PM150CSD120 POWEREX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272Intellimod™ Module Three Phase IGBT Inverter Output
150 Amperes/1200 Volts
Description: Pow erex Intellimod™ Intelligent Pow er Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: □ Complete Output Power Circuit □ Gate Drive Circuit □ Protection Logic – Short Circuit –O ver Current –O ver Temperature – Under Voltage □ Low Loss Using 4th Generation IGBT Chip Applications: □ Inverters □ UPS □ Motion/Servo Control □ Pow er Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM150CSD120 is a 1200V,
150 Ampere Intellimod™ Intelligent
Pow er Module. Type Current Rating V CES Amperes Volts (x 10) PM 150 120 Dimensions Inches Millimeters D 4.27 108.5 F 3.29 83.5 G 2.01 51.0 H 1.602 40.68 J 1.54 39.0 K 1.37 34.7 L 1.33 33.7 M 1.02 26.0 P 0.85 21.5 Q 0.79 20.0 R 0.780 19.82 Dimensions Inches Millimeters S 0.69 17.5 T 0.65 16.5 U 0.52 13.2 V 0.43 11.0 W 0.39 10.0 X 0.16 4.0 Y 0.285 7.25 Z 0.24 6.0 AA 0.22 Dia. Dia. 5.5 AB Metric M5 M5 AC 0.128 3.22 AD 0.10 2.6 AE 0.08 2.0 AF 0.07 1.8 AG 0.06 1.6 AH 0.02 0.5 Outline Drawing and Circuit Diagram V V V V V V V 10. 11. 12. 13. 14. 15. 16. U U VV W W WPC UPI VPI WPI NC NI P N P P N N UPC FO V VPC 17. 18. 19. NC OWF OVF OUF AC R B A YY CE V F W M M S Z D Z J Q Q T H AC W W W AH AH G N V B P WU Z Y Z Y AB - THD (6 TYP.) AA - DIA. (4 TYP.) 3 AE (15 TYP.) 4 5678 9 1 1 12 14 16 18 13 15 17 19 P AF AG X AD N L K U 2.54 MM DIA. (2 TYP.) 0.5 MM SQ. PIN (19 TYP.) VV CC S I GND GND OUT UPI V U FO UP UPC F O IN V CC S I GND GND OUT F O IN V CC S I GND GND OUT F O IN V V FO V V FO VPI V VP VPC WPI W WP WPC V CC S I GND GND OUT F O IN V CC S I GND GND OUT F O IN U N V CC S I GND GND OUT F O IN V V W NV NI N NC TEMP NC FO PUVWNNC
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol PM150CSD120 Units Pow er Device Junction Temperature T j -20 to 150 °C Storage Temperature T stg -40 to 125 °C Case Operating Temperature* TC -20 to 100 °C Mounting Torque, M5 Mounting Screws — 31 in-lb Mounting Torque, M5 Main Terminal Screws — 31 in-lb Module Weight (Typical) — 920 Grams Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part) Tj = 125°CV CC(prot.) 800 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal V ISO 2500 Volts IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) V CES 1200 Volts Collector Current, ± (TC = 25°C) I C 150 Amperes Peak Collector Current, ± (TC = 25°C) I CP 300 Amperes Supply Voltage (Applied between P - N) V CC 800 Volts Supply Voltage, Surge (Applied between P - N) V CC(surge) 1000 Volts Collector Dissipation (TC = 25°C) P C 781 Watts Control Sector Supply Voltage Applied between (VUP1 -VUPC , VVP1 -VVPC , VWP1 -VWPC , VN1 -VNC )V D 20 Volts Input Voltage Applied between (UP-VUPC , VP-VVPC , WP-VWPC , UN - VN - WN -VNC )V CIN 20 Volts Fault Output Supply Voltage (Applied between UFO -VUPC ,V FO 20 Volts VFO -VVPC , WFO -VWPC , FO -VNC ) Fault Output Current (UFO , VFO , WFO , FO )I FO 20 mA Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current ICES VCE = VCES , Tj = 25°C, VD = 15V, VCIN = 15V — — 1.0 mA VCE = VCES , Tj = 125°C, VD = 15V, VCIN = 15V — — 10 mA Diode Forward Voltage V EC -IC = 150A, VD = 15V, VCIN = 15V — 2.5 3.5 Volts Collector-Emitter V CE(sat) VD = 15V, VCIN = 0V, IC = 150A, Pulsed, Tj = 25°C— 2.4 3.2 Volts Saturation Voltage V D = 15V, VCIN = 0V, IC = 150A, Pulsed, Tj = 125°C— 2.1 2.8 Volts Inductive Load t on 0.5 1.0 2.5 µS Switching Times t rr VD = 15V, VCIN = 0 ~ 15V — 0.15 0.3 µS tC(on) VCC = 600V, IC = 150A — 0.4 1.0 µS toff Tj = 125°C, Inductive Load — 2.5 3.5 µS tC(off) — 0.7 1.2 µS *TC Measure Point 63MM TC N V B P WU 34 5678 9 1 1 12 14 16 18 13 15 17 19
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level OC T j = 25°C 282 410 — Amperes (VD = 15V) T j = 125°C 200 — — Amperes Short Circuit Trip Level SC -20 °C ≤ Tj ≤ 125°C, VD = 15V — 540 — Amperes Over Current Delay Time t off(OC) VD = 15V — 10 — µS Over Temperature Protection (VD = 15V) OT Trip Level 111 118 125 °C (Lower Arm) OT R Reset Level — 100 — °C Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts (-20 ≤ Tj ≤ 125°C) UV R Reset Level — 12.5 — Volts Circuit Current I D VD = 15V, VCIN = 15V, VN1 -VNC —4 56 2 m A VD = 15V, VCIN = 15V, VXP1 -VXPC —1 52 0 m A Input ON Threshold Voltage V CIN(on) Applied between UP-VUPC , VP-VVPC , 1.2 1.5 1.8 Volts Input OFF Threshold Voltage V CIN(off) W P-VWPC , UN , VN , WN -VNC 1.7 2.0 2.3 Volts Fault Output Current* I FO(H) VD = 15V, VCIN = 15V — — 0.01 mA IFO(L) VD = 15V, VCIN = 15V — 10 15 mA Minimum Fault Output Pulse Width* t FO VD = 15V 1.0 1.8 — mS *Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower devide operate to protect it. Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)Q Each IGBT — — 0.16 °C/Watt R th(j-c)F Each FWDi — — 0.24 °C/Watt R th(j-c´)Q Each IGBT — — 0.10 † °C/Watt R th(j-c´)F Each FWDi — — 0.16 † °C/Watt Contact Thermal Resistance R th(c-f) Case to Fin Per Module, — — 0.018 °C/Watt Thermal Grease Applied TC measured point is just under chip. † If you use this value, Rth(f-a) should be measured just under the chips. Recommended Conditions for Use Characteristic Symbol Condition Value Units Supply Voltage V CC Applied across P-N Terminals 0 ~ 800 Volts Control Supply Voltage* V D Applied between VUP1 -VUPC , 15 ± 1.5 Volts VN1 -VNC , VVP1 -VVPC , VWP1 -VWPC Input ON Voltage V CIN(on) Applied between UP-VUPC , VP-VVPC ,0 ~ 0.8 Volts Input OFF Voltage V CIN(off) W P-VWPC , UN, VN, W N -VNC 4.0 ~ VD Volts PWM Input Frequency f PWM Using Application Circuit 0 ~ 20 kHz Minimum Dead Time t DEAD Input Signal ≥ 3.0 µS *** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak.
Intellimod™ Module Three Phase IGBT Inverter Output Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 1.0 2.0 3.0 SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT, I C , (AMPERES) 0 20040 80 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC 0.5 SATURATION VOLTAGE , VCE(sat), (VOLTS) 1.5 2.5 120 160 101 102 103 DIODE FORWARD CHARACTERISTICS (TYPICAL) DIODE FORWARD VOLTAGE, V EC , (VOLTS) DIODE CURRENT, -IC , (AMPERES) Tj = 25oC Tj = 125oC VD = 15V 101 102 103 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, ton, toff, (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) ton 100 101 toff VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 101 102 103 10-1 COLLECTOR CURRENT, I C , (AMPERES) SWITCHING TIMES, tc(on), tc(off), (µs) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) tc(on) 100 101 tc(off) tc(off) VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 101 102 103 10-2 COLLECTOR CURRENT, -I C , (AMPERES) REVERSE RECOVERY TIME, t rr, (µS) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) 10-1 100 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25oC Tj = 125oC 101 REVERSE RECOVERY CURRENT, I rr, (AMPERES) 102 103 trr Irr 120 CIRCUIT CURRENT VS. CARRIER FREQUENCY CARRIER FREQUENCY, f C , (kHz) CIRCUIT CURRENT, ID , (mA) 51 0 1 5 2 0 2 5 Tj = 25oC N-SIDE P-SIDE 100 INDUCTIVE LOAD 101 102 103 10-1 SWITCHING LOSS, E SW , (m)J/PULSE) SWITCHING LOSS CHARACTERISTICS (TYPICAL) 100 102 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25oC Tj = 125oC 101 Esw(off) Esw(off) Esw(on) TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT & FWDi - INVERTER PART) 101 10-1 100 101 100 10-1 10-2 10-3 STANDARD VALUE R th(j-c)Q = 0.16oC/W (IGBT) R th(j-c)F = 0.24oC/W (FWDi) SINGLE PULSE 10-210-3 INDUCTIVE LOAD COLLECTOR CURRENT, I C , (AMPERES)