PIA1005SR36MN SUPERWORLD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 1. Part No. Expression: P I A 1 0 0 5 S 1 R 0 M N a) Series Code e) Tolerance Code (a) (b) (c) (d) (e)(f) b) Dimension Code f) Internal Control Code c) Type Code d) Inductance Code 2. Configuration & Dimensions: a. Lead Frame b. Non Lead Frame 3. Schematic: A A\` B C D T G H L E Inductance 2.5±0.3 Between 0.68-1.50uH 3.0±0.3 0.47uH and below 2.20uH and above Note: 1. The above PCB layout is for reference only. 2. Solder paste thickness of 0.15mm and above is recommended. 3. Markin g: Top row – Inductance code, Bottom row – YYWW L G H Recommend PC Board Pattern Unit: mm Marking D/C Marking D/C

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 4. Material List: i ) L e a d F r a m e i i ) N o n - l e a d F r a m e a) Core b) Wire c) Terminal d) Ink 5. General Specification: (a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise) (b) Storage Temp. : -40°C to +125°C (on board) (c) Humidity Range : 85 ± 2% RH (d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C (keep 1min) (e) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%. (f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions. (g) Storage condition (component in its packaging) i) Temperature: -10 to 40°C ii) Humidity : 50~60% RH

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 6. Electrical Characteristics: Notes: 1) At all times, the current supplied to the product should not exceed Isat Max. value. Part Number Inductance Lo (uH) @ 0A ±20% Test Frequency, L Heat Rating Current DC ( A ) Irms. Saturation Current DC (A) Isat. DCR (mΩ)Typ. DCR (mΩ)Max. Type Typ. Max. Typ. Max.

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 7. Characteristics Curves: PIA1005SR36MN PIA1005SR47MN PIA1005SR68MN PIA1005S1R0MN PIA1005S1R5MN PIA1005S2R2MN PIA1005S3R3MN PIA1005S4R7MN PIA1005S5R6MN PIA1005S6R8MN PIA1005S100MN PIA1005S101MN

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 8. Soldering: Mildly activated rosin fluxes are preferred. The minimu m amount of solder can lead to damage from the stresses caused by the differenc e in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is t he utilization of hot air. 8-1 Solder Re-flow: Recommended temperature profiles for re-flow soldering in Figure 1. 8-2 Soldering Iron (Figure 2): Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. N o t e : a) Preheat circuit and products to 150°C. b) 355°C tip temperature (Max.) c ) N e v e r c o n t a c t t h e c e r a m i c w i t h t h e i r o n t i p d) 1.0mm tip diameter (Max.) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f ) L i m i t s o l d e r i n g t i m e t o 4 ~ 5 s e c s .

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 C D 2.0±0.5 EMBOSSED CARRIER B A COVER TAPE 9. Packaging Information: 9-1 Reel Dimension: 9 - 2 T a p e D i m e n s i o n : 9-3 Packaging Quantity: Type A(mm) B(mm) C(mm) D(mm) PIA 1005 Chip / Reel 500 Inner box 1000 Carton 4000 Series Size Bo(mm) Ao(mm) Ko(mm) P(mm) W(mm) F(mm) T(mm) D(mm)

Molded Choke Coil – PIA1005S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 29/09/2017 9-4 Tearing Off Force: Application Notice: 1. Storage Conditions: To maintain the solderabililty of terminal electrodes: a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation: a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) Vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. Room Temp. (℃) Room Humidity (%) Room atm (hPa) Tearing Speed mm/min 5~35 45~85 860~1060 300 The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions.