PM300DSA060

PM300DSA060 POWEREX | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Single Phase IGBT Inverter Output

300 Amperes/600 Volts

Outline Drawing and Circuit Diagram 623 Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free wheel-diode power devices. Features: h Complete Output Power Circuit h Gate Drive Circuit h Protection Logic – Short Circuit – Over Current – Over Temperature – Under Voltage Applications: h Inverters h UPS h Motion/Servo Control h Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM300DSA060 is a 600V ,

300 Ampere Intellimod™ Intelligent

Power Module. Type Current Rating V CES Amperes Volts (x 10) PM 300 60 Dimensions Inches Millimeters A 4.33 110.0 B 3.66 ±0.010 93.0 ±0.25 C 2.20 56.0 D 2.01 51.0 F 1.02 26.0 G 0.98 25.0 H 0.90 23.0 J 0.85 21.5 Dimensions Inches Millimeters K 0.55 14.0 L 0.51 13.0 M 0.47 12.0 N 0.33 8.5 P 0.28 7.0 Q 0.22 Dia. Dia. 5.5 R M5 Metric M5 S 0.100 2.54 T 0.08 Dia. Dia. 2.0 K FE SNR VNC FNO VN1 CN1 VP1 SPR CP1 VPC FPO N SIDE P SIDE L P 0.64 MM SQ. PIN (10 TYP.) M DH GG B A N J C N S (8 TYP.)C2E1 E2 C1 21 345 T - DIA. (2 TYP.) Q - DIA. (2 TYP.) R - THD. (3 TYP.) P 213 4 5 SINK SENS OUT2 OUT1 GND TEMPVCC FO SR IN VN1 FNO SNR CN1 VNC C2E1 SINK SENS OUT2 OUT1 GND TEMPVCC FO SR IN C1VP1 FPO SPR CP1 VPC

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM300DSA060 Units Power Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature T C -20 to 100 °C Mounting Torque, M5 Mounting Screws — 17 in-lb Mounting Torque, M5 Main Terminal Screws — 17 in-lb Module Weight (Typical) — 430 Grams Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V , Inverter Part) V CC(prot.) 400 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V RMS 2500 Volts Control Sector Supply Voltage Applied between (VP1-VPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (CP1-VPC , CN1 -VNC )V CIN 10 Volts Fault Output Supply Voltage (Applied between Fpo-Vpc and Fno-Vnc)V FO 20 Volts Fault Output Current I FO 20 mA IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 5V) V CES 600 Volts Collector Current, ± IC 300 Amperes Peak Collector Current, ± ICP 600 Amperes Supply Voltage (Applied between C1 - E2) V CC 450 Volts Supply Voltage, Surge (Applied between C1 - E2) V CC(surge) 500 Volts Collector Dissipation P C 960 Watts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part OC -20 °C ≤ T ≤ 125°C 390 540 — Amperes Short Circuit Trip Level Inverter Part SC -20 °C ≤ T ≤ 125°C 540 760 — Amperes Over Current Delay Time t off(OC) VD = 15V — 5 — µS Over Temperature Protection OT Trip Level 100 110 120 °C OT R Reset Level 85 95 105 °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts UV R Reset Level — 12.5 — Volts Supply Voltage V D Applied between VP1-VPC , VN1 -VNC 13.5 15 16.5 Volts Circuit Current I D VD = 15V, VCIN = 5V, VN1 -VNC —1 92 6 m A VD = 15V, VCIN = 5V, VXP1 -VXPC —1 92 6 m A Input ON Threshold Voltage V CIN(on) Applied between 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) C P1-VPC , CN1 -VNC 1.7 2.0 2.3 Volts PWM Input Frequency f PWM 3-B Sinusoidal — 15 20 kHz Fault Output Current I FO(H) VD = 15V, VFO = 15V — — 0.01 mA IFO(L) VD = 15V, VFO = 15V — 10 15 mA Minimum Fault Output Pulse Width t FO VD = 15V 1.0 1.8 — mS SXR Terminal Output Voltage V SXR Tj ≤125°C, Rin = 6.8 kV (SPR , SNR ) 4.5 5.1 5.6 Volts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CEX VCE = VCEX , Tj = 25°C— — 1 m A VCE = VCEX , Tj = 125°C— — 1 0 m A Diode Forward Voltage V FM -IC = 300A, VD = 15V, VCIN = 5V — 1.9 2.8 Volts Collector-Emitter Saturation Voltage V CE(sat) VD = 15V, VCIN = 0V, IC = 300A — 1.8 2.6 Volts VD = 15V, VCIN = 0V, IC = 300A, — 1.9 2.7 Volts Tj = 125°C Inductive Load Switching Times t on 0.5 1.4 2.5 µS trr VD = 15V, VCIN = 0 ~ 5V — 0.15 0.3 µS tC(on) VCC = 300V, IC = 300A — 0.4 1.0 µS toff Tj = 125°C — 2.0 3.0 µS tC(off) — 0.5 1.0 µS Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT — — 0.13 °C/Watt R th(j-c)D Each FWDi — — 0.25 °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module — — 0.048 °C/Watt Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across C1-E2 Terminals 0 ~ 400 Volts VD Applied between VP1-VPC , VN1 -VNC 15 ± 1.5 Volts Input ON Voltage V CIN(on) Applied between 0 ~ 0.8 Volts Input OFF Voltage V CIN(off) C P1-VPC , CN1 -VNC 4.0 ~ VSXR Volts PWM nput Frequency f PWM Using Application Circuit 5 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 3.5 µS

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 101 102 103 10-1 100 101 toff VCC = 300V VD = 15V Tj = 25oC Tj = 125oC COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) 101 102 103 10-1 100 101 tc(off) tc(on) VCC = 300V VD = 15V Tj = 25oC Tj = 125oC EMITTER CURRENT, I E, (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) REVERSE RECOVERY CURRENT, I rr, (AMPERES) 101 102 103 10-2 10-1 100 101 102 103 VCC = 300V VD = 15V Tj = 25oC Tj = 125oC trr Irr DIODE FORWARD VOLTAGE, V F, (VOLTS) DIODE FORWARD CURRENT, I F, (AMPERES) DIODE FORWARD CHARACTERISTICS 100 101 102 103 Tj = 25oC Tj = 125oC VD = 15V SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT, I C , (AMPERES) SATURATION VOLTAGE V CE(sat), (VOLTS) 00 50 450 250 350 VD = 15V Tj = 25oC Tj = 125oC 150 COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) 12 14 16 18 20 IC = 300A Tj = 25oC Tj = 125oC 012 OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER VOLTAGE, V CE , (VOLTS) COLLECTOR CURRENT, I C , (AMPERES) 500 400 300 100 200 Tj = 25oC VD = 17V 100 120 OVER CURRENT TRIP LEVEL VS. SUPPLY VOLTAGE (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) OVER CURRENT TRIP LEVEL % (NORMALIZED) 13 15 17 19 21 TC = 25oC 100 120 140 OVER CURRENT TRIP LEVEL VS. TEMPERATURE (TYPICAL) JUNCTION TEMPERATURE, T C , (oC) OVER CURRENT TRIP LEVEL % (NORMALIZED) 0 40 80 120 160 VD = 15V

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 100 120 FAULT OUTPUT PULSE WIDTH VS. CASE TEMPERATURE (TYPICAL) CASE TEMPERATURE, T C , (oC) FAULT OUTPUT PULSE WIDTH % (NORMALIZED) 0 40 80 120 160 VD = 15V CONTROL SUPPLY VOLTAGE TRIP-RESET LEVEL TEMPERATURE DEPENDENCY (TYPICAL) JUNCTION TEMPERATURE, T C , (oC) UV TRIP-RESET LEVEL, UV, UVr, (VOLTS) 0 160 40 80 120 UV UV r TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)Q = 0.13oC/W 10-210-3 TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)D = 0.25oC/W 10-210-3