PM50CSD120 POWEREX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Three Phase IGBT Inverter Output
50 Amperes/1200 Volts
Description: Pow erex Intellimod™ Intelligent Pow er Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: □ Complete Output Power Circuit □ Gate Drive Circuit □ Protection Logic – Short Circuit –O ver Current –O ver Temperature – Under Voltage □ Low Loss Using 4th Generation IGBT Chip Applications: □ Inverters □ UPS □ Motion/Servo Control □ Pow er Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM50CSD120 is a 1200V,
50 Ampere Intellimod™ Intelligent
Pow er Module. Type Current Rating V CES Amperes Volts (x 10) PM 50 120 Outline Drawing and Circuit Diagram Dimensions Inches Millimeters F 2.62 66.44 G 1.28 32.6 H 1.24 31.6 J 1.02 26.0 K 0.94 24.0 M 0.79 20.0 N 0.76 19.4 P 0.18 4.5 Q 0.10 2.54 Dimensions Inches Millimeters R 0.67 17.02 S 0.67 17.02 T 0.52 13.2 U 0.39 10.0 V 0.16 4.0 W 0.02 0.5 Y 0.24 Rad. Rad. 6.0 Z 0.22 Dia. Dia.5.5 AA M5 M5 AB 0.13 3.22 AC 0.06 1.6 AG 0.020.01 0.5 ±0.3 AH 0.47 12.0 S A AH U Z (4 PLACES) F AB P Q (2 PLACES) AC L B M M AD AG J J E U U U R A N G H V C T V V V V V V V 10. 11. 12. 13. 14. 15. 16. U U VV W W WPC UPI VPI WPI NC NI P N P P N N UPC FO VVPC 78 9 11 13 151234 56 N VW U BP 17. 18. 19. NC WF O OVF OUF AA - THD AD 12 14 16 18 17 19 (19 TYP.) Y (4 PLACES) W SQ. PIN VV CC SI GND GND OUT UPI V U FO UP UPC FO IN V CC SI GND GND OUT FO IN V CC SI GND GND OUT FO IN V V FO V V FO VPI V VP VPC WPI W WP WPC V CC SI GND GND OUT FO IN V CC SI GND GND OUT FO IN U N V CC SI GND GND OUT FO IN V V W NV NI N NC TEMP NC FO PUVWNNC (6 PLACES)
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM50CSD120 Units Pow er Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature* TC -20 to 100 °C Mounting Torque, M5 Mounting Screws — 31 in-lb Mounting Torque, M5 Main Terminal Screws — 31 in-lb Module Weight (Typical) — 560 Grams Supply Voltage Protected by OC and SC V CC(prot.) 800 Volts (VD = 13.5 - 16.5V, Inverter Part) Tj = 125°C Start Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V ISO 2500 Volts IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) V CES 1200 Volts Collector Current, ± (TC = 25°C) I C 50 Amperes Peak Collector Current, ± (TC = 25°C) I CP 100 Amperes Supply Voltage (Applied between P - N) V CC 800 Volts Supply Voltage, Surge (Applied between P - N) V CC(surge) 1000 Volts Collector Dissipation (TC = 25°C) P C 328 Watts Control Sector Supply Voltage Applied between (VUP1 -VUPC , VVP1 -VVPC , VWP1 -VWPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (UP-VUPC , VP-VVPC , WP-VWPC , UN , VN , WN -VNC )V CIN 20 Volts Fault Output Supply Voltage Applied between V FO 20 Volts (UFO -VUPC , VFO -VVPC , WFO -VWPC , FO -VNC ) Fault Output Current (UFO , VFO , WFO , FO )I FO 20 mA Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CES VCE = VCES , Tj = 25°C, VD = 15V — — 1.0 mA VCE = VCES , Tj = 125°C, VD = 15V — — 10 mA Diode Forward Voltage V EC -IC = 50A, VD = 15V, VCIN = 15V — 2.5 3.5 Volts Collector-Emitter V CE(sat) VD = 15V, VCIN = 0V, IC = 50A, Pulsed, Tj = 25°C— 2.4 3.2 Volts Saturation Voltage V D = 15V, VCIN = 0V, IC = 50A,Pulsed, Tj = 125°C— 2.1 2.8 Volts Inductive Load Switching Times t on 0.5 1.0 2.5 µS trr VD = 15V, VCIN = 0 ~ 15V — 0.15 0.3 µS tC(on) VCC = 600V, IC = 50A — 0.4 1.0 µS toff Tj = 125°C, Inductive Load — 2.5 3.5 µS tC(off) — 0.7 1.2 µS *TC Measure Point 63MM TC
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level OC T j = 25°C9 3 157 — Amperes (VD = 15V) T j = 125°C5 9— — Amperes Short Circuit Trip Level SC -20 °C ≤ Tj ≤ 125°C, VD = 15V — 183 — Amperes Over Current Delay Time t off(OC) VD = 15V — 10 — µS Over Temperature Protection (VD = 15V) OT Trip Level 111 118 125 °C (Lower Arm) OT R Reset Level — 100 — °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts (-20 ≤ Tj ≤ 125°C) UV R Reset Level — 12.5 — Volts Circuit Current I D VD = 15V, VCIN = 15V, VN1 -VNC —4 05 5 m A VD = 15V, VCIN = 15V, VXP1 -VXPC —1 31 8 m A Input ON Threshold Voltage V CIN(on) Applied between UP-VUPC , VP-VVPC , 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) W P-VWPC , UN , VN , WN -VNC 1.7 2.0 2.3 Volts Fault Output Current* I FO(H) VD = 15V, VCIN = 15V — — 0.01 mA IFO(L) VD = 15V, VCIN = 15V — 10 15 mA Minimum Fault Output Pulse Width* t FO VD = 15V 1.0 1.8 — mS *Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower arm device operate to protect it. Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT — — 0.38 °C/Watt Inverter Part R th(j-c)F Each FWDi — — 0.70 °C/Watt R th(j-c´)Q Each IGBT — — 0.23 † °C/Watt R th(j-c´)F Each FWDi — — 0.36 † °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module, — — 0.027 °C/Watt Thermal Grease Applied TC measured point is just under the chips. †If you use this value, Rth(f-a) should be measured just under the chips. Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across P-N Terminals 0 ~ 800 Volts Control Supply Voltage* V D Applied between VUP1 -VUPC , 15 ± 1.5 Volts VN1 -VNC , VVP1 -VVPC , VWP1 -VWPC Input ON Voltage V CIN(on) Applied between UP-VUPC , VP-VVPC ,0 ~ 0.8 Volts Input OFF Voltage V CIN(off) W P-VWPC , UN, VN , WN -VNC 4.0 ~ VD Volts PWM Input Frequency f PWM Using Application Circuit 0 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 3.0 µS ***With ripple satisfying the following conditions: dv/dt ≤ ±5v/µs, Variation ≤ 2V peak to peak.
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngw ood, Pennsylvania 15697-1800 (724) 925-7272 1.0 2.0 3.0 SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT, I C , (AMPERES) SATURATION VOLTAGE, V CE(sat), (VOLTS) 06 0 20 40 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC 2.5 1.5 0.5 100 101 102 DIODE FORWARD CHARACTERISTICS (TYPICAL) DIODE FORWARD VOLTAGE, V EC , (VOLTS) DIODE CURRENT, -IC , (AMPERES) Tj = 25oC Tj = 125oC VD = 15V 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 100 101 toff VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) tc(on) 100 101 tc(off) tc(off) VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 101 102 10-2 COLLECTOR CURRENT, -I C , (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) 10-1 100 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25oC Tj = 125oC 100 REVERSE RECOVERY CURRENT, I rr, (AMPERES) 101 102 trr Irr 100 CIRCUIT CURRENT VS. CARRIER FREQUENCY CARRIER FREQUENCY, f C , (kHz) CIRCUIT CURRENT, ID , (mA) 51 0 1 5 2 0 2 5 Tj = 25oC N-SIDE P-SIDE20 INDUCTIVE LOAD 100 101 102 10-1 SWITCHING LOSS, E SW , (m)J/PULSE) SWITCHING LOSS CHARACTERISTICS (TYPICAL) 100 101 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25oC Tj = 125oC Esw(off) Esw(off) Esw(on) Esw(on) TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT & FWDi - INVERTER PART) 101 10-1 100 101 100 10-1 10-2 10-3 STANDARD VALUE R th(j-c)Q = 0.38oC/W (IGBT) R th(j-c)F = 0.70oC/W (FWDi) SINGLE PULSE 10-210-3 COLLECTOR CURRENT, I C , (AMPERES) INDUCTIVE LOAD 1.0 2.0 3.0 COLLECTOR-EMITTER SATURATION VOLTAGE (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) SATURATION VOLTAGE, V CE(sat), (VOLTS) 1201 8 13 14 15 16 17 IC = 50A Tj = 25oC Tj = 125oC 1.5 2.5 0.5