PIF0605A1R0MN SUPERWORLD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 1. Part No. Expression: P I F 0 6 0 5 A 1 R 0 M N a) Series Code e) Tolerance Code (a) (b) (c) (d) (e)(f) b) Dimension Code f) Internal Controlled Code c) Type Code d) Inductance Code 2. Configuration & Dimensions: Unit: mm 3. Schematic: Part Number A B C D E F L G H L G H Recommended PC Board Pattern Note: 1. The above PCB layout is for reference only. 2. Solder paste thickness of 0.15mm and above is recommended.

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 4. Material List: 5. General Specification: (a) Core (b) Wire (c) Solder (d) Ink (a) Test Freq. : L : 100KHz/0.1V (b) Operating Temp. : -40°C to +125°C (including self-temperature rise) (c) Storage Temp. : -40°C to +125°C (on board) (d) Humidity Range : 85 ± 2% RH (e) Heat Rated Current (Irms) will cause the coil temperature rise approximately Δt of 40°C (keep 1min) (f) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%. (g) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125°C under worst case operating conditions. (h) Storage condition (component in its packaging) i) Temperature: Less than 40°C ii)Humidity : 60% RH

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 6. Electrical Characteristics: *Tolerance code : M = ±20% Notes: 1) Isat Typ. and Irms Typ. value is derived based from accounting the upper limit tolerance into the inductance value. 2) At all times, the current supplied to the product should not exceed Isat Max. value. Part Number Inductance(uH) ±20% @ 0 A I rms(A) Typ. I sat(A) DCR (mΩ) Typ. DCR (mΩ) Max. @20℃ @40℃ Typ. Max.

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 7. Characteristics Curves: PIF0605A1R0MN PIF0605A1R2MN PIF0605A1R5MN PIF0605A1R8MN PIF0605A3R3MN PIF0605A2R2MN PIF0605A4R3MN PIF0605A4R7MN

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 8. Soldering: Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air. 8-1 Solder Re-flow: Recommended temperature profiles for re-flow soldering in Figure 1. 8-2 Soldering Iron (Figure 2): Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150°C. b) 355°C tip temperature (Max.) c) Never contact the ceramic with the iron tip d) 1.0mm tip diameter (Max.) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 4~5 secs.

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 9. Packaging Information: 9-1 Reel Dimension 9-2 Tape Dimension 9-3 Packaging Quantity Type A(mm) B(mm) C(mm) D(mm) PIF 0605A Chip / Reel 800 Inner box 1,600 Carton 6,400 Series Size Ao(mm) Bo(mm) Ko(mm) P(mm) W(mm) F(mm) T(mm) D(mm)

High Current Power Inductor– PIF0605A Series Proprietary and Confidential Document of Superworld 04/05/2016 9-4 Tearing Off Force Application Notice: 1. Storage Conditions: To maintain the solderabililty of terminal electrodes: a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation: a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) Vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions Room Temp. (℃) Room Humidity (%) Room atm (hPa) Tearing Speed mm/min 5~35 45~85 860~1060 300