PM200DSA120

PM200DSA120 POWEREX | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Single Phase IGBT Inverter Output

200 Amperes/1200 Volts

Outline Drawing and Circuit Diagram 659 Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: h Complete Output Power Circuit h Gate Drive Circuit h Protection Logic – Short Circuit – Over Current – Over Temperature – Under Voltage Applications: h Inverters h UPS h Motion/Servo Control h Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM200DSA120 is a 1200V,

200 Ampere Intellimod™ Intelligent

Power Module. Type Current Rating V CES Amperes Volts (x 10) PM 200 120 Dimensions Inches Millimeters A 5.12 130.0 B 4.33 ±0.010 110.0 ±0.25 C 2.76 70.0 D 2.05 ±0.010 52.0 ±0.25 E 1.18 30.0 G 1.02 26.0 H 0.98 25.0 J 0.71 18.0 Dimensions Inches Millimeters K 0.55 14.0 L 0.51 13.0 M 0.28 7.0 N 0.26 Dia. Dia. 6.5 P M6 Metric M6 Q 0.14 3.5 R 0.100 2.54 S 0.08 Dia. Dia. 2.0 T 0.016 0.42 K SNR VNC FNO VN1 CN1 VP1 SPR CP1 VPC FPO N SIDE P SIDE GF M L 0.64 MM SQ. PIN (10 TYP.) HH C A Q J E B JD K T P NC2E1 E2 C1 213 4 5 2345 S - DIA. (4 TYP.) P - M6 THD. (3 TYP.) N - DIA. (4 TYP.) R (8 TYP.) SINK SENS OUT2 OUT1 GND TEMPVCC FO SR IN VN1 FNO SNR CN1 VNC C2E1 SINK SENS OUT2 OUT1 GND TEMPVCC FO SR IN C1VP1 FPO SPR CP1 VPC

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM200DSA120 Units Power Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature T C -20 to 100 °C Mounting Torque, M6 Mounting Screws — 26 in-lb Mounting Torque, M6 Main Terminal Screws — 26 in-lb Module Weight (Typical) — 630 Grams Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part) V CC(prot.) 800 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V RMS 2500 Volts Control Sector Supply Voltage Applied between (VP1-VPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (CP1-VPC , CN1 -VNC )V CIN 10 Volts Fault Output Supply Voltage (Applied between Fpo-Vpc and Fno-Vnc)V FO 20 Volts Fault Output Current I FO 20 mA IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 5V) V CES 1200 Volts Collector Current, ± IC 200 Amperes Peak Collector Current, ± ICP 400 Amperes Supply Voltage (Applied between C1 - E2) V CC 900 Volts Supply Voltage, Surge (Applied between C1 - E2) V CC(surge) 1000 Volts Collector Dissipation P C 1140 Watts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part OC -20 °C ≤ T ≤ 125°C 240 360 — Amperes Short Circuit Trip Level Inverter Part SC -20 °C ≤ T ≤ 125°C 320 540 — Amperes Over Current Delay Time t off(OC) VD = 15V — 5 — µS Over Temperature Protection OT Trip Level 100 110 120 °C OT R Reset Level 85 95 105 °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts UV R Reset Level — 12.5 — Volts Supply Voltage V D Applied between VP1-VPC , VN1 -VNC 13.5 15 16.5 Volts Circuit Current I D VD = 15V, VCIN = 5V, VN1 -VNC —2 33 0 m A VD = 15V, VCIN = 5V, VXP1 -VXPC —2 33 0 m A Input ON Threshold Voltage V CIN(on) Applied between 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) C P1-VPC , CN1 -VNC 1.7 2.0 2.3 Volts PWM Input Frequency f PWM 3-B Sinusoidal — 15 20 kHz Fault Output Current I FO(H) VD = 15V, VFO = 15V — — 0.01 mA IFO(L) VD = 15V, VFO = 15V — 10 15 mA Minimum Fault Output Pulse Width t FO VD = 15V 1.0 1.8 — mS SXR Terminal Output Voltage V SXR Tj ≤125°C, Rin = 6.8 kV (SPR , SNR ) 4.5 5.1 5.6 Volts

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CEX VCE = VCEX , Tj = 25°C— — 1 m A VCE = VCEX , Tj = 125°C— — 1 0 m A Diode Forward Voltage V FM -IC = 200A, VD = 15V, VCIN = 5V — 2.5 3.5 Volts Collector-Emitter Saturation Voltage V CE(sat) VD = 15V, VCIN = 0V, IC = 200A — 2.3 3.2 Volts VD = 15V, VCIN = 0V, IC = 200A, — 2.1 2.9 Volts Tj = 125°C Inductive Load Switching Times t on 0.5 1.4 2.5 µS trr VD = 15V, VCIN = 0 ~ 5V — 0.2 0.4 µS tC(on) VCC = 600V, IC = 200A — 0.4 1.0 µS toff Tj = 125°C — 2.0 3.5 µS tC(off) — 0.6 1.1 µS Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT — — 0.11 °C/Watt R th(j-c)D Each FWDi — — 0.18 °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module, — — 0.038 °C/Watt Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across C1-E2 Terminals 0 ~ 800 Volts VD Applied between VP1-VPC , VN1 -VNC 15 ± 1.5 Volts Input ON Voltage V CIN(on) Applied between 0 ~ 0.8 Volts Input OFF Voltage V CIN(off) C P1-VPC , CN1 -VNC 4.0 ~ VSXR Volts PWM Input Frequency f PWM Using Application Circuit 5 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 3.5 µS

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 12 14 SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) SATURATION VOLTAGE V CE(sat), (VOLTS) 16 20 22 IC = 200A Tj = 25oC Tj = 125oC 008 0 COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT, I C , (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) 240 320160 VD = 15V Tj = 25oC Tj = 125oC 012 OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER VOLTAGE, V CE(sat), (VOLTS) COLLECTOR CURRENT, I C , (AMPERES) 120 200 280 360 VD = 17V Tj = 25oC COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 101 102 103 10-1 100 101 toff VCC = 600V VD = 15V Tj = 25oC Tj = 125oC COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) 101 102 103 10-1 100 101 tc(off) tc(on) VCC = 600V VD = 15V Tj = 25oC Tj = 125oC EMITTER CURRENT, I E, (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) REVERSE RECOVERY CURRENT, I rr, (AMPERES) 101 102 103 10-2 10-1 100 101 102 103 VCC = 600V VD = 15V Tj = 25oC Tj = 125oC trr Irr 100 DIODE FORWARD VOLTAGE, V F, (VOLTS) DIODE FORWARD CURRENT, I F, (AMPERES) Tj = 25oC Tj = 125oC VD = 15V 101 102 103 DIODE FORWARD CHARACTERISTICS 100 120 OVER CURRENT TRIP LEVEL VS. SUPPLY VOLTAGE (TYPICAL) SUPPLY VOLTAGE, V D , (VOLTS) OVER CURRENT TRIP LEVEL % (NORMALIZED) 13 15 17 19 21 TC = 25oC 100 120 140 OVER CURRENT TRIP LEVEL VS. TEMPERATURE (TYPICAL) JUNCTION TEMPERATURE, T C , (oC) OVER CURRENT TRIP LEVEL % (NORMALIZED) 0 40 80 120 160 VD = 15V

Intellimod™ Module Single Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 100 120 140 FAULT OUTPUT PULSE WIDTH VS. TEMPERATURE (TYPICAL) JUNCTION TEMPERATURE, T C , (oC) FAULT OUTPUT PULSE WIDTH % (NORMALIZED) 0 40 80 120 160 VD = 15V CONTROL SUPPLY VOLTAGE TRIP-RESET LEVEL TEMPERATURE DEPENDENCY (TYPICAL) JUNCTION TEMPERATURE, T C , (oC) UV TRIP-RESET LEVEL, UV, UVr, (VOLTS) 0 160 40 80 120 UV UV r TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)Q = 0.11oC/W 10-210-3 TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 101 10-1 100 101 100 10-1 10-2 10-3 SINGLE PULSE STANDARD VALUE = R th(j-c)D = 0.18oC/W 10-210-3