PU110 TRUMPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

110 WATT SWITCHING POWER SUPPLIES

DESCRIPTION

The PU110 series of compact, open PCB constructed, AC-DC switching power supplies are capable of delivering 72 to 110 watts of continuous power at 25 CFM forced air cooling or 52 to 80 watts at convection cooling. They operate at 85 to 264VAC input voltage without the need of a selector strap. They are ideally suited for use in small to medium size digitally-based systems, such as point-of-sale equipment, microprocessor based systems, and telecom equipment. All models meet the safety requirements of UL, CSA and IEC.

FEATURES

‧ Recognized or certified by UL, CSA and TÜV ‧ Power Fail Detect (PFD) signal ‧ 100% burn-in ‧ Wide input range 85 to 264VAC ‧ Input surge current protection ‧ Overvoltage protection ‧ Overcurrent protection ‧ Compliant with RoHS requirements INPUT SPECIFICATIONS Input voltage： 85 to 264VAC Input frequency： 47 to 63Hz Input current： 3.20A（rms）for 115VAC 1.80A（rms）for 230VAC Earth leakage current： 0.40mA max. @ 115VAC, 60Hz 0.75mA max. @ 230VAC, 50Hz Safety Standard Approvals ： OUTPUT SPECIFICATIONS Output voltage/current ： See rating chart Total output power ： 110 watts maximum at 25 CFM forced air cooling or 80 watts maximum at convection cooling Ripple and noise ： 1﹪ peak to peak maximum Overvoltage protection ： Provided on output #1 only; set at 112-132﹪ of its nominal output voltage Overcurrent protection ： All outputs protected to short circuit conditions Temperature coefficient ：All outputs ±0.04﹪/ºC maximum Transient response ： Maximum excursion of 4﹪ or better on all models, recovering to 1﹪ of final value within 500us after a 25﹪ step load change PFD signal ： TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5﹪ below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation. ENVIRONMENTAL SPECIFICATIONS Operating temperature: 0ºC to +70ºC Storage temperature: -40ºC to +85ºC Relative humidity: 5﹪ to 95 ﹪ non-condensing Derating: Derate from 100﹪ at +50ºC linearly to 50﹪ at +70ºC Cooling: 110 watts continuous output power at 25 CFM forced air cooling or 80 watts at convection cooling EMC Performance (EN55024) EN55022: Class B conducted, Class B radiated FCC: Class B conducted, Class B radiated VCCI: Class B conducted, Class B radiated EN61000-3-2: Harmonic distortion, Class A EN61000-3-3: Line flicker EN61000-4-2: ESD, ± 8KV air and ± 4KV contact EN61000-4-3: Radiated immunity, 3V/m EN61000-4-4: Fast transient/burst, ± 1KV EN61000-4-5: Surge, ± 1KV diff., ± 2KV com. EN61000-4-6: Conducted immunity, 3Vrms EN61000-4-8: Magnetic field immunity, 1A/m EN61000-4-11: Voltage dips, 30% reduction for 500ms and >95% reduction for 10ms GENERAL SPECIFICATIONS Switching frequency: 20KHz to 250KHz, varies with load and line Efficiency: 70﹪ minimum on single output models with Vo≥12V, 65% minimum on the others Hold-up time: 12 msec minimum at 110VAC Line regulation: ±0.5﹪ maximum at full load Inrush current: 15 amps @ 115VAC or 30 amps @ 230VAC, at 25ºC cold start Withstand voltage: 3000VAC from input to output 1500VAC from input to ground 500VAC from output to ground MTBF ： 400,000 hours minimum at full load at 25ºC ambient, calculated per MIL-HDBK-217F Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● www.TRUMPower.com UL 60950-1 CSA C22.2 No. 60950-1 TÜV EN60950-1 PU110 SERIES (LVD) RoHS (Touch current)

UNIVERSAL INPUT PU110 SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Output #1 Output #2 Output #3 Output #4 Maximum (3)(4) Output Ipeak PU110-10-1A 3.3V 0A 22A 3% (N/A) (N/A) (N/A) 72W PU110-10A 5V 0A 22A 3% (N/A) (N/A) (N/A) 110W PU110-12A 12V 0A 9.0A 2% (N/A) (N/A) (N/A) 110W PU110-13A 15V 0A 7.5A 2% (N/A) (N/A) (N/A) 110W PU110-14A 24V 0A 4.5A 2% (N/A) (N/A) (N/A) 110W PU110-16A 30V 0A 3.6A 2% (N/A) (N/A) (N/A) 110W PU110-23A +5V 0A 10A 3% +12V 0A 5A 9.0A 3% (N/A) (N/A) 110W PU110-31A +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% (N/A) 110W PU110-32A +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% (N/A) 110W PU110-40A +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% -5V 0A 1A 4% 110W PU110-41A +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% +24V 0A 1A 4% 110W PU110-42A +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PU110-45A +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 0A 1A 4% 110W PU110-45-1A +5V 2.0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 1.5A 3A 10% 110W PU110-45-2A +5V 0A 10A 3% +24V 0A 3A 5.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PU110-46A +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% -5V 0A 1A 4% 110W NOTES: 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watts. 2. 110 watts maximum at 25 CFM forced air cooling or 80 watt s maximum at convection cooling, except model PU110-10-1A which is rated maximum 60W at convection cooling or 72W at 25 CFM forced air cooling. 3. Safety agency approvals are for the above listed models in PCB for mat. To order models with metallic L-bracket or box, change suffix “A” to “B” for L-bracket format, to “C” for enclosed format (mechanical details shown in page 6-1), e.g. PU110-31C. 4. The output #1 of model PU110-45-1A needs a minimum cu rrent of 2A to support the other outputs at their maximum rated loads. PIN CHART 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13 PU110-10-1A PU110-12A PU110-14A PU110-10A PU110-13A PU110-16A OUTPUT #1 RETURN RETURN OUTPUT PU110-23A OUTPUT COMMON RETURN COMMON RETURN OUTPUT PU110-31A PU110-32A OUTPUT COMMON RETURN COMMON RETURN OUTPUT #2 P.F.D. OUTPUT #3 KEY N.C. PU110-40A PU110-42A PU110-45-1A PU110-46A PU110-41A PU110-45A PU110-45-2A OUTPUT COMMON RETURN COMMON RETURN OUTPUT #2 P.F.D. OUTPUT #3 KEY OUTPUT Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● www.TRUMPower.com PIN MODEL MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. 4. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal 5. Weight: 640 grams (PCB format). 6. The copper pad of the m ounting hole near P1 is for system grounding through a metallic stand-off to system chassis.