PIC1005H2R2MN

PIC1005H SUPERWORLD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

P I C 1 0 0 5 H 1 R 0 M N - (a) (d) (b) (e) 1. PART NO. EXPRESSION : (b) Dimension code (c) Type code (a) Series code 2. CONFIGURATION & DIMENSIONS : A SUPERWORLD ELECTRONICS (S) PTE LTD 3. SCHEMATIC : (d) Inductance code : 1R0 = 1.0uH (e) Tolerance code : M = ± 20%, Y = ± 30% PG. 1 10.0± 0.3 BC 4.8± 0.2 D 3.0± 0.3 E Unit:m/m 11.0± 0.5 2.0± 0.3 h) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125° C under worst case operating conditions. f) Heat Rated Current (Irms) : Will cause the coil temp. rise approximately ǻt of 40°C (keep 1min.) g) Saturation Current (Isat) : Will cause L0 to drop 20% typical (keep quickly) 5. GENERAL SPECIFICATION : d) Storage Temp. : -10° C to +40° C c) Operating Temp. : -40° C to +125° C e) Humidity Range : 50 ~ 60% RH (Product without taping) b) Ambient Temp. : 25° C a) Test Freq. : L : 100KHz/1V (c) (f) (f) No coating 1R0 A B C D E 4. MATERIALS : (a) Core : Magnetic metal powder or equivalent (b) Wire : Polyester wire or equivalent (c) Solder Plating : 100% Pb free solder 11.03.2011 MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. (d) Ink : Halogen-free ketone (g) (g) Internal control number : 11 ~ 99 a b c d 1104 HF Halogen Free

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 6. ELECTRICAL CHARACTERISTICS : Inductance L Part No. ( µH ) @ 0 A DCR Typ. @ 25° C ( mȍ ) Irms ( A ) ( A ) Isat Typ. Typ. DCR ( mȍ ) Max. @ 25° C MODLED POWER CHOKE COIL PIC1005H SERIES 11.03.2011 1.00 ± 20% 2.822 30 3.5 2.20 ± 20% 5.4 16 24 6.0 NOTE : Specifications subject to change without notice. Please check our website for latest information. PIC1005H1R0MN PIC1005H2R2MN 0.30 ± 20% 0.57 38 65 0.61PIC1005HR30MN HF Halogen Free

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 11.03.2011 7. CHARACTERISTICS CURVES : MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. TMPC1005H 1R0MN Z01 0. 0 0. 5 1. 0 1. 5 2. 0 DC CURRENT(A) INDUCTANCE(uH) 0 Temp.Ri se(degree ć) TEMP(͠) 0 3 9 16 26 35 45 0 5 10 15 20 24 26 28 32 PIC1005M1R0MN 0. 0 0. 2 0. 3 0. 5 0. 6 DC CURRENT(A) INDUCTANCE(uH) Temp.Rise (degree ć) TEMP(͠)0 2 7 1 6 2 8 4 5 0 1 02 03 03 84 55 05 56 06 5 PIC1005MR30MN HF Halogen Free

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 11.03.2011 7. CHARACTERISTICS CURVES : MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. TMPC1005H 2R2MN Z01 0. 0 1. 0 2. 0 3. 0 4. 0 DC CURRENT(A) INDUCTANCE(uH) 0 Temp.Ri se(degree ć) TEMP(͠) 0 1 5 12 23 44 67 0 4 8 12 16 20 24 PIC1005M2R2MN HF Halogen Free

PG. 5 SUPERWORLD ELECTRONICS (S) PTE LTD 8. RELIABILITY AND TEST CONDITION Humidity Resistance Thermal Shock Temperature Test Reliability Test Measure at room temperature after placing for 2 to 3 hrs. Humidity : 85± 3% RH Time : 1000± 12hrs Temperature : 85± 2° C Total : 300 cycles Step Conditions of 1 cycle. Room Temperature +125+2/-0 -40+0/-2 15± 1 15± 1 Temperature (° C) Times (min.) Measured at room temperature after placing for 2 to 3hrs Time : 1000± 12hrs Temperature : 125± 2° C Refer to standard electrical characteristics list PERFORMANCE Electrical Characteristics Test Saturation Current (Isat) Heat Rated Current (Irms) DCR Inductance ITEM HP4284A, CH11025, CH3302, CH1320, CH1320S CH16502, Agilent33420A Micro-Ohm Meter. LCR meter. TEST CONDITION Random Vibration This cycle shall be performed 12 times in each of three mutually perpendicular directions. Amplitude: Parts mounted within 2" from any secure point Frequency : 10-2000-10Hz for 20 min. Test (MIL-PRF-27) (AEC-Q200-REV C) Temperature : 260± 5° C, 20-40 seconds Duration : 5 minutes Preheat : 150± 5° CReflow Test Electric specification should be satisfied Solder test After dip into fluxˈdip into solder 235± 5° C, 4± 1seconds Flux, solder for lead free (ANSI/J-STD-002C Method B) Terminals should be covered by over 95% solder on visual inspection. 2. Temperature measured by digital surface thermometer 1. Applied the allowed DC current(keep 1min). approximately ǻT of 40°C without core loss Irms(A) will cause the coil temperature rise Isat(A) will cause Lo to drop Directions and times : X, Y, Z directions for 20 min. Within <0.2 Measured at room temperature after placing for 2 to 3hrs (AEC-Q200-REV C) 11.03.2011 (Total 12hours). (MIL-STD-202 Method 204 D Test condition B) (IPC/JEDEC J-STD-020C) MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. ǻL20% typical Temperature Test Measured at room temperature after placing for 2 to 3hrs Time :500± 12hrs Temperature : -40± 2° CLow High HF Halogen Free

SUPERWORLD ELECTRONICS (S) PTE LTD PG. 7 10. PACKAGING INFORMATION : Bo Ko t4.0 Ø1.52.0 1.75 Bo(mm) 11.6± 0.1 10-3. Packaging Quantity PIC1005H Series Ao(mm) F(mm) Ao P(mm) 16.0 ± 0.1 Ko(mm) 5.3± 0.1 W(mm) 24.0± 0.3 P 0.35± 0.05 t(mm) F W 10-2 Tape Dimension 24.0± 0.5 A(mm) 13" x 24mm Type 100± 2.0 B(mm) D D(mm) 13.5± 0.5 330 C(mm) EMBOSSED CARRIER B A COVER TAPE 10-1. Reel Dimension 1005 4000 1000 Carton Chip / Reel Inner Box Size 500 2.0± 0.5 ØC 11.03.2011 MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. 1R0 1R0 1R0 1R0 1R0 1R0 1R0 1R0 1R0 1024 1024 1024 1024 1024 1024 1024 1024 1024 HF Halogen Free

SUPERWORLD ELECTRONICS (S) PTE LTD 10-4. Tearing Off Force The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions. a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 1. Storage Conditions : To maintain the solderabililty of terminal electrodes : a) Temperature and humidity conditions : Less than 30° C and 70% RH. b) Recommended products should be used within 6 months from the time of delivery. c) The packaging material should be kept where no chlorine or sulfur exists in the air. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. 2. Transportation : Application Notice Top cover tape F Base tape 165° to 180° Room Temp. (° C) 5~35 Room Humidity (%) 45~85 Tearing Speed (mm/min) 300 Room atm (hPa) 860~1060 PG. 8 (referenced ANSI/EIA-481-C-2003 of 4.11 standard) 11.03.2011 MODLED POWER CHOKE COIL PIC1005H SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. HF Halogen Free