted for the accuracy or sufficiency of any of the statements, technical information, recommendations or opinions communicated and any liability for any direct, indirect or consequential loss or damage suffered by any person arising therefrom is expressly disclaimed.

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 7

Ordering Information

Our international terms and conditions of sale apply. Power Integrations Driver Type # Related IGBT 2SP0115T2A0-CM300DX-24T (Temperature range –20°C…85°C) CM300DX-24T 2SP0115T2A0C-CM300DX-24T (Temperature range –20°C…85°C, CM300DX-24T conformal coating) Product home page: www.power.com/gate-driver/go/2SP0115T Refer to www.power.com/gate-driver/go/nomenclature for information on driver nomenclature Information about Other Products For other drivers, evaluation systems product documentation and application support Please click: www.power.com © 2009…2019 Power Integrations Switzerland GmbH. All rights reserved. We reserve the right to make any technical modifications without prior notice. Version 2.0 from 2019-04-03

SCALE™-2 2SP0115T2A0(C)-CM300DX-24T Data Sheet www.power.com/gate-driver Page 8 Power Integrations Sales Offices WORLD HEADQUARTERS

5245 Hellyer Avenue

San Jose, CA 95138 USA Tel: +1-408-414-9200 Fax: +1-408-414-9765 Email: usasales@power.com AMERICAS EAST

7360 McGinnis Ferry Road

Suwannee, GA 30024 USA Tel: +1-678-957-0724 Fax: +1-678-957-0784 Email: usasales@power.com AMERICAS CENTRAL

333 Sheridan Road

Winnetka, IL 60093 USA Tel: +1-847-721-6293 Email: usasales@power.com AMERICAS WEST San Jose, CA 95138 USA Tel: +1-408-414-8778 Fax: +1-408-414-3760 Email: usasales@power.com CHINA (Shanghai) Room 2410, Charity Plaza No. 88 North Caoxi Road Shanghai, 200030 China Tel: +86-21-6354-6323 Fax: +86-21-6354-6325 Email: chinasales@power.com CHINA (Shenzhen) 17/F, Hivac Building, No 2 Keji South 8th Road, Nanshan District Shenzhen, 518057 China Tel: +86-755-8672-8689 Fax: +86-755-8672-8690 Email: chinasales@power.com GERMANY (AC-DC/LED Sales) Einsteinring 24

85609 Aschheim, Germany

Tel: +49-89-5527-39100 Fax: +49-89-1228-5374 Email: eurosales@power.com GERMANY (Gate Driver Sales) HellwegForum 1

59469 Ense, Germany

Tel: +49-2938-64-39990 Email: gate-drivers.sales@power.com INDIA (Bangalore) #1, 14th Main Road Vasanthangar Bangalore, 560052 India Tel 1: +91-80-4113-8020 Tel 2: +91-80-4113-8028 Fax: +91-80-4113-8023 Email: indiasales@power.com INDIA (Mumbai) Unit: 106-107, Sagar Tech Plaza-B Sakinaka, Andheri Kurla Road Mumbai, Maharashtra 400072 India Tel 1: +91-22-4003-3700 Tel 2: +91-22-4003-3600 Email: indiasales@power.com INDIA (New Delhi) #45, Top Floor Okhla Industrial Area, Phase - III New Delhi, 110020 India Tel 1: +91-11-4055-2351 Tel 2: +91-11-4055-2353 Email: indiasales@power.com ITALY Via Milanese 20

20099 Sesto San Giovanni (MI), Italy

Tel: +39-02-4550-8708 Email: eurosales@power.com JAPAN Kosei Dai-3 Bldg. 2-12-11, Shin-Yokohama, Kohoku-ku Yokohama-shi, Kanagawa Japan 222-0033 Tel: +81-45-471-1021 Fax: +81-45-471-3717 Email: japansales@power.com KOREA RM602, 6FL, 22 Teheran-ro 87-gil, Gangnam-gu Seoul, 06164 Korea Tel: +82-2-2016-6610 Fax: +82-2-2016-6630 Email: koreasales@power.com SINGAPORE

51 Newton Road

#19-01/05 Goldhill Plaza Singapore, 308900 Tel 1: +65-6358-2160 Tel 2: +65-6358-4480 Fax: +65-6358-2015 Email: singaporesales@power.com TAIWAN 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, 114 Taiwan Tel: +886-2-2659-4570 Fax: +886-2-2659-4550 Email: taiwansales@power.com UNITED KINGDOM Building 5, Suite 21 The Westbrook Centre Milton Road Cambridge, CB4 1YG United Kingdom Tel: +44-7823-557-484 Email: eurosales@power.com