4500619 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 20
Technical content
OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS DL1123 CORDLESS IMPACT WRENCH MODEL NO: CIR184LiP PART NO: 4500619
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Impact Wrench. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PRODUCT OVERVIEW The CIR184LIP is a professional, cordless impact wrench which is rechargeable using the mains power adaptor. The key design features are shown above. Upon receipt, check the components against the following list. Any damage or deficiency should be reported to your CLARKE dealer immediately.
- 18V Impact Wrench with battery pack (4000 mAh) fitted Battery-charging unit (not shown) Spare battery pack (4000 mAh) (not shown)
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY PRECAUTIONS WORK ENVIRONMENT 1. Keep the work area clean and tidy and free from trip hazards. 2. DO NOT wear loose clothing or jewellery. Tie long hair out of the way. 3. If wearing gloves, make sure that th ere is no frayed material that could catch in rotating parts. 4. DO NOT use in damp or wet conditions. Keep the work area well lit. DO NOT use where a risk of fire or explosion is present. 5. Although the wrench may be used outdoors, DO NOT leave it exposed to the elements. AVOID direct sunlight, direct heat, rain/moisture etc. 6. ALWAYS keep body and clothing dry.NEVER work in damp area without adequate insulation against electric shock. 7. ALWAYS store this product in a secure place out of reach of children or untrained users. 8. ALWAYS keep equipment dry, especially the battery & battery charger. 9. NEVER over-reach. Keep proper footing and balance at all times and adopt a comfortable, well balanced working position for ongoing work. GENERAL USE 1. This product vibrates during use. Vibra tion may be harmful to your hands or arms. Stop using the wrench if discomfort, a tingling feeling or pain occurs and seek medical advice before resuming use. 2. ALWAYS use ear defenders for prolonged work. Exposure to high noise levels can cause permanent hearing problems. 3. ALWAYS wear impact resistant eye protection in case of flying projectiles. 4. ALWAYS stay alert and use common sense - DO NOT use this product when you are tired or under the influence of alcohol or medication. 5. ALWAYS ensure the workpiece is firmly secured leaving both hands free to control the wrench. Hold the impact wrench correctly and be ready to control sudden movements. 6. ALWAYS check for any damage or condition that could affect the wrench’s operation. Any damaged part should be properly repaired. 7. NEVER force or misuse the wrench. It will do a better and safer job at the rate for which it was designed. 8. NEVER use the wrench if it is defective / operating abnormally.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 9. NEVER carry the wrench with your finger on the trigger. 10. NEVER abuse the mains cable of the battery charger. Never yank the cable to disconnect it from the socket. Keep the cable away from sharp edges/hot surfaces. 11. NEVER use this wrench for any purpose other than described in this booklet. 12. NEVER carry out any alterations or modifications to this product. 13. NEVER wipe the wrench clean with solvents. Wipe plastic parts with a soft cloth, slightly dampened with soapy water. 14. NEVER attempt any repairs yourself. If you have a problem with this product contact your local CLARKE dealer. 15. ALWAYS use an approved cable extension suitable for the power rating of the battery charger (see specifications), the conductor size should also be at least the same size or larger than that on the charger. When using a cable reel, always unwind the cable completely. IMPACT WRENCH SAFETY INSTRUCTIONS could shatter and cause injury. 2. ALWAYS finish tightening nuts with a torque wrench to the correct torque as recommended by the vehicle manufacturer. 3. ALWAYS avoid excessive use of the wrench. When tightening a nut or bolt, always avoid over tightening. 4. ALWAYS ensure the wrench has stopped before putting it down after use. 5. ALWAYS set the forward/reverse selection bar to neutral when changing sockets or when the wrench is not required for immediate use. This will avoid accidental starting. LITHIUM-ION BATTERY USE AND CARE 1. Only use the wrench with the batter y pack supplied. Use of any another battery pack may create a risk of injury and fire. 2. DO NOT charge the battery when the room temperature is below 10oC. DO NOT store the battery where the temperature may exceed 40oC (104oF) 3. When the battery pack is not in use, keep it away from metal objects that could make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 4. Dispose of spent batteries correctly as they contain Lithium-ion. They are re- cyclable and should be taken to a recycling centre to be disposed of as stipulated by local regulations. DO NOT incinerated battery as it may
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com explode when exposed to fire. DO NOT attempt to open, disassemble, modify or service a battery pack. 5. Handle batteries so as to avoid dama ge, fire, corrosion or personal injury. 6. NEVER crush, puncture, short external contacts or dispose of in fire or water. 7. NEVER attempt recharging the battery by means of an engine generator or a DC power source. 8. NEVER attempt to disassemble the battery. 9. NEVER make direct contact with a leaking battery.If you come into contact with battery liquid take the following immediate action: Wash affected area immediately wi th plenty of water, then seek immediate medical attention. SAFETY SYMBOLS The full technical specification of the battery charger is printed on a label on the charger. The meanings of the markings and symbols are shown below Please keep these instructions in a safe place for future reference. Read instruction manual before use Suitable for indoor use only Wear eye protection when using this product. Maximum Temperature (battery pack only) Class 2 Double Insulated Do not Incinerate (battery pack only) WEEE directive compliance required for Lithium-Ion batteries. Do not immerse in water Caution: loud noise when in operation, wear ear protection.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ELECTRICAL CONNECTIONS The battery charger for this product is provided with a standard 3 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used. If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows. The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red. We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD) If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself. This symbol indicates that this is a Class II product, and does not require an earth connection. WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE Plug must be BS1363/A approved. Always fit a 3 Amp fuse. Ensure that the outer sheath of the cable is firmly held by the clamp Neutral (Blue) Live (Brown)
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com BATTERY CHARGING The battery will have been shipped in a low charge state and will require charging before use. 1. Press the battery release clip on the front of the battery pack and slide the battery pack from the impact wrench. 2. Plug the charger into a 230V power supply and switch ON. The green POWER ON light will illuminate to show the unit is connected to the mains supply. 3. Insert the battery pack into the battery charger, noting that it will only fit one way. The red light will flash to indicate the battery is starting to charge. When charging is complete (typically after about 1.5 hours), the green light will come on and the red light will go off. The battery pack can be considered charged and be removed. Charging time will be dependant upon the initial state of the battery. When charging a new battery pack, it may initially not accept full charge. This is common & does not indicate a fault. It can be recharged fully after it has been discharged a couple of times. If charging does not take place, ensure all connections are clean. 4. After charging, switch off and unplug the charger from the power supply. 5. Remove the battery pack from the charger and slide it back onto the impact wrench until it clips into place. The battery pack should slide in easily. If it is not to be fitted immediately, ensure that the metal contacts are protected to avoid the possibility of a short circuit which would cause battery damage. For maximum battery life, we recommend that you maintain the battery in a fully charged state.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com BATTERY CHARGING LIGHTS & FAULT CODES When the battery is fully charged, the battery charger will stop charging and switch to standby. The are no restrictions on how long a battery can remain in the charger, though it is recommended to remove the battery from the charger once the battery is fully charged. The following charts will help you identify the charging sequence and troubleshooting any fault codes. Troubleshooting the battery and the battery charger during charging: CHECKING THE BATTERY STATUS To check the battery status, press the battery status button (1) on the end of the battery. The following blue lights will show how much power is in the battery. Lights 2, 3 & 4 showing: 100% power Lights 2 & 3 showing: 66% power Light 2 showing: 33% power Charger Status Light Status Red Light Green Light Power On, Ready State Off On Charging On Off Finished Charging Off On Battery Temperature is too High Off Flash Battery Failure Flash Off Light Display Possibl e Fault Possible Action Green Light Flashing The battery is ok, but there is a temperature deviation Charge the battery in surroundings where the temperature is between 5°C (41°F) and 40°C (104°F). Wait for the battery to cool down. Red Light Flashing The voltage of the battery is too low. Circuit inside battery is open Contact CLARKE service department for new battery.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OPERATION FITTING A SOCKET 1. Make sure the forward/reverse selector bar is in the middle locked position. 2. Align the chosen socket and simply push it onto the anvil. Use only ½” square drive impact sockets as listed on page 14. FORWARD/REVERSE SELECTION 1. Select the direction of operation by pushing the selector bar in the appropriate direction. The direction of rotation is shown on the end face of the selector bar. When the selector bar is in the central position the trigger is locked and the trigger will not activate the impact wrench. 2. Always check the direction of rotati on before operation by squeezing the trigger to start the impact wrench. Release the trigger to stop. CAUTION: MAKE SURE THAT THE IMPACT WRENCH IS LOCKED USING THE SELECTOR BAR BEFORE ATTACHING OR REMOVING A SOCKET. ALWAYS TAKE CARE TO USE THE CORRECT SIZE SOCKET FOR BOLTS AND NUTS. AN INCORRECT SOCKET WILL CAUSE DAMAGE TO THE BOLT OR NUT.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SPEED SELECTION 1. Three running speeds are available by clicking the speed selection button (5) shown, a green light will show which speed has been selected. The speeds are as follows: 1: 1000 RPM 2: 1500 PRM 3: 2100 RPM 4: On Indicator Light 5: Speed Selection Button LOOSENING A NUT 1. Fit the appropriate socket to the 1/2” square drive of the impact wrench. 2. With the FORWARD/REVERSE switchba r in the REVERSE running position, hold the wrench firmly and pull the trigger. The nut will be impacted repeatedly until it is loosened. NOTE: As the battery becomes discharged the power available will drop. The battery will cut out when a low state of charge is reached. This is normal and is a design feature to protect the battery from deep discharge. If this occurs, re-charge the battery as described on page 8. 3. After use, recharge the battery pack as shown on page 8. Avoid leaving the batteries in a discharged state. TIGHTENING A NUT 1. Start the nut by hand, ensuring it is not cross threaded, then with the appropriate socket fitted to the impact wrench, place it on the nut. 2. With the FORWARD/REVERSE selector bar in the forward running position, and holding the wrench firmly, pull the trigger. 3. Install each nut in turn until it is ‘nipped’ up only - DO NOT tighten fully. When all nuts are secure, tighten further but take care to prevent over- tightening. WARNING: ENSURE THAT THE CORRECT SOCKET IS BEING USED FOR THE NUTS ON YOUR PARTICULAR VEHICLE. AN INCORRECT SOCKET SIZE WILL DAMAGE THE HEADS OF THE BOLTS/NUTS.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 4. ALWAYS finish tightening with a torque wrench to the manufacturers recommended torque. BELT HOOK The impact wrench is provided with a belt hook. This can be fitted to either side of the main housing, adjacent to the battery and is retained by a single screw. TROUBLESHOOTING If the following does not solve your problem contact the CLARKE service dept. PROBLEM CAUSE SOLUTION Unit will not start Battery pack not installed properly Check battery pack installation Battery pack not charged Check battery pack charging requirements Internal components too hot Allow the tool to cool down Battery pack will not charge Battery pack not inserted into charger Insert battery pack into charger until the light illuminates Charger not plugged in to supply Plug charger into a working outlet Surrounding air temperature too hot or too cold Move battery pack to a surrounding air temperature is between 5°C (41°F) and 40°C (104°F)
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com MAINTENANCE All bearings etc. in this wrench are lubricated with a sufficient amount of high grade lubricant for the machines lifetime under normal operating conditions, therefore no further lubrication is required. Refer to your CLARKE dealer if internal maintenance is required. Check the battery charger power cable to ensure it is free from cracks, bare wires etc. Avoid using solvents when cleaning plastic parts, most plastics are susceptible to damage from the various types of commercial solvents. Keep the unit clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent. Your CLARKE impact wrench has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer. Always store the wrench and its charger in the case supplied. Store in a clean, dry place, out of reach of children when not in use. ENVIRONMENTAL PROTECTION DO NOT dispose of this product with general household waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE). Unit shuts off abruptly Battery pack has reached its maximum thermal limit Allow battery pack to cool down Out of charge. (To maximize the life of the battery pack it is designed to shutoff abruptly when the charge is depleted) Place battery on charge PROBLEM CAUSE SOLUTION
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com Through the purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility. BATTERY DISPOSAL Dispose of old batteries in accordance with local authority regulations. DO NOT incinerate or crush, as this will increase the risk of explosion and contamination. If the battery contents come into contact with skin or the eyes, rinse with clean water for several minutes and seek medical advice immediately afterwards. ACCESSORIES A wide range of impact wrench accessories is available from your nearest CLARKE dealer, for further information, contact your nearest dealer, or telephone CLARKE International Sales department on 01992 565300. Suitable impact wrench compatible socket sets include the following: Part No Model No Description
3110875 CIS12/10 10 piece 1/ 2”square drive (metric)
1800311 CIS12/17B 16 piece 1/2” square drive (metric/AF)
1800305 CIS9/32 32 piece 3/8” & 1/ 2”square drive (metric/AF)
1700616 PRO216 4 piece 1/2”square drive spline set
1800356 CIS12/6HB 6 piece 1/2”square drive hex impact sockets metric
1800361 CIS12/7SB 7 piece 1/2”square drive TRX Star Impact Bits
1700584 PRO184 3 piece 1/2”square dr ive Alloy Wheel Thin Wall Set
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SPECIFICATIONS Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. FEATURE SPECIFICATION Weight 2.62 kg Dimensions (L x W x H) 212 x 214 x 74 mm Size of spindle (Drive Size) 1/2” (12.5mm) Motor Speed 3300 bpm (impact rate) Max rated tightening torque 400 Nm Impacts/minute (No Load Speed) Low =1000 rpm Medium =1500 rpm High = 2100 rpm Duty Cycle S1 (continuous) IP Rating IP20 Charger insulation class II Input voltage 230V/50 Hz Output voltage 18V DC Battery Type Lithium-Ion Charging Time Approx. 1.5 hour with 4Ah battery Nominal charge/ discharge current 4A/35A Charger Fuse Rating 3 Amp Sound pressure level 90.9 dB LpA Sound power level 102 dB LWA Uncertainty Factor (K) 3 m/s Vibration Level 9.4 m/s2 Uncertainty Factor (K) 1.5 m/s2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT PARTS LIST
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com No Description No Description
1 Aluminum Shield 17 Gearing
2S c r e w 1 8 G e a r i n g P i n s
3 Gasket 19 Gear Pin Gasket
4 Aluminum Head 20 Bearing
5 Anvil 21 Collar
6 T Type Anvil Washer 22 Motor
7 T Type Bearing 23 Back Cover
8 Steel Ball 24 Activation Switch
9 Impact Block 25 PCB Board
10 Steel ball 26 Light Cover
11 Impact Block Washer 27 Battery Indicator
12 Forward/Reverse Switch 28 Battery
13 Shell 29 Belt Hook
14 Screw 30 Screw
15 Spring 31 Heat Shrink Tubing
16 Anvil 32 Nameplate
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - UKCA
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - CE