PM75DSA120

PM75DSA120 POWEREX | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Single Phase IGBT Inverter Output

75 Amperes/1200 Volts

Outline Drawing and Circuit Diagram 641 Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: h Complete Output Power Circuit h Gate Drive Circuit h Protection Logic – Short Circuit – Over Current – Over Temperature – Under Voltage Applications: h Inverters h UPS h Motion/Servo Control h Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM75DSA120 is a 1200V ,

75 Ampere Intellimod™ Intelligent

Power Module. Type Current Rating V CES Amperes Volts (x 10) PM 75 120 Dimensions Inches Millimeters A 4.33 110.0 B 3.66 ±0.010 93.0 ±0.25 C 1.77 45.0 D 1.34 34.0 F 1.02 26.0 G 0.98 25.0 H 0.702 17.84 J 0.55 14.0 K 0.51 13.0 Dimensions Inches Millimeters L 0.47 12.0 M 0.33 8.5 N 0.28 7.0 P 0.230 5.84 Q 0.22 Dia. Dia. 5.5 R M5 Metric M5 S 0.100 2.54 T 0.08 Dia. Dia. 2.0 U 0.08 2.0 N J FE K H 0.64 MM SQ. PIN (10 TYP.) SNR VNC FNO VN1 CN1 VP1 SPR CP1 VPC FPO N SIDE P SIDE SINK SENS OUT2 OUT1 GND TEMP C2E1 IN VCC VNC SR FO CN1 SNR FNO VN1 SINK SENS OUT2 OUT1 GND TEMPVCC FO SR IN VP1 FPO SPR CP1 VPC L U M GGG B A DC P S S S S P N C2E1 E2 C1 213 4 5 2345 T - DIA. (4 TYP.) Q - DIA. (2 TYP.) R - M5 THD. (3 TYP.)

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM75DSA120 Units Power Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature T C -20 to 100 °C Mounting Torque, M5 Mounting Screws — 17 in-lb Mounting Torque, M5 Main Terminal Screws — 17 in-lb Module Weight (T ypical) — 340 Grams Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part) V CC(prot.) 800 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V RMS 2500 Volts Control Sector Supply Voltage Applied between (VP1-VPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (CP1-VPC , CN1 -VNC )V CIN 10 Volts Fault Output Supply Voltage (Applied between Fpo-Vpc and Fno-Vnc)V FO 20 Volts Fault Output Current I FO 20 mA IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 5V) V CES 1200 Volts Collector Current, ± IC 75 Amperes Peak Collector Current, ± ICP 150 Amperes Supply Voltage (Applied between C1 - E2) V CC 900 Volts Supply Voltage, Surge (Applied between C1 - E2) V CC(surge) 1000 Volts Collector Dissipation P C 460 Watts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part OC -20 °C ≤ T ≤ 125°C 105 170 — Amperes Short Circuit Trip Level Inverter Part SC -20 °C ≤ T ≤ 125°C 150 250 — Amperes Over Current Delay Time t off(OC) VD = 15V — 5 — µS Over Temperature Protection OT Trip Level 100 110 120 °C OT R Reset Level 85 95 105 °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts UV R Reset Level — 12.5 — Volts Supply Voltage V D Applied between VP1-VPC , VN1 -VNC 13.5 15 16.5 Volts Circuit Current I D VD = 15V, VCIN = 5V, VN1 -VNC —1 32 0 m A VD = 15V, VCIN = 5V, VXP1 -VXPC —1 32 0 m A Input ON Threshold Voltage V CIN(on) Applied between 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) C P1-VPC , CN1 -VNC 1.7 2.0 2.3 Volts PWM Input Frequency f PWM 3-B Sinusoidal — 15 20 kHz Fault Output Current I FO(H) VD = 15V, VFO = 15V — — 0.01 mA IFO(L) VD = 15V, VFO = 15V — 10 15 mA Minimum Fault Output Pulse Width t FO VD = 15V 1.0 1.8 — mS SXR Terminal Output Voltage V SXR Tj ≤125°C, Rin = 6.8 kV (SPR , SNR ) 4.5 5.1 5.6 Volts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CEX VCE = VCEX , Tj = 25°C— — 1 m A VCE = VCEX , Tj = 125°C— — 1 0 m A Diode Forward Voltage V FM -IC = 75A, VD = 15V, VCIN = 5V — 2.5 3.5 Volts Collector-Emitter Saturation Voltage V CE(sat) VD = 15V, VCIN = 0V, IC = 75A — 2.3 3.2 Volts VD = 15V, VCIN = 0V, IC = 75A, — 2.1 2.9 Volts Tj = 125°C Inductive Load Switching Times t on 0.5 1.4 2.5 µS trr VD = 15V, VCIN = 0 ~ 5V — 0.2 0.4 µS tC(on) VCC = 600V, IC = 75A — 0.4 1.0 µS toff Tj = 125°C — 2.5 3.5 µS tC(off) — 0.6 1.1 µS Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT — — 0.27 °C/Watt R th(j-c)D Each FWDi — — 0.51 °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module — — 0.060 °C/Watt Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across C1-E2 Terminals 0 ~ 800 Volts VD Applied between VP1-VPC , VN1 -VNC 15 ± 1.5 Volts Input ON Voltage V CIN(on) Applied between 0 ~ 0.8 Volts Input OFF Voltage V CIN(off) C P1-VPC , CN1 -VNC 4.0 ~ VSXR Volts PWM Input Frequency f PWM Using Application Circuit 5 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 3.5 µS

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT, I C , (AMPERES) SATURATION VOLTAGE V CE(sat), (VOLTS) 0 50 100 150 150 150 VD = 15V Tj = 25oC Tj = 125oC 0.5 1.0 1.5 2.0 2.5 COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) 12 14 16 18 20 VCIN = 0V Tj = 25oC Tj = 125oC IC = 75A 3.0 0 012 OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER VOLTAGE, V CE , (VOLTS) COLLECTOR CURRENT, I C , (AMPERES) 100 125 150 VD = 17V Tj = 25oC VCIN = 0V 100 101 102 10-1 SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 100 101 toff VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES)COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) tc(on) 100 101 tc(off) VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 101 102 10-2 EMITTER CURRENT, I E, (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) 10-1 100 VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 REVERSE RECOVERY CURRENT, I rr, (AMPERES) 101 102 Irr trr 0.4 2.8 100 DIODE FORWARD VOLTAGE, V F, (VOLTS) DIODE FORWARD CURRENT, -I F, (AMPERES) DIODE FORWARD CHARACTERISITCS 101 103 0.8 102 1.2 1.6 2.0 2.4 Tj = 25oC Tj = 125oC VD = 15V 100 120 140 OVER CURRENT TRIP LEVEL VS. SUPPLY VOLTAGE (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) OVER CURRENT TRIP LEVEL % (NORMALIZED) 12 14 16 18 20 Tj = 25oC 100 120 140 OVER CURRENT TRIP LEVEL VS. TEMPERATURE (TYPICAL) JUNCTION TEMPERATURE, T j, (oC) OVER CURRENT TRIP LEVEL % (NORMALIZED) -50 0 50 100 150 VD = 15V

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 100 120 140 FAULT OUTPUT PULSE WIDTH VS. TEMPERATURE (TYPICAL) JUNCTION TEMPERATURE, T j, (oC) FAULT OUTPUT PULSE WIDTH % (NORMALIZED) -50 0 50 100 150 VD = 15V CONTROL SUPPLY VOLTAGE TRIP-RESET LEVEL TEMPERATURE DEPENDENCY (TYPICAL) JUNCTION TEMPERATURE, T j, (oC) UV TRIP-RESET LEVEL, UV t, UVr, (VOLTS) -50 150 05 0 100 UV t UV r TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)Q = 0.27oC/W 10-210-3 TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)D = 0.51oC/W 10-210-3