PQ1UXX1M2ZPH SHARP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Sheet No.: OP06027 Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Parameter Symbol Rating Unit 300 V mA VInput voltage 350 mW Power dissipation Junction temperature 150 Operating temperature -30 to +85 Storage temperature -55 to +150 Soldering temperature 270(10s) Features Outline Dimensions Lead finish:Lead-free solder plating (Composition: Sn2Cu)

Applications

Product mass:(0.015g) Low Output Current, Compact Surface Mount Type Low Power-Loss Voltage Regulators 1.Compact surface mount package (2.9×1.6×1.1mm) 2.Low power-loss (Dropout voltage: TYP. 0.11 V at I O=60mA) 3.High ripple rejection (TYP. 70dB) 4.Built-in ON/OFF control function (Dissipation current at OFF-state: MAX. 1μA) 5.Built-in overcurrent, overheat protection functions *It is available for every 0.1V of output voltage (1.3V to 5.0V) 6.RoHS directive compliant 1.Cellular phones 2.Cordless phones 3.Personal information tools (PDA) 4.Cameras/Camcoders 5.PCMCIA cards for notebook PCs (Ta=25°C) ON/OFF control terminal voltage Output current VIN VC IO PD Tj Topr °C Tstg Tsol *1 All are open except GND and applicable terminals. *2 At mounted on PCB *3 Overheat protection may operate at Tj=125°C to 150°C (1.9) (0.95) (0.95) (0.3) 15 MAX. Control circuit 5 4 1 2 3 ( ) : Typical dimensions GND Noise reduction (Nr) Model Line-up Output Voltage (TYP.) Model No. Output Voltage (TYP.) Model No. 1.8V 2.5V 2.8V 3.0V 3.3V PQ1U181M2ZPH PQ1U251M2ZPH PQ1U281M2ZPH PQ1U301M2ZPH PQ1U331M2ZPH 3.5V 5.0V PQ1U351M2ZPH PQ1U501M2ZPH (Unit : mm) DC input (VIN) ON/OFF control terminal (VC) DC output (VO) 3.3MAX. (2.9TYP. excluding remaining gate) 5-0.4±0.1 1.3MAX 1.1±0.2 0 to 0.1 0.15±0.1 1.6±0.2 0.2MIN. 2.8±0.3 0.2MIN. U Lead finish identification mark

Sheet No.: OP06027

Electrical Characteristics

V mA mA dB V V Parameter Output peak current Recommended output current Load regulation Line regulation Temperature coefficient of output voltage Ripple rejection Output noise voltage Dropout voltage ON-state voltage for control ON-state current for control Symbol Conditions MIN. TYP. MAX. Unit -300 - 150 - 10 50 - 20 100 3.0 20 0.05 RR 70 - 0.11 0.20 1.8 53 0 0.4 Quiescent current -Output OFF-state dissipation current 1 PQ1Uxx1M2ZPH Series Output voltage VO Refer to the following table.1

4 Iop - 180

-- - RegL1 RegL2 RegL3 Io=5 to 60mA Io=5 to 100mA Io=5 to 150mA 160 mV mV mV RegI VIN=VO(TYP)+1V to VO(TYP)+6V - mV TCVO IO=10mA, Tj=-25 to +75°C -- mV/°C Refer to Fig.2 - Vno(rms) VI-O1 VI-O2 IO=60mA IO=150mA Refer to the following table.2 μV 0.26 0.4 VC(ON) -- - IC(ON) VC=1.8V OFF-state voltage for control VC(OFF) -- V Iq IO=0mA 130 200 μA μA μAIqs VC=0.2V 4 Output current shall be the value when output voltage lowers 0.3V from the voltage at IO=30mA. 5 Input voltage when output voltage falls 0.1V from that at Vin=Vo(TYP)+1.0V. 6 In case that the control terminal ( ③ pin) is open, output voltage should be OFF state. PQ1U251M2ZPH PQ1U281M2ZPH PQ1U331M2ZPH PQ1U351M2ZPH PQ1U501M2ZPH 2.5602.52.440 PQ1U181M2ZPH 1.8601.81.740 2.8602.82.740 PQ1U301M2ZPH 3.0603.02.940 3.3663.33.234 V 3.5703.53.430 5.1005.04.900 VO Symbol MIN. TYP. MAX. UnitModel No. Table.1 Output Voltage (VIN=VO(TYP)+1.0V, IO=30mA, VC=1.8V, Ta=25°C) Table.2 Output Noise Voltage PQ1U251M2ZPH PQ1U281M2ZPH PQ1U331M2ZPH PQ1U351M2ZPH PQ1U501M2ZPH PQ1U181M2ZPH 15 PQ1U301M2ZPH 30 Symbol MIN. TYP. MAX. UnitModel No. Vno(rms) A A A V Fig.1 Test Circuit Iq, Iqs VIN VC IC (ON) RL IO VO (Unless otherwise specified,VIN=VO(TYP) + 1.0V, Io=30mA,Vc=1.8V, Ta=25°C)

8 Excluding PQ1U181M2ZPH

7 In case of PQ1U181M2ZPH, VIN minimum=2.3V.

Sheet No.: OP06027 PQ1Uxx1M2ZPH Series eo Fig.2 Test Circuit for Ripple Rejection ei VIN VC RL f=400Hz(sine wave) ei(rms)=100mV V IN=VO(TYP)+1.0V VC=1.8V IO=10mA RR=20log(ei(rms)/eo(rms)) Fig.3 Power Dissipation vs. Ambient Temperature Fig.4 Overcurrent Protection Characteristics (Typical Value) Fig.5 Output Voltage Fluctuation vs. Junction Temperature (PQ1U281M2ZPH)(Typical Value) Fig.6 Output Voltage vs. Input Voltage (PQ1U281M2ZPH)(Typical Value) Ambient temperature Ta (°C) Note) Oblique line portion:Overheat protection may operate in this area. Relative output voltage (%) 100 0 0.1 0.2 0.3 0.4 Output current I O (A) –60 –10 –20 –30 –40 –50 –30–20 140 120100806040200 Junction temperature T j (°C) Output voltage VO (V) Input voltage VIN (V) 01234567 Power dissipation PD (mW) 100 200 300 400 -30 -25 0 25 50 75 85 100 125 150 Ta=25°C

Sheet No.: OP06027 PQ1Uxx1M2ZPH Series Fig.9 Quiescent Current vs. Junction Temperature (Typical Value) Fig.10 Ripple Rejection vs. Input Ripple Frequency (PQ1U281M2ZPH)(Typical Value) Fig.11 Dropout Voltage vs. Output Current (Typical Value) –30–20 140 120100806040200 Junction temperature Tj (°C) 200 160 120 180 140 100 VIN=VO+1V VC=1.8V IO=0A Ripple rejection RR (dB) 0.1 1 10 100 Input ripple frequency f (kHz) Cn : No Dropout voltage VI-O (mV) 300 250 200 150 100 0 20 40 60 80 100 120 140 Output current I O (mA) Fig.7 Circuit Operating Current vs. Input Voltage (PQ1U281M2ZPH)(Typical Value) Fig.8 Dropout Voltage vs. Junction Temperature (PQ1U281M2ZPH)(Typical Value) Circuit operating current IBIAS (mA) Input voltage VIN (V) 01234567 Dropout voltage VI-O (V) 0.35 0.3 0.25 0.2 0.15 0.1 0.05 –30–20 140 120100806040200 Junction temperature Tj (°C) VI-O2 : IO=150mA VI-O1: IO=60mA VIN : Voltage when output voltage is 95% Ta=25°C VC=1.8V VIN : Voltage when output voltage is 95%