PQXXXDZ01Z SHARP | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Low Power-Loss Voltage Regulator (1) Output current :1 A (2) Low dropout voltage: MAX. 0.5 V(Io=o.5 A) (3) Built-in ON/OFF control function (4) Built-in overcurrent protection, overheat protection (5) SC-63 package. (1) AV equipment. (2) OA equipment. Output voltage(VO ) Taping Sleeve Package type 3.3 V 5.0 V Outline DimensionsFeatures
Applications
(Unit : mm) D5-0209041/2 PQxxxDZ01Z series ( ) : Typical dimensions 0.5 0.2 0.1 Epoxy resin (0.5) (1.7)(0.9) (0.5) (0 to 0.25) 6.6MAX. 9.7MAX. 5.50.52.5MIN. 5.2±0.5 2.3± 0.5 4 (1.27) 1 2 3 4 5 050DZ01 Internal connection Parameter Symbol Ratings Unit V in V C IO Pd Tj Topr Tstg Tsol 150 - 30 to +85 - 40 to +150 260 (for 10s) V V A W Input voltage ON/OFF control terminal voltage Output current Power dissipation Junction temperature Operating temperature Storage temperature Soldering temperature *1 All are open except GND and applicable terminals. *2 Pd: With infinite heat sink. *3 Overheat protection may operate at 125≤Tj≤150˚C. (Ta=25˚C) PQ033DZ01Z PQ033DZ01ZP PQ033DZ01ZZ PQ050DZ01Z PQ050DZ01ZP PQ050DZ01ZZ (In case of PQ050DZ01Z Series) DC input(Vin) ON/OFF control terminal(Vc) DC output(Vo) NC GND Specific IC 1 3 Absolute Maximum Ratings (Notice)
- In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
- Specifications are subject to change without notice for improvement. (Internet)
- Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://sharp-world.com/ecg/) Under development New product
Low Power-Loss Voltage Regulator
Electrical Characteristics
Test Circuit for Ripple Rejection (Unless otherwise specified,Vin=Vo(TYP.)+2V,Io=0.5A,Vc=2.7V,Ta=25˚C) Parameter Symbol Conditions MIN. TYP. MAX. Unit Output voltage Vo - 3.201 4.85 5.0 3.3 5.15 3.399 V Load regulation RegL Io=5mA to 1.0A - 0.1 1.0 % Line regulation RegI *4 , Io=5mA 0.1 1.0 % Temperature coefficient of output voltageTcVo Tj=0 to125˚C ,Io=5mA - ±0.01 - %/˚C Ripple rejection RR - 60 - dB Dropout voltage Vi-o *5, Io=0.5 A - 0.2 0.5 V *6 ON-state voltage for controlV C(on) - 2.0 - V OFF-state voltage for controlV C(off) - 0.8 V Quiescent current Output OFF-state dissipation currentIqs Iq Io=0A Io=0A, VC =0.4V 3 5 mA ON-state current for control OFF-state current for control IC(on) IC(off) V C =2.7V V C =0.4V - µA µA µA 200 PQ050DZ01Z PQ033DZ01Z *4 PQ033DZ01Z : Vin = 4.3 to 8.3 V, PQ050DZ01Z :Vin =6 to 10 V *5 PQ033DZ01Z : Vin = 3.7 V PQ050DZ01Z : Input voltage shall be the value when output voltage is 95% in comparison with the initial value. *6 In case of opening control terminal 2 , output voltage turns off. R LIq IO VO 0.33µF 47 µF 47 µF V IN VC A A A V VC 1 3 IO R LVIN ei eo 2.7 V0.33µF 1 3 f=120Hz(sine wave) IO =0.3 A ei(rms)=0.5 V RR=20log(ei(rms)/eo(rms)) Vin=7 V Vin=5.3 V Ic
G The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. G Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. G Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). G If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. G This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. G Contact and consult with a SHARP representative if there are any questions about the contents of this publication.