DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Features
TX Output Power: 23dBm TX Gain: 28dB RX Gain: 11.5dB RX NF: 3dB Integrated LNA
Applications
ZigBee® 802.15.4 Based Systems for Remote Monitoring and Control WiFi 802.11b/g 2.4GHz ISM band Smart Meters for Energy Management RF6535SQ Standard 25 piece bag RF6535SR Standard 100 piece reel RF6535TR13 Standard 2500 piece reel RF6535PCK-410 Fully assembled evaluation board and 5 loose pieces DS121107 Package Style: QFN, 20-Pin, 3.5mm x 3.5mm x 0.5mm
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. Nominal Operating Parameters Absolute Maximum Ratings Parameter Rating Unit DC Supply Voltage 5 V Operating Case Temperature -40 to +85 °C Storage Temperature -40 to +150 °C ESD Human Body Model RF Pins 500 V ESD Human Body Model All Other Pins 500 V ESD Charge Device Model All Pins 500 V Moisture Sensitivity Level MSL 2 Maximum Input Power to PA +5 dBm Maximum Input Power to LNA +10 dBm Parameter Specification Unit ConditionMin. Typ. Max. Overall Specifications must be met across supply volt- age, control voltage, and temperature ranges unless otherwise noted. Typical conditions: T = 25°C, VCC = 3.3V, CTL = High Operating Frequency Range 2400 2483 MHz Operating Voltage (VCC) 3.0 3.3 4.2 V Operating Voltage (VCC_BIAS)3 3 . 3 4 . 2 V Leakage Current 45 60 uA V CC = 3.3V, RF = OFF, CTRL, SDN, ANT_SEL = Transmit Parameters Frequency 2400 2483 MHz Input Return Loss 9 Balanced Input Impedance 200 Amplitude Imbalance -1 1 dB Phase Imbalance -15 15 deg Output Return Loss 10 Gain 24 28 dB At rated power Gain Flatness -0.8 0.8 dB Rated Output Power 23 dBm V CC = 3.3V, T = 25°C 22 dBm V CC greater than or equal to 3.3V; Temperature less than or equal to 70°C 21 dBm All conditions Supply current 240 260 mA P O = 23dBm 802.15.4OQPSK Supply current 230 250 mA P O = 22dBm 802.15.4OQPSK Supply current 220 240 mA P O = 21dBm, All conditions Thermal Resistance 55 °C/W V CC = 3.6V, POUT = 23dBm, TREF = 85°C 2nd through 5th harmonic level -45 -42 dBm/MHz Measured using standard 802.15.4OQPSK modulation signal VSWR Stability and load mismatch susceptibility 4:1 VSWR No damage 8:1 Gain settling time 1 10 uS Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical perfor- mance or functional operation of the device under Absolute Maximum Rating condi- tions is not implied. The information in this publication is believed to be accurate and reliable. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents, or other rights of third parties, resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended appli- cation circuitry and specifications at any time without prior notice. RFMD Green: RoHS compliant per EU Directive 2002/95/EC, halogen free per IEC 61249-2-21, < 1000ppm each of antimony trioxide in polymeric materials and red phosphorus as a flame retardant, and <2% antimony in solder.
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. Parameter Specification Unit ConditionMin. Typ. Max. Transmit Parameters (continued) Current sourced through TXCT pin 18.0 mA Voltage drop from TXCT pin to TXP/TXN 0.1 V Receive Parameters Frequency 2400 2483 MHz Gain 9.5 11.5 13.5 dB From antenna to RX pin (entire RX path). Noise Figure 3 4 dB From antenna to RX pin (entire RX path). Current 8 11 mA LNA + Switches Input IP3 7 dBm Gain flatness -0.5 0.5 dB Input return loss 6 8.5 dB Output return loss 7.5 dB Balanced Output Impedance 200 Amplitude imbalance -1 1 dB Phase imbalance -15 15 deg Current sourced through RXCT pin 1 mA Voltage drop from RXCT pin to RXP/RXN 0.1 V Antenna Switch RF-to-Control Isolation 50 dB Measured at any control pin while in TX or RX mode. RF-to-ANT Isolation 17 20 dB Measured from Antenna to RX port while in Transmit mode. Measured from Antenna to TX port while in Receive mode. RF-to-RF Isolation 18 20 dB Measured from TX port to RX port while in receive or transmit modes. Antenna Select Switch Speed 1 uS ANT1 or ANT2 path, TX or RX mode Control Logic Control Logic = HIGH = V CC -0.3 = V CC V SDN and ANT_SEL Control Logic = HIGH 1.7 1.8 3.6 V CTL Control Logic = LOW 0 0.2 V All Logic I/O’s Control Current. Logic HIGH 10 AA l l L o g i c I / O ’ s Control Current. Logic LOW 0.1 AA l l L o g i c I / O ’ s
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. Pin Names and Descriptions Pin Name Description 1S D N Enable/Shutdown pin for entire module. See logic table for operation. 2V C C Voltage Supply. An external 1F capacitor might be needed for low frequency decoupling. 3A N T _ S E L Control pin for Antenna select. See logic table for operation. 4C T L Enable voltage pin for both PA/Transmit Switch and LNA/Receive Switch. See logic table for operation. 5N C No connect pin. Must be left floating. 6A N T 2 This is the common port (antenna). It is matched to 50 and DC-block is provided internally. 7G N D Ground. 8A N T 1 This is the common port (antenna). It is matched to 50 and DC-block is provided internally 9G N D Ground. 10 VCC Voltage Supply. An external 1F capacitor might be needed for low frequency decoupling 11 NC No connect pin. Must be left floating. 12 VCC Voltage Supply. An external 1F capacitor might be needed for low frequency decoupling 13 VCC_BIAS Voltage Supply. An external 1F capacitor might be needed for low frequency decoupling 14 GND Ground. 15 TXCT Center tap for pass-thru DC voltage to TXN and TXP pins that connect to the TXVR SOIC. 16 TXN 100 single ended, 200 differential. 17 TXP 100 single ended, 200 differential. 18 RXCT Center tap for pass-thru DC voltage to RXBN and RXBP pins that connect to the TXVR SOIC. 19 RXBN 100 single ended, 200 differential. 20 RXBP 100 single ended, 200 differential.
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. Package Drawing
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. RF6535 Biasing Instructions Tx Mode
- With the RF source disabled, apply 3.3V to V CC with other controls set to 0V
- Apply 3.0V to SDN and 1.8V to CTL
- Apply 0V to ANT_SEL to select the ANT1 port, or 3.0V to select the ANT2 port CC current should rise to 70mA to 80mA quiescent current
- Enable the RF source; V CC current should rise to a maximum of 200mA depending on output power RX Mode
- With the RF source disabled, apply 3.3V to V CC with other controls set to 0V
- Apply 3.0V to SDN, keeping CTL at 0V
- Apply 0V to ANT_SEL to select the ANT1 port, or 3.0V to select the ANT2 port CC current should rise to 7mA to 8mA
- Enable the RF source; V CC current may increase a few mA depending on output power Logic Table Mode SDN CTL ANT_SEL TX-ANT1 3.0V 1.8V 0V TX_ANT2 3.0V 1.8V 3.0V RX-ANT1 3.0V 0 0V RX-ANT1 3.0V 0 3.0V All OFF 0 0 0
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. Evaluation Board Schematic 1 2 3 4 CTL RF6535 100 strip TX 100 strip 0.1F 3.6nH 0.9pF 50 strip J4 ANT2 50 strip SDN VCC 3.0nH ANT_SEL 3.6nH 1.3nH 15 14 13 12 11 3.6nH 0.9pF 50 strip J3 ANT1 3.6nH 1.3nH 1.8nH 1.0F VCC 4.3nH 0.1F 0.1F CT 100 strip 100 strip 50 strip RX CT BALUN 2450MHz 50 - 200 BALUN 2450MHz 50 - 200
support, contact RFMD at (+1) 336-678-5570 or customerservice@rfmd.com. PCB Design Requirements PCB Surface Finish The PCB surface finish used for RFMD's qualification process is electroless nickel, immersion gold. Typical thickness is 3inch to 8inch gold over 180inch nickel. PCB Land Pattern Recommendation PCB land patterns for RFMD components are based on IPC-7351 standards and RFMD empirical data. The pad pattern shown has been developed and tested for optimized assembly at RFMD. The PCB land pattern has been developed to accommodate lead and package tolerances. Since surface mount processes vary from company to company, careful process development is recommended. PCB Metal Land and Solder Mask Pattern Thermal vias for center slug “C” should be incorporated into the PCB design. The number and size of thermal vias will depend on the application, the power dissipation, and this electrical requirements. Example of the number and size of vias can be found on the RFMD evaluation board layout.