PR4403 PREMA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 12

Technical content

0.9 V Boost Driver PR4403 for White LEDs in Solar Lamps

The PR4403 is a single cell step-up converter for white LEDs operating from a single rechargeable cell of 1.2 V supply voltage down to less than 0.9 V. An adjustable light threshold input enables an automatic switching of the LED light, e. g. by an additional light sensor or by the battery charging solar cell itself . Only three external components are required for operation of a white LED. The PR4403 is recommended for mean LED currents of up to 40 mA. This makes PR4403 ideal for use in low-cost or small-sized light applications such as solar LED lamps, LED flashlights or LCD backlighting for portable devices.

FEATURES

  • only one 1.2 V battery cell needed
  • 250 mA peak output current
  • low number of external components
  • battery deep discharge protection
  • adjustable light threshold for switching on

APPLICATIONS

  • Solar garden lamps: The "classic" application for PR4403
  • Advertising objects as well as house numbers can be backlighted to make them visible and stand out during nighttime
  • LED indicator lights with solar cells: Such as electronic traffic signs, illuminated control- and road markers, warning signs and similar
  • Solar powered LED torches
  • Model making, solar powered toys: Creative designers will find thousands of ways utilizing PR4403 for outstanding products TYPICAL APPLICATION Vcc Gnd Vout PR4403 1.2 V White LED LS Solar Cells RLS SWITCHING BEHAVIOUR (EXAMPLE) VLS ILED VoffVon The inductance L1 determines the LED current: Inductance L1 Mean current 47 µH 6.5 mA 32 µH 8.3 mA 26.7 µH 10.8 mA 14.7 µH 14 mA 10 µH 22 mA 6.8 µH 32 mA 4.7 µH 40 mA measured with inductor Murata type LQH32CN series
  • 10 - 22 µH: one white LED
  • 4.7 - 6.8 µH: two white LEDs in parallel For output currents higher than 20 mA an additional blocking capacitor at Vcc is recommended. The circuit is operating in case the pin LS is not connected or connected to Gnd (can be chosen). The circuit is shut down if the voltage at LS is higher than Voff. © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 1/12

n.c. Vcc n.c. Vout Gnd <version code> <lot/date code> Pin No Pin Name Pin Function Description 1 test test pin - do not connect

2 LS LS - Enable Pin

3 Vout Output voltage,

Connect both pin 3 and 6! 4 n.c. Not connected

5 Gnd Ground connection

6 Vout Output voltage,

Connect both pin 3 and 6! 7 n.c. not connected

8 Vcc Supply voltage

Ref. Vcc Vout Comp. Control Logic Comp.LS Ref. Vcc Gnd Vout Comp. Control Logic LS Ref. ABSOLUTE MAXIMUM RATINGS Parameter Min Max Units VCC (no damage) -0.3 8 [V] VLS (no damage) -0.3 6 [V] Operating Temperature Range -20 85 [°C] Storage Temperature Range -55 150 [°C] Electrostatic Discharge (ESD) Protection 2 [kV] © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 2/12

Electrical Characteristics

Parameter Conditions Min Typ. Max Units Supply Voltage, min. operating min. startup max. operating L1 = 10...14.7 µH Ta = 25°C 1.90 0.70 0.90 0.80 0.95 [V] [V] [V] Supply Voltage, min. operating min. startup max. operating L1 = 10...14.7 µH Ta = 0...60°C 1.90 0.80 1.00 0.90 1.05 [V] [V] [V] LED Mean Current (at VLS < Voff) measured with L1 type LQH32CN Murata L1 = 47 µH L1 = 32 µH L1 = 26.7 µH L1 = 22 µH L1 = 14.7 µH L1 = 10 µH L1 = 6.8 µH L1 = 4.7 µH 6.5 8.3 10.8 [mA] [mA] [mA] [mA] [mA] [mA] [mA] [mA] Switching Current at Vout Vout = 0.4 V 250 [mA] Switching Frequency 500 [kHz] Threshold Voff at LS *) Vcc > 950 mV Ta = 25°C Ta = 0...60°C 0.26 0.27 0.28 [V] [V] Threshold Von at LS *) Vcc > 950 mV Ta = 25°C Ta = 0...60°C 0.21 0.22 0.23 [V] [V] Quiescent supply current VLS > Voff VLS < Von Vcc > 850 mV Vcc = 600 mV Vcc = 400 mV Vcc > 850 mV Vcc = 600 mV Vcc = 400 mV 100 < 10 100 < 10 [µA] [µA] [µA] [mA] [µA] [µA] Input resistance of LS input series resistor R1 resistor to Gnd R2 400 [k ]Ω [k ]Ω Internal reference (bandgap) Vref 200 [mV] Efficiency 80 [%] Vout 15 [V] © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 3/12

0.5 Ω or 1 Ω 470 nF 0.5 Ω or 1Ω LS Depending on test setup and measuring method, efficiency values can vary by approx. ±5 %, and peak current values can vary by up to ±20 %, Accuracy of mean currents: ±1 mA. Measuring conditions for all diagrams, unless otherwise noted:

  • Ta = 25°C A LQH32CN from Murata has been used as reference inductor, the DC resistance is specified as
  • 0.44 Ω ± 30 % for 10 µH (max. current 300 mA)
  • 0.71 Ω ± 30 % for 22 µH (max. current 250 mA)
  • 1.30 Ω ± 30 % for 47 µH (max. current 170 mA) The LS pin is not connected. CALCULATION OF THE EFFICIENCY Efficiency %= T ∫ T V LED⋅I LED dt T ∫ T V in⋅I in dt ⋅100 OSCILLOSCOPE DISPLAYS LED voltage (CH1) and LED current (CH2, over 0.5 Ω resistor) (Oscillscope images taken with PR4401. PR4403 shows similar behaviour, but may vary in detail.) with L1 = 22 µH with L1 = 10.0 µH © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 4/12

Characteristic Performance Curves 0,8 1 1,2 1,4 1,6 1,8 2 22 µH 10 µH 6.8 µH 4.7 µH Supply Voltage [V] LED Mean Current [mA] 0,8 1 1,2 1,4 1,6 1,8 2 100 22 µH 10 µH 6.8 µH 4.7 µH Supply Voltage [V] Efficiency [%] 0,8 1 1,2 1,4 1,6 1,8 2 100 150 200 250 300 350 22 µH 10 µH 6.8 µH 4.7 µH Supply Voltage [V] LED Peak Current [mA] © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 5/12

USE OF THE PR4403 IN A SOLAR GARDEN LAMP Vcc Gnd Vout PR4403 1.2 V White LED LS Solar Cells RLS Solar cell as a battery charger and light sensor The PR4403 offers good properties to realize a step-up driver for one white LED powered by only one rechargeable 1.2V battery cell charged by a 2.4 V solar cell. The diode is recommended to be a 1N5819 Schottky diode. No additional photo sensor is required as the solar cell operates here as a light sensor. The resistor R LS determines the light threshold at which the LED is automatically switched on (see Threshold voltage VON and VOFF in „SWITCHING BEHAVIOUR“). A typical value of R LS when using a solar cell is 1.2 MΩ. RSL AS A LIGHT SENSOR Vcc Gnd Vout PR4403 1.2 V White LED LS Solar Cells RLS Photo resistor RLS works as a light sensor The resistor on the LS pin can be replaced by a photo resistor (for example a CDS resistor) instead of using the solar cell as light sensor. Depending on the light resistance of the photo sensor an additional series resistor can be connected to the LS pin. INCREASING THE THRESHOLD VOLTAGE AT THE LS PIN A series resistor can be used in case that a higher threshold voltage (V ON) is necessary at the LS pin. The resistor can be calculated as follows: RLS= V ON⋅R2 Vref −R1R2 with

  • R1, R2 and Vref specified in “Characteristics“ (page 2)
  • VON: desired threshold voltage
  • RLS: external resistor on the LS pin For example: A threshold voltage of 1 V is desired: RLS = 1 V x 400 kΩ / 200 mV – (30 kΩ + 400 kΩ) = 1.57 MΩ The following table defines the series resistor at LS: Threshold Voltage VON RLS 1.9 V 3.3 MΩ 1.0 V 1.5 MΩ 0.72 V 1.0 MΩ

0.4 V 390 kΩ

© PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 6/12

SELECTION OF INDUCTORS FOR PR4403 The inductor should be selected according to the required LED current. Using lower inductances than specified may lead to erratic behaviour, especially at low supply voltages and should be avoided. Operating with higher inductances is possible and will lead to lower supply and LED current. However the quiescent current which is independent of the inductance will lead to a lower overall efficiency. While the series resistance of the coil has a small impact on the LED current, it is important that the saturation current is higher than the maximum peak current over the supply voltage range. Inductors optimized for DC-DC converters are mostly suitable. LED COMPATIBILITY It must be considered that the peak current through the LED is up to 7 times higher than the mean current. LED lifetime may be affected if operated outside the range specified by the LED vendor. Since the emission spectrum of white LEDs usually depends on the current, the light color may shift to blueish white. High peak currents may also saturate the LED and reduce the light efficiency of the LED. If the rated LED peak current is exceeded, it is recommended to use a smoothing capacitor and diode to provide a continuous output current (see below „Operation of LED with smoothed current (rectifier)“). With most standard LEDs, this will improve the overall performance with inductors of 10 µH and less, or mean output currents of 23 mA and more. Note that with the higher currents of PR4403 the current rating of standard LEDs might be exceeded, and more powerful or multiple LEDs should be used. CONNECTION FROM BATTERY Due to high peak currents, it is important to connect the PR4403 to the battery with short, low resistance wires, to achieve the best performance. A voltage drop along the wire affects LED current, efficiency and minimum startup and operating voltage. This is most critical for applications with low inductivity and high current. In cases where a longer wire from the battery cannot be avoided, a capacitor should be placed close to the Vcc and Gnd pin of PR4403. Typically a few 100 nF will be enough. Operating at higher currents, a blocking capacitor is usually necessary even if wires or board layout are optimized. USING DIFFERENT BATTERY TYPES The input voltage must be 1.9 V at maximum. At higher voltages the circuit may not trigger and start up correctly. Therefore operation with one Alkaline, NiCd, or NiMH cell (AA or AAA type) is recommended. Alkaline button cells can also be used for supply. However, since high peak currents are drawn from the battery, button cells are recommended only with inductors of 22 µH or more, depending on the battery type. A capacitor at the supply pins of PR4403 may also improve performance with button cells. Lithium batteries are not suitable due to their higher voltage. Battery Lighting Duration (typical) L1= 14.7 µH, LED mean current 15 mA L1= 10 µH, LED mean current 23 mA AA (Mignon, LR 6/AM-3) 40 h 27 h AAA (Micro, LR 03/AM-4) 16 h 8 h Conditions: One white LED connected, measured with single 1.5 V TDK Alkaline battery. Battery lifetime depends on battery capacity and operating conditions. Therefore the times indicated here can only give a rough indication of achievable times. © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 7/12

CONNECTING SEVERAL LEDs IN PARALLEL When several LEDs are connected in parallel, it is necessary to match the forward voltage of these LEDs, to achieve a uniform brightness. The total current of all LEDs together corresponds approximately to the mean output current for operation with one LED. Vcc Gnd Vout PR4403 Vbat =1.5 V L1=10 µH Matching White LEDs LS OPERATION OF A LED WITH SMOOTHED CURRENT (RECTIFIER) Vcc Gnd Vout PR4403 Vbat =1.5 V L1 White LED S LS With a diode (preferably a Schottky diode) and a smoothing capacitor the voltage at the LED can be buffered. Output current and efficiency are typically higher than without a capacitor, especially in the high-current range, due to different load characteristics. The capacitance must be small enough so that the voltage at the capacitor will exceed a voltage of 2.5 V in the first cycle, otherwise the circuit may not start up. In most cases, values between 100 nF and 1 µF are appropriate. The LS pin is not connected or connected to a light sensor (see above). CONNECTING TWO LEDs IN SERIES It is possible to operate PR4403 with two LEDs in series at the output. However, while the peak output current is nearly independent of the output load, the mean output current with two LEDs in series is reduced to half the current with one LED. In addition, at high output voltages the efficiency drops significantly, depending on operating conditions, and current pulses become shorter and sharper. Therefore, although possible and useful in some cases, this operation mode is not recommended for general applications and not specified further. USING RED, GREEN or YELLOW LEDs Although PR4403 is optimized for operation with white or blue LEDs, it will usually also work with red, green or yellow LEDs, with the following restrictions: a) The LED must build up a sufficient forward voltage to trigger PR4403. Due to the internal resistance of the LED, this condition is usually met. However, no guarantee can be assumed for proper operation under all conditions, and you need to qualify the system yourself b) Due to the different forward voltage level and internal resistance of coloured LEDs, the timing is different, and mean currents are mostly lower than for white LEDs. Also other parameters may deviate from this data sheet. © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 8/12

PR4403 SO8 package in plastic tubes All parts delivered, comply with RoHS. Finish is pure tin. © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 9/12

© PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 10/12

© PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 11/12

Information provided by PREMA is believed to be accurate and correct. However, no responsibility is assumed by PREMA for its use, nor for any infringements of patents or other rights of third parties which may result from its use. PREMA reserves the right at any time without notice to change circuitry and specifications. Life Support Policy PREMA Semiconductors products are not authorized for use as critical components in life support devices or systems without the express written approval of PREMA Semiconductor. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PREMA Semiconductor GmbH Robert-Bosch-Str. 6

55129 Mainz Germany

Phone: +49-6131-5062-0 Fax: +49-6131-5062-220 Email: prema@prema.com Web site: www.prema.com © PREMA Semiconductor GmbH 2006-2014 I rev. 1014 Page 12/12