RF5365

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

Features

■ Integrated 2.4GHz to 2.5GHz b/g/n Amplifier, SP3T Switch, and Power Detector Coupler ■ Single Supply Voltage 3.0V to 4.8V ■ Output Power: 11b = 21dBm Meeting Spectral Mask 11n = 18dBm at <3% EVM ■ Low Height Package, Suited for SiP and CoB Designs

Applications

■ Cellular handsets ■ Mobile devices ■ Tablets ■ Consumer electronics ■ Gaming ■ Netbooks/Notebooks ■ TV/monitors/video ■ SmartEnergy RF5365

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 2 of 11 RF5365 Absolute Maximum Ratings Parameter Rating Unit Supply Voltage -0.5 to +5.4 VDC Power Control Voltage (VREG) -0.5 to 3.5 VDC DC Supply Current 500 mA Input RF Power +5 dBm Operating Case Temperature -40 to +85 °C Storage Temperature -40 to +150 °C Moisture Sensitivity MSL2 Caution! ESD sensitive device. RFMD Green: RoHS status based on EU Directive 2011/65/EU (at time of this document revision), halogen free per IEC 61249-2-21, < 1000ppm each of antimony trioxide in polymeric materials and red phosphorus as a flame retardant, and <2% antimony in solder. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Parameter Specification Unit Condition Min Typ Max Compliance IEEE802.11b/g/n Standards; FCC CFG 15.247, .205, .209; EN and JDEC Operating Conditions Temp = -10°C to +70°C (SPEC COMPLIANT); Temp = -40°C to -10°C and +70°C to +85°C (REDUCED PERFORMANCE) Frequency Range 2.4 2.5 GHz Power Supply 3.0 3.3 4.8 V

2.7 V Derated performance

ON 2.80 2.85 2.90 V PA in “ON” state OFF 0 0.2 V PA in “OFF” state Output Power 11n 16.5 17.0 dBm VCC > 3.0 V OFDM 54Mbps 11n 17.5 18.0 dBm VCC > 3.3 V OFDM 54Mbps 11g 18.0 18.5 dBm VCC > 3.3 V OFDM 54Mbps 11b 19.5 21.0 dBm 11 Mbps, CCK, VCC > 3.3 V EVM 11g 4.0 % 18dBm, OFDM 54 Mbps, VCC = 3.3 V to 4.8 V all Temp 3.0 % 16.5dBm, OFDM 54 Mbps, VCC = 3.0 VDC all Temp Adjacent Channel Power POUT = 21Bm, VCC = 3.3v, 11Mbps CCK signal. See note 2 ACP1 -36 -33 dBc +/- 11MHz Offset from carrier ACP2 -56 -52 dBc +/- 22MHz Offset from carrier Gain 23 25 29 dB At rated POUT Gain Variance Slope Channel 40 MHz BW -1.0 +1.0 dB Channel 20 MHz BW -0.5 +0.5 dB Frequency 100 MHz BW -2 +2 dB In-Band variance 2.4GHz to 2.5GHz Out of Band Rejection

2170 MHz 6 8 dBc CW signal

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 3 of 11 RF5365 Parameter Specification Unit Condition Min Typ Max Compliance (continued) IEEE802.11b/g/n Standards; FCC CFG 15.247, .205, .209; EN and JDEC Output Power Range 0 23 dBm Voltage Range 0.1 1.5 VDC Filter Bandwidth 0.1 MHz Sensitivity PDETECT < 0.5 V 10 mV/dB PDETECT > 0.5 V 20 mV/dB Voltage Target at 23 dBm POUT 1.2 V Load Variation ±200 mV up to 3:1 VSWR Current Consumption Quiescent 135 180 mA VCC=3.0V to 4.8 V All Temp Operating 170 220 mA VCC < 4.2 VDC, POUT = 18dBm, 11 n, 50 W,, Temp=25 °C Operating 230 mA VCC < 4.8 VDC, POUT = 17.5dBm, 11 n, 50 W,, All Temp Operating 210 270 mA VCC < 4.2 VDC, POUT = 21dBm, 11b, 50 W, All Temp VREG 3 5 mA T = 25°C FEM Leakage 500 nA VCC = “ON”, VREG = 0.2 VDC, RF OFF VREG Leakage 50 nA Noise Figure 8 9 dB Input Return Loss 8 10 dB Thermal Resistance 52 °C/W VCC=4.8V, VREG=2.95V, C_TX=3.3V, C_TX=3.3, C_RX=C_BT=GND, POUT = 18dBm, Modulation=OFDM 11g, Freq=2.45GHz, DC=100%, T=85°C Harmonics POUT = 21dBm, 1 Mbps, CCK BW = 1 MHz, up to 3:1 load Second -15 dBm 4.80 GHz to 5.00 GHz, VCC = 3.3 V, Temp=25°C Third -20 dBm 7.20 GHz to 7.50 GHz, VCC = 3.3 V, Temp=25°C Stability PA must be stable from 0dBm to 21dBm. CW Signal, No spurs above -41.25dBm for non-harmonic related signals. Output VSWR 4:1 All phase angles, no spurious or oscillations. Ruggedness No Damage Conditions over Voltage and Temperature Output VSWR 10:1 Input Power 0 dBm CW Input Power, VCC = 3.0 V to 4.8 V Input Port Impedance 50 Ω Turn-On/Off Time 1 usec Output stable to within 90% of final gain 2.4GHz Receive Frequency 2.4 2.5 GHz Frequency Insertion Loss 0.8 1.2 dB Insertion Loss Input P1dB 22 dBm Input P1dB Passband Ripple Passband Ripple WiFi RX Mode -0.2 +0.2 dB WiFi RX Mode WiFi RX/BT Mode -0.2 +0.2 dB WiFi RX/BT Mode WiFi RX Port Return Loss 10 12 dB WiFi RX Port Return Loss WiFi RX Port Impedance 50 Ω WiFi RX Port Impedance

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 4 of 11 RF5365 Parameter Specification Unit Condition Min Typ Max Bluetooth® Frequency 2.4 2.5 GHz Insertion Loss 0.8 1.2 dB Bluetooth Port Return Loss 10 12 dB Bluetooth Port Impedance 50 Ω Bluetooth Input P1dB 22 dBm Other Requirements Antenna Port Impedance 50 W Return Loss 10 12 dB In WiFi RX or BT Mode Isolation ANT to RX 20 dB At rated POUT in TX Mode Switch Control Voltage Low 0 0.2 V High 2.7 3.6 V Switch Control Current Low 0.5 uA High 100 uA ESD Human Body Model 1000 V Pin - Ground Charge Device Model 500 V JESD22-C101C. Class III Note 1: The PA must operate with gates bias voltage input at 1% to 99% duty cycle. Note 2: The output power for channels 1 and 11 may be reduced to meet FCC restricted band requirements. Switch Control Logic Truth Table Mode C_TX C_RX C_BT VREG TX Mode High Low Low High RX Mode Low High Low Low BT Mode Low Low High Low Simultaneous Low High High Low

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 5 of 11 RF5365 Performance Plots

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 6 of 11 RF5365

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 7 of 11 RF5365 Evaluation Board Schematic C_BT Vreg C_RX C_TX Pdet 101112 4 5 6 TX RX VCC ANT BT 1nF 1uF 1nF 1uF 10pF 10pF 10pF 10pF 4.7nH Note: Components C5, and C6 may not be needed in the final schematic. This will be dependent on board layout and noise coupling to these pins. TX input connects directly to the transceiver. If no DC is present on this pin, C8 may also be eliminated.

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 8 of 11 RF5365 Evaluation Board Layout Top Layer Mid Layer-1 Mid Layer-2 Bottom Layer Note: For best performance, it is recommended to follow the routing and grounding of the RFMD evaluation board as close as possible. At a minimum, use five ground thermal vias on the package center slug (via size: 12mil hole by 21mil capture pad)

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 9 of 11 RF5365 Pin Out 101112 4 5 6 RX Vreg TX C_TX C_RX C_BT PDet VCC VCC ANT GND BT Package Outline Drawing Note: 1. Pin 1 indicator shaded area 2. Chamfered area is Pin 1 indicator

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 10 of 11 RF5365 PCB Recommendations PCB land patterns for RFMD components are based on IPC-7351 standards and RFMD empirical data. The pad pattern shown has been developed and tested for optimized assembly at RFMD. The PCB land pattern has been developed to accommodate lead and package tolerances. Since surface mount processes vary from company to company, careful process development is recommended. Thermal vias for center slug “B” should be incorporated into the PCB design. The number and size of thermal vias will depend on the application. Example of the number and size of vias can be found on the RFMD evaluation board layout.

RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 DS140527 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 11 of 11 RF5365 Pin Names and Descriptions Pin Name Description 1 RX OUT Receive port for 802.11b/g/n band. Internally matched to 50Ω. DC block required. 2 VREG Regulated voltage for the PA bias control circuit. An external bypass capacitor may be needed on the VREG line for decoupling purposes. 3 TX IN RF input for the 802.11b/g/n PA. Input is matched to 50Ω. DC block required. 4 VCC Supply voltage for the FEM. Power down pin. Apply <0.6 VDC to power down the power amplifier stages. Apply 2.5 VDC to 3.6 VDC to power up. If function is not desired, pin may be connected to VCC or VREG. 5 VCC Supply voltage for the FEM. 6 POWER DETECT Power detector voltage for TX section. PDET voltage varies with output power. May need external decoupling. 7 ANT Port matched to 50Ω. DC block required. 8 GND Ground connection. 9 BT PORT Bluetooth® RF Port. DC block required. 10 C_RX Control pin for WiFi Receive Port. Please see truth table for proper settings. 11 C_BT Control pin for Bluetooth® Port. Please see truth table for proper settings. 12 C_TX Control pin for WiFi Transmit Port. Please see truth table for proper settings. Pkg Base GND Ground connection. The backside of the package should be connected to the ground plane through a short path, i.e., PCB vias under the device are recommended.