PR3BMF11NSZ SHARP | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
I Outline Dimensions (Unit : mm) I Absolute Maximum Ratings *1 The derating factors of absolute maximum ratings due to ambient temperature are shown in Fig.1, 2 *2 AC for 1 min, 40 to 60%RH, f=60Hz Parameter Symbol Rating Unit Forward current IF 50 1.2 mA Reverse voltage RMS ON-state current Repetitive peak OFF-state voltage Peak one cycle surge current Input Output VR 6 V A V Isurge 12 (50Hz sine wave) 600 A VDRM Viso (rms) IT (rms) kVIsolation voltage −40 to 125 °C Operating temperature Topr −30 to 105 °C Storage temperature Tstg Soldering temperature T sol 260 (For 10s) 4.0 (Ta=25°C) 1. Various types of home appliances. I Features I Applications 8-Pin DIP Type, Large Output current SSR 1. Compact 8-pin dual-in-line package type. 2. RMS ON-state current IT(rms):1.2A 3. High repetitive peak OFF-state voltage. (VDRM:MIN. 600V) 4. Isolation voltage between input and output. (Viso(rms):4kV) 5. Under preparation for UL and CSA. Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occ ur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/ Terminal , and are common ones of cathode.To radiate the heat, solder all of the lead pins on the pattern of PWB. θ Anode mark θ:0 to 13˚ 2.54±0.25 6.5±0.5 1.2±0.3 9.66±0.5 3.5±0.5 7.62±0.3 2.9±0.5 3.25±0.5 0.5±0.1 0.5TYP. 0.26±0.1 R3BMF1 6 5 1 2 3 4 1 3 4 Cathode Anode Cathode Cathode G T 8 6 5 2 3 4 Internal connection Diagram
Input Forward voltage I F=20mA ON-state voltageOutput VD=6V Critical rate of rise of OFF-state voltage VD=1/√−2 • VDRM Transfer charac- teristics Minimum trigger current VD=6V, RL=100Ω VD=6V, RL=100Ω, IF=20mA MIN. 100 5×1010 TYP. 1.2 1011 MAX. 1.4 3.0 Holding current Symbol VF VT IH dV/dt IFT Isolation resistance RISO IT=1.2A Unit V Reverse current V R=3V VD=VDRM IR Repetitive peak OFF-state current I DRM mA −− 10 µA −− 100 µA V/µs − − 10 mA Ω V (Ta=25˚C) Turn-on time −− 100ton µs DC=500V, 40 to 60%RH I Electrical Characteristics 0.2 0.4 1.2 0.8 1.0 0.6 1.4 −30 −20 −1 00 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 1 3 0 RMS ON-state current IT (rms) (A) Ambient temperature Ta (˚C) Forward current IF (mA) Ambient temperature Ta (˚C) −30 −20 −1 00 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 1 3 0 Fig.1 RMS ON-state Current vs. Ambient Temperature Fig.2 Forward Current vs. Ambient Temperature
G The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. G Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. G Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). G Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. G If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. G This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. G Contact and consult with a SHARP representative if there are any questions about the contents of this publication.