PM50CSD060

PM50CSD060 POWEREX | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Three Phase IGBT Inverter Output

50 Amperes/600 Volts

Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: □ Complete Output Power Circuit □ Gate Drive Circuit □ Protection Logic – Short Circuit – Over Current – Over Temperature – Under Voltage □ Low Loss Using 4th Generation IGBT Chip Applications: □ Inverters □ UPS □ Motion/Servo Control □ Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM50CSD060 is a 600V,

50 Ampere Intellimod™ Intelligent

Power Module. Type Current Rating V CES Amperes Volts (x 10) PM 50 60 Dimensions Inches Millimeters D 3.27 83.0 F 2.44 62.0 G 1.28 32.6 H 1.24 31.6 J 1.02 26.0 K 0.94 24.0 M 0.79 20.0 N 0.76 19.4 P 0.75 19.0 Q 0.708 17.98 R 0.670 17.02 Dimensions Inches Millimeters S 0.67 17.0 T 0.52 13.2 U 0.39 10.0 V 0.28 7.0 W 0.30 7.5 X 0.24 6.0 Y 0.24 Rad. Rad. 6.0 Z 0.22 Dia. Dia. 5.5 AA Metric M5 M5 AB 0.127 3.22 AC 0.10 2.6 AE 0.07 1.8 AF 0.06 1.6 Outline Drawing and Circuit Diagram T AC V V V V V V V 10. 11. 12. 13. 14. 15. 16. U U VV W W WPC UPI VPI WPI NC NI P N P P N N UPC FO V VPC 17. 18. 19. NC WF O OVF OUF B S M M AD AG AG K J J TC Measured Point E U U UAB Q AB R F A U D X P X W W C 78 9 11 13 151234 56 N VW U BP AA - THD (6 TYP.) Z - DIA. (4 TYP.) AD (15 TYP.) 12 14 16 18 17 19 Y (4 TYP.) N AE G H LAFV 2.54 MM DIA. (2 TYP.) 0.5 MM SQ. PIN (19 TYP.) VV CC S I GND GND OUT UPI V U FO UP UPC F O IN V CC S I GND GND OUT F O IN V CC S I GND GND OUT F O IN V V FO V V FO VPI V VP VPC WPI W WP WPC V CC S I GND GND OUT F O IN V CC S I GND GND OUT F O IN U N V CC S I GND GND OUT F O IN V V W NV NI N NC TEMP NC FO PUVWNNC

Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM50CSD060 Units Power Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature T C -20 to 100 °C Mounting Torque, M5 Mounting Screws — 31 in-lb Mounting Torque, M5 Main Terminal Screws — 31 in-lb Module Weight (Typical) — 560 Grams Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V , Inverter Part) Tj = 125°CV CC(prot.) 400 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V ISO 2500 Volts IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) V CES 600 Volts Collector Current, ± (TC = 25°C) I C 50 Amperes Peak Collector Current, ± (TC = 25°C) I CP 100 Amperes Supply Voltage (Applied between P - N) V CC 400 Volts Supply Voltage, Surge (Applied between P - N) V CC(surge) 500 Volts Collector Dissipation (TC = 25°C) P C 125 Watts Control Sector Supply Voltage Applied between (VUP1 -VUPC , VVP1 -VVPC , VWP1 -VWPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (UP-VUPC , VP-VVPC , WP-VWPC , UN - VN - WN -VNC )V CIN 20 Volts Fault Output Supply Voltage (Applied between FO and VC )V FO 20 Volts Fault Output Current (UFO , VFO , WFO , FO )I FO 20 mA Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CES VCE = VCES , Tj = 25°C, —— 1.0 mA VD = 15V, VCIN = 15V VCE = VCES , Tj = 125°C, —— 10 mA VD = 15V, VCIN = 15V Diode Forward Voltage V EC -IC = 50A, VD = 15V, VCIN = 15V — 2.2 3.3 Volts Collector-Emitter Saturation Voltage V CE(sat) VD = 15V, VCIN = 0V, IC = 50A, — 1.70 2.3 Volts Tj = 25°C VD = 15V, VCIN = 0V, IC = 50A, — 1.70 2.3 Volts Tj = 125°C Inductive Load Switching Times t on 0.8 1.2 2.4 µS trr VD = 15V, VCIN = 0 ~ 15V — 0.15 0.3 µS tC(on) VCC = 300V, IC = 50A — 0.4 1.0 µS toff Tj = 125°C — 2.4 3.3 µS tC(off) — 0.6 1.2 µS

Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part OC T j = -20°C —— 220 Amperes (VD = 15V) T j = 25°C 109 128 180 Amperes Tj = 125°C6 5 —— Amperes Short Circuit Trip Level Inverter Part SC -20 °C ≤ Tj ≤ 125°C, VD = 15V — 132 — Amperes Over Current Delay Time t off(OC) VD = 15V — 10 — µS Over Temperature Protection (VD = 15V) OT Trip Level 111 118 125 °C (Lower Arm) OT R Reset Level — 100 — °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts (-20 ≤ Tj ≤ 125°C) UV R Reset Level — 12.5 — Volts Circuit Current I D VD = 15V, VCIN = 15V, VN1 -VNC — 40 55 mA VD = 15V, VCIN = 15V, VXP1 -VXPC — 13 18 mA Input ON Threshold Voltage V CIN(on) Applied between 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) UP, VP, WP, UN , VN , WN -VNC 1.7 2.0 2.3 Volts Fault Output Current* I FO(H) VD = 15V, VFO = 15V —— 0.01 mA IFO(L) VD = 15V, VFO = 15V — 10 15 mA Minimum Fault Output Pulse Width* t FO VD = 15V 1.0 1.8 — mS *Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower devide operate to protect it. Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT —— 1.00 °C/Watt R th(j-c)F Each FWDi —— 2.50 °C/Watt R th(j-c´)Q Each IGBT —— 0.82† °C/Watt R th(j-c´)F Each FWDi —— 1.51† °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module, —— 0.027 °C/Watt Thermal Grease Applied TC measured point is just under chip. † If you use this value, Rth(f-a) should be measured just under the chips. Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across P-N Terminals 0 ~ 400 Volts Control Supply Voltage* V D Applied between VUP1 -VUPC , 15 ± 1.5 Volts VN1 -VNC , VVP1 -VVPC , VWP1 -VWPC Input ON Voltage V CIN(on) Applied between 0 ~ 0.8 Volts Input OFF Voltage V CIN(off) U P, VP, WP, UN, VN, W N -VNC 4.0 ~ VD Volts PWM Input Frequency f PWM Using Application Circuit 0 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 2.5 µS *** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak.

Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 0.5 1.0 2.0 1.5 SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) (INVERTER PART) COLLECTOR CURRENT, I C , (AMPERES) SATURATION VOLTAGE, V CE(sat), (VOLTS) 01 0 5 0 20 30 40 VD = 15V Tj = 25oC Tj = 125oC VCIN = 0V 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 100 101 toff 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) tc(on) 100 101 tc(off) VCC = 300V VD = 15V Tj = 25oC Tj = 125oC 100 101 102 10-2 COLLECTOR CURRENT, I C , (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) 10-1 100 VCC = 300V VD = 15V Tj = 25oC Tj = 125oC 100 REVERSE RECOVERY CURRENT, I rr, (AMPERES) 101 102 Irr trr 0 1.0 2.5 100 DIODE FORWARD VOLTAGE, V EC , (VOLTS) DIODE CURRENT, -IC , (AMPERES) DIODE FORWARD CHARACTERISTICS (INVERTER PART) 101 102 0.5 1.5 2.0 Tj = 25oC Tj = 125oC VD = 15V INDUCTIVE LOAD VCC = 300V VD = 15V Tj = 25oC Tj = 125oC INDUCTIVE LOAD 100 101 102 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING LOSS, E SW (mJ/PULSE) 100 101 CONDITIONS: HALF-BRIDGE INDUCTIVE LOAD SWITCHING OPERATION V CC = 300V VGE = ±15V Esw(on) Esw(off) Tj = 25oC Tj = 125oCINDUCTIVE LOAD TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 101 10-1 100 101 100 10-1 10-2 10-3 STANDARD VALUE R th(j-c)Q = 1.00oC/W SINGLE PULSE 10-210-3 TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 101 10-1 100 101 100 10-1 10-2 10-3 10-210-3 SWITCHING LOSS CHARACTERISTICS STANDARD VALUE R th(j-c)Q = 2.50oC/W SINGLE PULSE