SF0140BA03114S ICST | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

140 MHz SAW Filter

16 MHz Bandwidth

Part Number: SF0140BA03114S IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 1 of 3 Micro Networks A Division of Integrated Device Technology

DESCRIPTION

  • 140 MHz SAW bandpass filter with 16 MHz bandwidth in 13.3x6.5mm SMP.
  • RoHS compliant. TYPICAL PERFORMANCE Horizontal : Frequency 5 MHz / div Vertical (from top) Magnitude 10 dB/div Magnitude 1 dB/div Phase Deviation 10 deg/div Group Delay Deviation 200 ns/div Input and Output Impedances Frequency Span : 100-180 MHz Wide Band Response Frequency Span : 0-500 MHz Vertical Scale : 10 dB/div S11 S22

Part Number: SF0140BA03114S IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 2 of 3 Micro Networks A Division of Integrated Device Technology SPECIFICATION Parameter Min Typ Max Units Center Frequency (Fc) 1 139.6 140 140.4 MHz Insertion Loss 2 8.2 11 dB 1 dB Bandwidth 15 16.4 MHz 3 dB Bandwidth 16 17.4 MHz 35 dB Bandwidth 21.1 22 MHz Passband Ripple 3 0.43 1 dB p-p Phase Deviation from Linear 3 3 14 deg p-p Group Delay Variation 3 45 160 ns p-p Absolute Delay 0.94 µs Ultimate Rejection 4 40 44 dB Substrate Lithium Niobate Temperature Coefficient of Frequency -90 ppm/ ˚C Ambient Temperature 25 ˚C System Source and Load Impedance 50 Ω Notes: 1. Average of the lowe r and upper 3 dB frequencies. 2. Average level in the passband. 4. Evaluated over the intervals 20 – 124 MHz and 156 – 280 MHz. MAXIMUM RATINGS Parameter Min Max Units Storage Temperature Range -40 +85 ˚C Input Power Level +17 dBm DC Voltage Between Each Terminal 15 V MATCHING CIRCUIT Component values (minimum inductor Q = 45): Ls1 = 100 nH Cp1 = 33 pF Ls2 = 120 nH Cp2 = 0 pF (not used) Notes: 1. The component values shown above are those used in the Micro Networks test fixture. Optimum values may change depending on board layout. Cp2 may be a capacitor or an inductor. 2. 5% tolerance components or better are recommended. 11 5 1,2,3,4,6, 7,8,9,10,12 Input 50 Ω Source Single Ended Output 50 Ω Load Single Ended

Part Number: SF0140BA03114S IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 3 of 3 Micro Networks A Division of Integrated Device Technology PACKAGE OUTLINE AND RECOMMENDED PCB LAYOUT Pin Configuration:

11 Input

12 Input Return

5 Output

6 Output Return

Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. © 2005 All rights reserved. 15.37 8.53 7.62 2.54 2.59 2.98 2.54 .89 YYJJJM ICS BA03114S NOTE: Dimensions shown are all nominal in millimetres. All tolerances are ±0.15 mm except overall length and width. PACKAGE INFORMATION RECOMMENDED PCB FOOTPRINT