PM75B4L1C060

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com Photo Voltaic IPM H-Bridge

75 Amperes/600 Volts

103/11 Rev. 0 Description: Powerex Intellimod™ Photo Voltaic Intelligent Power Modules are isolated base modules designed for single phase power switching applications. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: £ Complete Output Power Circuit £ Gate Drive Circuit £ Protection Logic – Short Circuit – Over Temperature Using On-chip Temperature Sensing – Under Voltage £ Low Loss Using Full Gate CSTBT IGBT Chip Applications: £ PV Inverters £ PV UPS £ PV Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM75B4L1C060 is a 600V, 75 Ampere PV-IPM. Type Current Rating VCES Amperes Volts (x 10) PM 75 60 Outline Drawing and Circuit Diagram A D E F F F F G G G G GG G GG G GG G B C G N P M QK J LL L L LF T U V C S (19 TYP .) R H (2 TYP .) 1 5 9 13 B P N U V W 19 FO 17 VN

14 VN1

8 VVP1

2 UFO

6 VFO

5 VVPC

1 VUPC

4 VUP1

13 VNC

1 .5k 1 .5k1 .5k VWNB VCC SI GND GND OUT FO IN OT UNFO VNC VN1 VN NC NCNC NC VVPC VP VFO VVP1 VUPC UP UFO VUP1 Dim. Inches Millimeters A 3.54 90.0 B 1 .97 50.0 C 0.98 25.0 D 3.15 80.0 E 0.20 5.0 F 0.39 10.0 G 0.08 2.0 H 0.17 Dia. 4.3 Dia. J 0.81 20.5 K 0.91 23.0 Dim. Inches Millimeters L 0.47 12.0 M 0.012 0.3 N 0.57 14.6 P 0.26 6.7 Q 0.02 0.5 R 0.56 14.2 S 0.02 Sq. 0.5 Sq. T 0.08 2.0 U 0.51 13.0 V 0.65 16.5

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com 03/11 Rev. 0 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM75B4L1C060 Units Power Device Junction Temperature Tj -20 to 150 °C Storage Temperature Tstg -40 to 125 °C Mounting Torque, M4 Mounting Screws (Typical) — 15 in-lb Module Weight (Typical) — 135 Grams Supply Voltage, Surge (Applied between P-N) VCC(surge) 500 Volts Operation of Short Circuit Protections VCC(prot.) 450 Volts (Applied between P-N, VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C Start) Isolation Voltage (60Hz, Sinusoidal, RMS, Charged Part to Base, AC 1 Minute) VISO 2500 Volts Inverter Part Collector-Emitter Voltage (VD = 15V, VCIN = 15V) VCES 600 Volts Collector Current (TC = 25°C) IC 75 Amperes Collector Current (Pulse) ICRM 150 Amperes Total Power Dissipation (TC = 25°C) Ptot 201 Watts Emitter Current (TC = 25°C, FWDi Current) IE 75 Amperes Emitter Current (Pulse, FWDi Current) IERM 150 Amperes Control Part Supply Voltage (Applied between VUP1-VUPC, VVP1-VVPC, VN1-VNC) V D 20 Volts Input Voltage (Applied between UP-VUPC, VP-VVPC, UN- VN- WN-Br-VNC) V CIN 20 Volts Fault Output Supply Voltage VFO 20 Volts (Applied between UFO-VUPC, VFO-VVPC, FO-VNC) Fault Output Supply Current (Sink Current at UFO, VFO, FO Terminals) I FO 20 mA

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com 03/11 Rev. 0 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Inverter Part Collector-Emitter Saturation Voltage V CE(sat) V D = 15V, IC = 75A, VCIN = 0V, — 2.2 2.7 Volts Pulsed, Tj = 25°C V D = 15V, IC = 75A, VCIN = 0V, — 2.2 2.7 Volts Pulsed, Tj = 125°C Emitter-Collector Voltage VEC I E = 75A, VD = 15V, VCIN = 15V — 2.4 3.3 Volts Switching Times ton 0.1 0.5 1 .2 µs t rr V D = 15V, VCIN = 0 ↔ 15V — 0.1 0.2 µs t C(on) V CC = 300V, IC = 75A, — 0.15 0.3 µs t off Tj = 125°C, Inductive Load — 1 .1 2.0 µs t C(off) — 0.2 0.4 µs Collector-Emitter Cutoff Current ICES V CE = VCES, VD = 15V, VCIN = 15V, Tj = 25°C — — 1 .0 mA V CE = VCES, VD = 15V, — — 10 mA VCIN = 15V, Tj = 125°C Control Part Circuit Current ID V D = 15V, VCIN = 15V, VN1-VNC — 6.5 12 mA V D = 15V, VCIN = 15V, V*P1-V*PC — 1 .6 4 mA Input ON Threshold Voltage Vth(on) Applied between UP-VUPC, 1 .2 1 .5 1 .8 Volts Input OFF Threshold Voltage Vth(off) V P-VVPC, UN- VN- WN-Br-VNC 1 .7 2.0 2.3 Volts Short Circuit Trip Level SC -20°C ≤ Tj ≤ 125°C, VD = 15V 112 — — Amperes Short Circuit Current Delay Time toff(SC) V D = 15V — 0.2 — µs Over Temperature Protection OT Trip Level 135 — — °C (Detect Temperature of IGBT) OT(hys) Hysteresis — 20 — °C Supply Circuit Under-voltage Protection UV t Trip Level 11 .5 12.0 12.5 Volts (-20°C ≤ Tj ≤ 125°C) UVr Reset Level — 12.5 — Volts Fault Output Current IFO(H) V D = 15V, VFO = 15V — — 0.01 mA I FO(L) V D = 15V, VFO = 15V — 10 15 mA Fault Output Pulse Width*2 t FO V D = 15V 1 .0 1 .8 — ms *2 Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it. Fault output of SC protection given pulse. Fault output of OT, UV protection given pulse while over trip level.

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com 03/11 Rev. 0 Thermal Characteristics, Tj = 25°C unless otherwise specified Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Inverter IGBT (Per 1 Element)* 1 — — 0.62 °C/Watt R th(j-c)D Inverter FWDi (Per 1 Element)* 1 — — 1 .06 °C/Watt Contact Thermal Resistance Rth(c-f) Case to Fin (Per 1 Element)*1, — 0.060 — °C/Watt Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Condition Value Units Inverter Supply Voltage VCC Applied across P-N Terminals ≤450 Volts Control Supply Voltage*3 V D Applied between VUP1-VUPC, 15.0 ± 1 .5 Volts V VP1-VVPC, VN1-VNC Input ON Voltage VCIN(on) Applied between UP-VUPC, ≤0.8 Volts Input OFF Voltage VCIN(off) V P-VVPC, UN- VN- WN-Br-VNC ≥9.0 Volts PWM Input Frequency fPWM Using Application Circuit Input Signal of IPM, ≤20 kHz 3-Phase Sinusoidal PWM VVVF Inverter Arm Shoot-through Blocking Time tDEAD For IPMs Each Input Signals ≥2.0 µs *1 When using this value, Rth(s-a) should be measured just under the chips. *3 With ripple satisfying the following conditions: dv/dt swing ≤5V/µs ; variation ≤2V peak-to-peak.