EDS1406-001 EUROPA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 2

Technical content

This document must be retained for future reference. It is the responsibility of the person installing the electrical equipment to ensure that the installation meets the requirements of the IET wiring regulations and is therefore ‘fit for purpose’. Factors such as correct selection of components, cable sizing, protective devices and Earth bonding are all critical and should be checked prior to full testing and power-up. Any other regulations applicable to the equipment being installed such as the Machinery Directive and current health and safety legislation must also be adhered to. All connections (including factory made) must be checked for the correct tightness prior to commissioning of the electrical installation. All connections should be inspected periodically to ensure correct tightness. DO NOT USE POWER TOOLS ON THESE PRODUCTS Europa House, Airport Way, Luton, Bedfordshire, LU2 9NH Technical: 01582 692 444 technical@europa-plc.com www.europa-plc.com Data Sheet EDS1406-001 Page 1 of 2 Features & Benefits

  • Modular construction allowing boards to be vertically stacked for separation of lighting and power circuits for metering.
  • Removable gland plates facilitating drilling/ hole punching.
  • Door key lock as standard preventing unauthorised access.
  • Separate modular DIN rail enclosure for timers and modular contactors.
  • Separate extension box for increased wiring space for outgoing cables.
  • Adjustable MCCB/ CBR (160-250A) - Covering a wide range of applications.
  • Generous wiring space for incomer cables (up to 120mm2). No requirement for extension box.
  • SPD and meter-ready. Kits sold separately.
  • Neutral link supplied as standard on 3-pole incoming device.
  • All incomer kits comes complete with the incoming enclosure, links, shrouds and assembly instructions.

Description

  • Type B distribution boards.
  • Available in 8, 12, 16, 20 and 24 three-phase ways.
  • Independently type tested to IEC 61439-3.
  • Complies with the requirements of BS EN 61439-3 / EN 61439-3.
  • Epoxy powder coated RAL7035.
  • IK10 / IP30. 200-250A Three-Phase Type B Distribution Boards and Incomer Kits SLTPN200/250 Distribution Board Description SLTPN200-08 200A TPN 8 Way Board SLTPN250-12 250A TPN 12 Way Board SLTPN250-16 250A TPN 16 Way Board SLTPN250-20 250A TPN 20 Way Board SLTPN250-24 250A TPN 24 Way Board SLTPN200/250 Incomer Kits Description SLTPN250-MSKIT3PNL 3 Pole + Neutral Link Main Switch Incomer Kit SLTPN250-MSKIT4P 4 Pole Main Switch Incomer Kit SLTPN250-MCCBKIT4P 4 Pole MCCB Incomer Kit* (160-250A) SLTPN250-CBRKIT4P 4 Pole CBR Incomer Kit* (160-250A) *Incoming device must be set to 200A for 8-way outgoing board (SLTPN200-08). Note: Maximum palm width for M8 copper tube lug = 23mm.

Europa House, Airport Way, Luton, Bedfordshire, LU2 9NH Technical: 01582 692 444 technical@europa-plc.com www.europa-plc.com Data Sheet EDS1406-001 Page 2 of 2 Outgoing Devices Description EUC1P, EUC2P and EUC3P 10kA MCB, 1-63A, B & C Curve EUC7RC./* 10kA Compact RCBO, 6-40A, B & C Curve EUC7R./** 10kA RCBO, 50-63A, B & C Curve Will also accommodate Europa 6kA devices where installation permits. Technical Characteristics Product Range SLTPN200-08 | SLTPN250-12 / 16 / 20 / 24 Standard(s) BS EN 61439-3 / EN 61439-3 Type B Rated Current (In) 200A (8-way only), 250A Rated Condition Short Circuit Current (Icc) 25kA Rated Operational Voltage (Ue) AC 400V Rated Insulation Voltage (Ui) 690V Rated impulse withstand Voltage (Uimp) 8kV Rated Frequency (f) 50Hz Number of Poles 3 Phase + N + PE Humidity Not exceeding 50% at 40°C and 90% at 20°C Rated Pollution Degree 3 Rated Mechanical Impact Protection Degree IK10 Rated Protection Degree IP30 Rated Diversity Factor for Outgoing Devices (n)* 0.6 (8-Way), 0.5 (12 to 24-Way) as per Table 101 of BS EN 61439-3 *Note: Only applies to continuously and simultaneously loaded circuits. Incoming Device Enclosure 500 500 Cut-out for metering device Aperture for Main Switch/ MCCB/ CBR. Cut-out for fuse carriers/ fuses for Surge Protection Device Cut-out for Surge Protection Device Notes: Front door removed to show enclosure cut-outs. Dimensions in mm. A A B B C C D D E E F F G G H H J J K K L L M M N N P P R R T T DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH: DEBURR AND BREAK SHARP EDGES NAME SIGNATURE DATE MATERIAL: DO NOT SCALE DRAWING REVISION TITLE: DWG NO. SCALE:1:2 SHEET 1 OF 1 WEIGHT: 250TPNBOARD bottom open frame Part Number H (mm) H1 (mm) SLTPN200-08 560 434 SLTPN250-12 640 514 SLTPN250-16 720 594 SLTPN250-20 800 674 SLTPN250-24 880 754 454 540 63 126374 H1 500 H 150 A A B B C C D D E E F F G G H H J J K K L L M M N N P P R R T T DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH: DEBURR AND BREAK SHARP EDGES NAME SIGNATURE DATE MATERIAL: DO NOT SCALE DRAWING REVISION TITLE: DWG NO. SCALE:1:5 SHEET 1 OF 1 WEIGHT: dim sheet 500 414 37463 126 H1 500 H Notes: All dimensions in mm. Front cover assembly removed except on top view to show depth. Outgoing Distributuion Board Incoming Device Enclosure 150 A A B B C C D D E E F F DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH: DEBURR AND BREAK SHARP EDGES NAME SIGNATURE DATE MATERIAL: DO NOT SCALE DRAWING REVISION TITLE: DWG NO. SCALE:1:20 SHEET 1 OF 1 WEIGHT: 250TPNBOARD with back 500 414 37463 126 H1 500 H Notes: All dimensions in mm. Front cover assembly removed except on top view to show depth. Outgoing Distributuion Board Incoming Device Enclosure 150 A A B B C C D D E E F F DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH: DEBURR AND BREAK SHARP EDGES NAME SIGNATURE DATE MATERIAL: DO NOT SCALE DRAWING REVISION TITLE: DWG NO. SCALE:1:20 SHEET 1 OF 1 WEIGHT: 250TPNBOARD with back 500 414 37463 126 H1 500 H Notes: All dimensions in mm. Front cover assembly removed except on top view to show depth. Outgoing Distributuion Board Incoming Device Enclosure 150 A A B B C C D D E E F F DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH: DEBURR AND BREAK SHARP EDGES NAME SIGNATURE DATE MATERIAL: DO NOT SCALE DRAWING REVISION TITLE: DWG NO. SCALE:1:20 SHEET 1 OF 1 WEIGHT: 250TPNBOARD with back 454 540 63126 374H1 500H 150 AA BB CC DD EE FF GG HH JJ KK LL MM NN PP RR TT DRAWN CHK'D APPV'D MFG Q.A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES: LINEAR: ANGULAR: FINISH:DEBURR AND BREAK SHARP EDGES NAMESIGNATUREDATE MATERIAL: DO NOT SCALE DRAWINGREVISION TITLE: DWG NO. SCALE:1:5SHEET 1 OF 1 WEIGHT: dim sheet